In parport_serial , I request a irq and request region to initialize 887x ,
so I must run a additional ite887x_removecheck function to check it.
Some type of 887x only with serial or only with parport , so that
sometimes the port num would be 0 .
I want the driver can proceed with runing even the card with no parport , or with on serial.
( the original driver return -ENODEV while fail in parport_register or serial_register )
I set success = 1 while the port num =0 in the tables , to avoid fail from parport register or serial register.
I also fix a bug while printk the parport information.
The original driver printk parport_serial_pci_tb[i].vendor ,
the index "i" is be used to cards[i].....but parport_serial_pci_tbl and cards are not match.
The bug will show wrong message wile printk parport information,
so I fix it to be dev->vendor , to show the correct message.
--- parport_pc.c 2002-11-29 07:53:14.000000000 +0800
+++ /parport_pc_ite887x.c 2003-05-27 14:32:37.000000000 +0800
@@ -2436,103 +2436,6 @@
#ifdef CONFIG_PCI
-/* ITE support maintained by Rich Liu <richliu@poorman.org> */
-static int __devinit sio_ite_8872_probe (struct pci_dev *pdev, int autoirq,
- int autodma)
-{
- short inta_addr[6] = { 0x2A0, 0x2C0, 0x220, 0x240, 0x1E0 };
- u32 ite8872set;
- u32 ite8872_lpt, ite8872_lpthi;
- u8 ite8872_irq, type;
- int irq;
- int i;
-
- DPRINTK (KERN_DEBUG "sio_ite_8872_probe()\n");
-
- // make sure which one chip
- for(i = 0; i < 5; i++) {
- if (check_region (inta_addr[i], 0x8) >= 0) {
- int test;
- pci_write_config_dword (pdev, 0x60,
- 0xe7000000 | inta_addr[i]);
- pci_write_config_dword (pdev, 0x78,
- 0x00000000 | inta_addr[i]);
- test = inb (inta_addr[i]);
- if (test != 0xff) break;
- }
- }
- if(i >= 5) {
- printk (KERN_INFO "parport_pc: cannot find ITE8872 INTA\n");
- return 0;
- }
-
- type = inb (inta_addr[i] + 0x18);
- type &= 0x0f;
-
- switch (type) {
- case 0x2:
- printk (KERN_INFO "parport_pc: ITE8871 found (1P)\n");
- ite8872set = 0x64200000;
- break;
- case 0xa:
- printk (KERN_INFO "parport_pc: ITE8875 found (1P)\n");
- ite8872set = 0x64200000;
- break;
- case 0xe:
- printk (KERN_INFO "parport_pc: ITE8872 found (2S1P)\n");
- ite8872set = 0x64e00000;
- break;
- case 0x6:
- printk (KERN_INFO "parport_pc: ITE8873 found (1S)\n");
- return 0;
- case 0x8:
- DPRINTK (KERN_DEBUG "parport_pc: ITE8874 found (2S)\n");
- return 0;
- default:
- printk (KERN_INFO "parport_pc: unknown ITE887x\n");
- printk (KERN_INFO "parport_pc: please mail 'lspci -nvv' "
- "output to Rich.Liu@ite.com.tw\n");
- return 0;
- }
-
- pci_read_config_byte (pdev, 0x3c, &ite8872_irq);
- pci_read_config_dword (pdev, 0x1c, &ite8872_lpt);
- ite8872_lpt &= 0x0000ff00;
- pci_read_config_dword (pdev, 0x20, &ite8872_lpthi);
- ite8872_lpthi &= 0x0000ff00;
- pci_write_config_dword (pdev, 0x6c, 0xe3000000 | ite8872_lpt);
- pci_write_config_dword (pdev, 0x70, 0xe3000000 | ite8872_lpthi);
- pci_write_config_dword (pdev, 0x80, (ite8872_lpthi<<16) | ite8872_lpt);
- // SET SPP&EPP , Parallel Port NO DMA , Enable All Function
- // SET Parallel IRQ
- pci_write_config_dword (pdev, 0x9c,
