Why did I wrote 2.4.17? I must have been sleeping deeply. I meant 2.4.21.
Please excuse me - it was my fault.
Kind regards,
Andreas Hartmann
That's what I wrote:
Hello all,
I'm using a 8K5A motherboard with APIC (MPS 1.4 / 1.1; Epox says in the
manual, that linux would use this version) turned on in bios and kernel.
Using this configuration breakes the onboard sound (VT8233/A/8235 AC97
Audio Controller (rev 50)).
> dmesg
Linux version 2.4.21-rc7 (root@athlon) (gcc version 3.2.3) #3 Sam Jun 7
20:03:20 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000f5d40
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Kernel command line: BOOT_IMAGE=2421rc7 rw root=301
BOOT_FILE=/boot/vmlinuz-2.4.21-rc7 init 2
Initializing CPU#0
Detected 1670.487 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3335.78 BogoMIPS
Memory: 516480k/524224k available (1021k kernel code, 7356k reserved, 224k
data, 236k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU: AMD Athlon(tm) XP 2000+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-20, 2-21, 2-22, 2-23 not
connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 24.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 001 01 0 0 0 0 0 1 1 51
07 001 01 0 0 0 0 0 1 1 59
08 001 01 0 0 0 0 0 1 1 61
09 001 01 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 71
0d 001 01 0 0 0 0 0 1 1 79
0e 001 01 0 0 0 0 0 1 1 81
0f 001 01 0 0 0 0 0 1 1 89
10 001 01 1 1 0 1 0 1 1 91
11 001 01 1 1 0 1 0 1 1 99
12 001 01 1 1 0 1 0 1 1 A1
13 001 01 1 1 0 1 0 1 1 A9
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1670.5134 MHz.
..... host bus clock speed is 267.2820 MHz.
cpu: 0, clocks: 2672820, slice: 1336410
CPU0<T0:2672816,T1:1336400,D:6,S:1336410,C:2672820>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb3f0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router VIA [1106/3177] at 00:11.0
PCI->APIC IRQ transform: (B0,I9,P0) -> 17
PCI->APIC IRQ transform: (B0,I11,P0) -> 19
PCI->APIC IRQ transform: (B0,I12,P0) -> 18
PCI->APIC IRQ transform: (B0,I16,P0) -> 16
PCI->APIC IRQ transform: (B0,I16,P1) -> 17
PCI->APIC IRQ transform: (B0,I16,P2) -> 18
PCI->APIC IRQ transform: (B0,I16,P3) -> 19
PCI->APIC IRQ transform: (B0,I17,P0) -> 16
PCI->APIC IRQ transform: (B0,I17,P2) -> 18
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI: Via IRQ fixup for 00:10.0, from 11 to 0
PCI: Via IRQ fixup for 00:10.1, from 5 to 1
PCI: Via IRQ fixup for 00:10.2, from 11 to 2
> lspci -v
00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
Flags: bus master, 66Mhz, medium devsel, latency 0
Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2
00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333
AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: d8000000-dbffffff
Capabilities: [80] Power Management version 2
00:09.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 10/100
Ethernet (rev 02)
Subsystem: Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet
Adapter
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at d000 [size=256]
Memory at df022000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [40] Power Management version 1
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at d400 [size=256]
Memory at df020000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
00:0c.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev
0c)
Subsystem: Intel Corp. EtherExpress PRO/100 S Desktop Adapter
Flags: bus master, medium devsel, latency 32, IRQ 11
Memory at df021000 (32-bit, non-prefetchable) [size=4K]
I/O ports at d800 [size=64]
Memory at df000000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00
[UHCI])
Subsystem: VIA Technologies, Inc. USB
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at dc00 [size=32]
Capabilities: [80] Power Management version 2
00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00
[UHCI])
Subsystem: VIA Technologies, Inc. USB
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at e000 [size=32]
Capabilities: [80] Power Management version 2
00:10.2 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00
[UHCI])
Subsystem: VIA Technologies, Inc. USB
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at e400 [size=32]
Capabilities: [80] Power Management version 2
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20
[EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at df023000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc. VT8235 ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc.
VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Flags: bus master, medium devsel, latency 32
I/O ports at e800 [size=16]
Capabilities: [c0] Power Management version 2
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235
AC97 Audio Controller (rev 50)
Subsystem: Unknown device 1695:3005
Flags: medium devsel, IRQ 11
I/O ports at ec00 [size=256]
Capabilities: [c0] Power Management version 2
01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 PF/PRO AGP
4x TMDS (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Rage Fury Pro/Xpert 2000 Pro
Flags: bus master, stepping, 66Mhz, medium devsel, latency 32, IRQ
11
Memory at d8000000 (32-bit, prefetchable) [size=64M]
I/O ports at c000 [size=256]
Memory at dd000000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] AGP version 2.0
Capabilities: [5c] Power Management version 2
> cat /proc/interupts (MSP version 1.4)
CPU0
0: 72798 IO-APIC-edge timer
1: 3355 IO-APIC-edge keyboard
2: 0 XT-PIC cascade
7: 2 IO-APIC-edge parport0
12: 22081 IO-APIC-edge PS/2 Mouse
14: 28730 IO-APIC-edge ide0
15: 2 IO-APIC-edge ide1
17: 4184 IO-APIC-level eth0
18: 4 IO-APIC-level eth1, via82cxxx
NMI: 0
LOC: 72753
ERR: 0
MIS: 0
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/