arnouten@setzer:~$ ping mintzer
PING mintzer.bzzt.net (195.169.216.157) 56(84) bytes of data.
64 bytes from vhe-400091.sshn.net (195.169.216.157): icmp_seq=1 ttl=64 time=0.192 ms
64 bytes from 195.169.216.157: icmp_seq=2 ttl=64 time=0.135 ms
WARNING: failed to install socket filter
: Protocol not available
Information below was taken after the reboot directly after the crash.
Oops.file was copy-pasted from /var/log/messages.
I hope it means more to you than it does to me :)
I only used USAGI, no other patches applied.
[3.] kernel oops.
[4.] Linux version 2.4.20usagi-s20030414 (root@mintzer) (gcc version
2.95.4 20011002 (Debian prerelease)) #1 Fri Apr 25 13:47:03 CEST 2003
[5.]
Jun 10 13:33:40 mintzer kernel: c01069c5
Jun 10 13:33:40 mintzer kernel: Oops: 0000
Jun 10 13:33:40 mintzer kernel: CPU: 0
Jun 10 13:33:40 mintzer kernel: EIP: 0010:[<c01069c5>] Not tainted
Using defaults from ksymoops -t elf32-i386 -a i386
Jun 10 13:33:40 mintzer kernel: EFLAGS: 00210286
Jun 10 13:33:40 mintzer kernel: eax: c89b5f5e ebx: c89b4000 ecx:
c0a9d000 edx: 00000000
Jun 10 13:33:40 mintzer kernel: esi: 00000000 edi: 00000000 ebp:
c89b5fc4 esp: c89b5f28
Jun 10 13:33:40 mintzer kernel: ds: 0018 es: 0018 ss: 0018
Jun 10 13:33:40 mintzer kernel: Process ntpd (pid: 430,
stackpage=c89b5000)
Jun 10 13:33:40 mintzer kernel: Stack: c89b4000 00000000 00000000
bffffdac c8a32f40 00000000 c013bd68 c89b5f6c
Jun 10 13:33:40 mintzer kernel: 00000004 00000001 c0a9ddd8
00000304 00000080 c89b4000 00200286 00000004
Jun 10 13:33:40 mintzer kernel: 00000001 c0a9ddd8 fffffdfe
c013bdaa c0a9ddc0 c013c20f c0a9ddc0 00000004
Jun 10 13:33:40 mintzer kernel: Call Trace: [<c013bd68>] [<c013bdaa>]
[<c013c20f>] [<c0106d3c>]
Jun 10 13:33:40 mintzer kernel: Code: 03 83 f8 03 74 0a b8 01 00 00 00
e9 23 02 00 00 83 7c 24 14
>>EIP; c01069c5 <do_signal+15/260> <=====
>>eax; c89b5f5e <_end+86c97d6/105e2878>
>>ebx; c89b4000 <_end+86c7878/105e2878>
>>ecx; c0a9d000 <_end+7b0878/105e2878>
>>ebp; c89b5fc4 <_end+86c983c/105e2878>
>>esp; c89b5f28 <_end+86c97a0/105e2878>
Trace; c013bd68 <do_select+1c8/1e0>
Trace; c013bdaa <select_bits_free+a/10>
Trace; c013c20f <sys_select+45f/470>
Trace; c0106d3c <signal_return+14/18>
Code; c01069c5 <do_signal+15/260>
00000000 <_EIP>:
Code; c01069c5 <do_signal+15/260> <=====
0: 03 83 f8 03 74 0a add 0xa7403f8(%ebx),%eax <=====
Code; c01069cb <do_signal+1b/260>
6: b8 01 00 00 00 mov $0x1,%eax
Code; c01069d0 <do_signal+20/260>
b: e9 23 02 00 00 jmp 233 <_EIP+0x233> c0106bf8 <do_signal+248/260>
Code; c01069d5 <do_signal+25/260>
10: 83 7c 24 14 00 cmpl $0x0,0x14(%esp,1)
[6.] unknown, it only occured once until now.
[7.1.]