- ite8872set | (ite8872_irq * 0x11111));
-
- DPRINTK (KERN_DEBUG "ITE887x: The IRQ is %d.\n", ite8872_irq);
- DPRINTK (KERN_DEBUG "ITE887x: The PARALLEL I/O port is 0x%x.\n",
- ite8872_lpt);
- DPRINTK (KERN_DEBUG "ITE887x: The PARALLEL I/O porthi is 0x%x.\n",
- ite8872_lpthi);
-
- /* Let the user (or defaults) steer us away from interrupts */
- irq = ite8872_irq;
- if (autoirq != PARPORT_IRQ_AUTO)
- irq = PARPORT_IRQ_NONE;
-
- if (parport_pc_probe_port (ite8872_lpt, ite8872_lpthi,
- irq, PARPORT_DMA_NONE, NULL)) {
- printk (KERN_INFO
- "parport_pc: ITE 8872 parallel port: io=0x%X",
- ite8872_lpt);
- if (irq != PARPORT_IRQ_NONE)
- printk (", irq=%d", irq);
- printk ("\n");
- return 1;
- }
-
- return 0;
-}
-
/* Via support maintained by Jeff Garzik <jgarzik@mandrakesoft.com> */
static int __devinit sio_via_686a_probe (struct pci_dev *pdev, int autoirq,
int autodma)
@@ -2643,7 +2546,6 @@
enum parport_pc_sio_types {
sio_via_686a = 0, /* Via VT82C686A motherboard Super I/O */
- sio_ite_8872,
last_sio
};
@@ -2652,7 +2554,6 @@
int (*probe) (struct pci_dev *pdev, int autoirq, int autodma);
} parport_pc_superio_info[] __devinitdata = {
{ sio_via_686a_probe, },
- { sio_ite_8872_probe, },
};
@@ -2773,8 +2674,6 @@
static struct pci_device_id parport_pc_pci_tbl[] __devinitdata = {
/* Super-IO onboard chips */
{ 0x1106, 0x0686, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_686a },
- { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_ite_8872 },
/* PCI cards */
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_10x,
--- parport_serial.c 2003-06-11 10:57:11.000000000 +0800
+++ parport_serial_ite887x.c 2003-06-11 10:56:25.000000000 +0800
@@ -29,6 +29,15 @@
#include <asm/serial.h>
+/*
+ * ITE 887x
+ */
+int ITEBOARDNUMBER = 0, ite887x_index, rm_ite = 0;
+u32 ITE887x_INTC[8];
+u16 ITE887x_INTA[8];
+u8 ITE887x_IRQ[8];
+int __devinit pci_ite887x_fn(struct pci_dev *dev, int autoirq, int autodma);
+
enum parport_pc_pci_cards {
titan_110l = 0,
titan_210l,
@@ -46,6 +55,7 @@
siig_2p1s_20x,
siig_1s1p_20x,
siig_2s1p_20x,
+ ite_887x,
};
@@ -84,6 +94,7 @@
/* siig_2p1s_20x */ { 2, { { 1, 2 }, { 3, 4 }, } },
/* siig_1s1p_20x */ { 1, { { 1, 2 }, } },
/* siig_2s1p_20x */ { 1, { { 2, 3 }, } },
+ /* ite_887x */ { 0, { { 3, 4 }, }, pci_ite887x_fn },
};
static struct pci_device_id parport_serial_pci_tbl[] __devinitdata = {
@@ -132,6 +143,8 @@
PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2s1p_20x },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S1P_20x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2s1p_20x },
+ { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, ite_887x},
{ 0, } /* terminate list */
};
@@ -185,6 +198,7 @@
/* siig_2p1s_20x */ { SPCI_FL_BASE0, 1, 921600, 0, 0, siig20x_init_fn },
/* siig_1s1p_20x */ { SPCI_FL_BASE0, 1, 921600, 0, 0, siig20x_init_fn },
/* siig_2s1p_20x */ { SPCI_FL_BASE0, 1, 921600, 0, 0, siig20x_init_fn },
+/* ite_887x */ { SPCI_FL_BASE1 | SPCI_FL_BASE_TABLE, 0, 115200 },
};
struct parport_serial_private {
@@ -195,6 +209,165 @@
struct parport *port[PARPORT_MAX];
};
+/*
+ * Integrated Technology Express, Inc. IT887x Device Driver
+ */
+
+ite887x_removecheck(struct pci_dev *dev)
+{
+ if (dev->vendor == PCI_VENDOR_ID_ITE
+ && dev->device == PCI_DEVICE_ID_ITE_8872) {
+ free_irq(dev->irq, dev);
+ release_region(ITE887x_INTA[rm_ite++], 0x8);
+ }
+}
+
+void ite887x_requestirq(int irq, void *dev_id, struct pt_regs *regs)
+{
+ u8 itmp;
+ int i = 0;
+ /* measure which INTC went to control */
+ for (i = 0; i < 8; i++)
+ if (irq == ITE887x_IRQ[i]) {
+ /* clean ITE887x interrupt */
+ itmp = inb(ITE887x_INTC[i] + 2);
+ if (itmp && 0xf) {
+ outb(itmp, ITE887x_INTC[i] + 2);
+ break;
+ }
+ }
+}
+
+int __devinit pci_ite887x_fn(struct pci_dev *dev, int autoirq, int autodma)
+{
+ int result, ite887xcomnum = 0, ite887xparportnum = 0;
+ short INTA_Addr[8] = { 0x2a0, 0x2c0, 0x220, 0x240, 0x1E0, 0x200, 0x280 };
+ u32 j, u32Tmp, itmp, ITE887x_COM1, ITE887x_COM2, ITE887xSET = 0x64E00000, set60, set78, ite887x_lpt, ite887x_lpthi;
+
+ pci_read_config_dword(dev, 0x60, &set60);
+ pci_read_config_dword(dev, 0x78, &set78);
+
+ for (j = 0; j < 7; j++)
+ if (check_region(INTA_Addr[j], 0x8) >= 0) {
+ pci_write_config_dword(dev, 0x60, 0xE7000000 | INTA_Addr[j]);
+ pci_write_config_dword(dev, 0x78, 0x00000000 | INTA_Addr[j]);
+ itmp = inb(INTA_Addr[j]);
+ if (itmp != 0xFF)
+ break;
+ }
+
+ if (j >= 7) {
+ printk(KERN_INFO "ITE887x INTA cannot find.\n");
+ return 0;
+ }
+ /* Detect the type of 887x */
+ ITE887x_INTA[ITEBOARDNUMBER] = INTA_Addr[j];
+ itmp = INTA_Addr[j];
+ u32Tmp = inb(itmp + 0x18);
+ u32Tmp &= 0x0F;
+ switch (u32Tmp) {
+ case 0x2:
+ printk(KERN_INFO "ITE887x: ITE8871 found , Parallel*1 \n");
+ ITE887xSET = 0x64200000;
+ ite887xcomnum = 0;
+ ite887xparportnum = 1;
+ request_region(INTA_Addr[j], 0x8, "ite8871");
+ break;
+ case 0xA:
+ printk(KERN_INFO "ITE887x: ITE8875 found , Parallel*1 \n");
+ ITE887xSET = 0x64200000;
+ ite887xcomnum = 0;
+ ite887xparportnum = 1;
+ request_region(INTA_Addr[j], 0x8, "ite8875");
+ break;
+ case 0xE:
+ printk(KERN_INFO
+ "ITE887x: ITE8872 found , Serial *2 , Parallel*1 \n");
+ ite887xcomnum = 2;
+ ite887xparportnum = 1;
+ ITE887xSET = 0x64E00000;
+ request_region(INTA_Addr[j], 0x8, "ite8872");
+ break;
+ case 0x6:
+ printk(KERN_INFO "ITE887x: ITE8873 found , Serial *1 \n");
+ ite887xcomnum = 1;
+ ite887xparportnum = 0;
+ ITE887xSET = 0x64800000;
+ request_region(INTA_Addr[j], 0x8, "ite8873");
+ break;
+ case 0x8:
+ printk(KERN_INFO "ITE887x: ITE8874 found , Serial *2 \n");
+ ite887xcomnum = 2;
+ ite887xparportnum = 0;
+ ITE887xSET = 0x64C00000;
+ request_region(INTA_Addr[j], 0x8, "ite8874");
+ break;
+ default:
+ ite887xcomnum = 0;
+ ite887xparportnum = 0;
+ printk(KERN_INFO "ITE887x: unknow ITE887x \n");
+ printk(KERN_INFO
+ "ITE887x: please mail lspci -nvv output to ted.wen@ite.com.tw\n");
+ pci_write_config_dword(dev, 0x60, set60);
+ pci_write_config_dword(dev, 0x78, set78);
+ return 0;
+ break;
+ }
+ cards[ite887x_index].numports = ite887xparportnum;
+ pci_boards[ite887x_index].num_ports = ite887xcomnum;
+ ITE887x_IRQ[ITEBOARDNUMBER] = dev->irq;
+ printk(KERN_INFO "ITE887X_IRQ : %d \n", ITE887x_IRQ[ITEBOARDNUMBER]);
+ result = request_irq(ITE887x_IRQ[ITEBOARDNUMBER], ite887x_requestirq, SA_SHIRQ, "ite887x", dev);
+ if (result) {
+ printk(KERN_INFO "ITE887x: can't get assign irq :%x \n",
+ ITE887x_IRQ[ITEBOARDNUMBER]);
+ return 0;
+ }
+
+ /* INTC */
+ pci_read_config_dword(dev, 0x10, &ITE887x_INTC[ITEBOARDNUMBER]);
+ ITE887x_INTC[ITEBOARDNUMBER] &= 0x0000FF00;
+ pci_write_config_dword(dev, 0x60, 0xE5000000 | ITE887x_INTC[ITEBOARDNUMBER]);
+ pci_write_config_dword(dev, 0x78, ITE887x_INTC[ITEBOARDNUMBER]);
+
+ if (ite887xcomnum >= 1) {
+ /* COM1 */
+ pci_read_config_dword(dev, 0x14, &ITE887x_COM1);
+ ITE887x_COM1 &= 0x0000FF00;
+ pci_write_config_dword(dev, 0x64, 0xE3000000 | ITE887x_COM1);
+
+ /* COM2 */
+ if (ite887xcomnum == 2) {
+ pci_read_config_dword(dev, 0x18, &ITE887x_COM2);
+ ITE887x_COM2 &= 0x0000FF00;
+ pci_write_config_dword(dev, 0x68, 0xE3000000 | ITE887x_COM2);
+ } else
+ ITE887x_COM2 = 0;
+
+ pci_write_config_dword(dev, 0x7C, (ITE887x_COM2 << 16) | (ITE887x_COM1));
+ }
+
+ /* Parport */
+ if (ite887xparportnum >= 1) {
+ pci_read_config_dword(dev, 0x1c, &ite887x_lpt);
+ ite887x_lpt &= 0x0000ff00;
+ pci_read_config_dword(dev, 0x20, &ite887x_lpthi);
+ ite887x_lpthi &= 0x0000ff00;
+ pci_write_config_dword(dev, 0x6c, 0xe3000000 | ite887x_lpt);
+ pci_write_config_dword(dev, 0x70, 0xe3000000 | ite887x_lpthi);
+ pci_write_config_dword(dev, 0x80, (ite887x_lpthi << 16) | ite887x_lpt);
+ printk(KERN_INFO "ITE887x: The PARALLEL I/O port is 0x%x.\n",
+ ite887x_lpt);
+ printk(KERN_INFO "ITE887x: The PARALLEL I/O porthi is 0x%x.\n",
+ ite887x_lpthi);
+ }
+ /* 9C write enable UART , IRQ Function */
+ pci_write_config_dword(dev, 0x9c, ITE887xSET | (0x11111 * ITE887x_IRQ[ITEBOARDNUMBER]));
+ /* Add next interface */
+ ITEBOARDNUMBER++;
+ return 0;
+}
+
static int __devinit get_pci_port (struct pci_dev *dev,
struct pci_board_no_ids *board,
struct serial_struct *req,
@@ -276,6 +449,8 @@
base_baud = BASE_BAUD;
memset (&serial_req, 0, sizeof (serial_req));
+ if (board->num_ports == 0)
+ success = 1;
for (k = 0; k < board->num_ports; k++) {
int line;
serial_req.irq = dev->irq;
@@ -308,6 +483,8 @@
cards[i].preinit_hook (dev, PARPORT_IRQ_NONE, PARPORT_DMA_NONE))
return -ENODEV;
+ if (cards[i].numports == 0)
+ success = 1;
for (n = 0; n < cards[i].numports; n++) {
struct parport *port;
int lo = cards[i].addr[n].lo;
@@ -324,8 +501,8 @@
/* TODO: test if sharing interrupts works */
printk (KERN_DEBUG "PCI parallel port detected: %04x:%04x, "
"I/O at %#lx(%#lx)\n",
- parport_serial_pci_tbl[i].vendor,
- parport_serial_pci_tbl[i].device, io_lo, io_hi);
+ dev->vendor,
+ dev->device, io_lo, io_hi);
port = parport_pc_probe_port (io_lo, io_hi, PARPORT_IRQ_NONE,
PARPORT_DMA_NONE, dev);
if (port) {
@@ -359,6 +536,7 @@
return err;
}
+ ite887x_index = id->driver_data;
if (parport_register (dev, id)) {
pci_set_drvdata (dev, NULL);
kfree (priv);
@@ -395,6 +573,7 @@
for (i = 0; i < priv->num_par; i++)
parport_pc_unregister_port (priv->port[i]);
+ ite887x_removecheck(dev);
kfree (priv);
return;
}
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/