Linux mintzer 2.4.20usagi-s20030414 #1 Fri Apr 25 13:47:03 CEST 2003
i686 unknown
Gnu C 2.95.4
Gnu make 3.79.1
util-linux 2.11n
mount 2.11n
modutils 2.4.15
e2fsprogs 1.27
reiserfsprogs 3.x.1b
Linux C Library 2.2.5
Dynamic linker (ldd) 2.2.5
Procps 2.0.7
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 2.0.11
Modules Loaded snd-pcm-oss snd-pcm-plugin ipt_state
iptable_mangle iptable_nat iptable_filter 3c59x snd-mixer-oss
snd-card-via686a snd-pcm snd-timer snd-ac97-codec snd-mixer
snd-mpu401-uart snd-rawmidi snd-seq-device snd ide-scsi scsi_mod
[7.2.]
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 7
model name : AMD Duron(tm) processor
stepping : 0
cpu MHz : 999.561
cache size : 64 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca
cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 1992.29
[7.3.]
snd-pcm-oss 18560 1 (autoclean)
snd-pcm-plugin 14864 0 (autoclean) [snd-pcm-oss]
ipt_state 608 2 (autoclean)
iptable_mangle 2304 0 (autoclean) (unused)
iptable_nat 14644 1 (autoclean)
iptable_filter 1760 1 (autoclean)
3c59x 25320 2
snd-mixer-oss 4992 0 (autoclean) [snd-pcm-oss]
snd-card-via686a 6912 1 (autoclean)
snd-pcm 30720 0 (autoclean) [snd-pcm-oss snd-pcm-plugin
snd-card-via686a]
snd-timer 9024 0 (autoclean) [snd-pcm]
snd-ac97-codec 23584 0 (autoclean) [snd-card-via686a]
snd-mixer 27592 0 (autoclean) [snd-mixer-oss
snd-ac97-codec]
snd-mpu401-uart 2336 0 (autoclean) [snd-card-via686a]
snd-rawmidi 10272 0 (autoclean) [snd-mpu401-uart]
snd-seq-device 3820 0 (autoclean) [snd-rawmidi]
snd 33152 1 (autoclean) [snd-pcm-oss snd-pcm-plugin
snd-mixer-oss snd-card-via686a snd-pcm snd-timer snd-ac97-codec
snd-mixer snd-mpu401-uart snd-rawmidi snd-seq-device]
ide-scsi 7776 0
scsi_mod 83576 1 [ide-scsi]
[7.4.]
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial(set)
0300-0301 : VIA 82C686A - MPU401
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(set)
0cf8-0cff : PCI conf1
5000-500f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
6000-607f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
c000-c00f : VIA Technologies, Inc. VT82C586B PIPC Bus Master IDE
00-c007 : ide0
c008-c00f : ide1
c400-c41f : VIA Technologies, Inc. USB
c800-c81f : VIA Technologies, Inc. USB (#2)
cc00-ccff : VIA Technologies, Inc. VT82C686 AC97 Audio Controller
cc00-ccff : VIA 82C686A - AC'97
d000-d003 : VIA Technologies, Inc. VT82C686 AC97 Audio Controller
d400-d403 : VIA Technologies, Inc. VT82C686 AC97 Audio Controller
d400-d403 : VIA 82C686A - MPU401 config
dc00-dc7f : 3Com Corporation 3c905C-TX/TX-M [Tornado]
dc00-dc7f : 00:09.0
e000-e07f : 3Com Corporation 3c905C-TX/TX-M [Tornado] (#2)
e000-e07f : 00:0a.0
00000000-0009ffff : System RAM
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000c8000-000c87ff : Extension ROM
000c9000-000c97ff : Extension ROM
000f0000-000fffff : System ROM
00100000-0ffeffff : System RAM
00100000-002387c4 : Kernel code
002387c5-002ac6c3 : Kernel data
0fff0000-0fff2fff : ACPI Non-volatile Storage
0fff3000-0fffffff : ACPI Tables
d0000000-d3ffffff : VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
d5000000-d57fffff : S3 Inc. 86c764/765 [Trio32/64/64V+]
d5800000-d580007f : 3Com Corporation 3c905C-TX/TX-M [Tornado]
d5801000-d580107f : 3Com Corporation 3c905C-TX/TX-M [Tornado] (#2)
ffff0000-ffffffff : reserved
[7.5.]
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at c000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1a) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at c400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1a) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at c800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.5 Multimedia audio controller: VIA Technologies, Inc. AC97 Audio Controller (rev 50)
Subsystem: Micro-star International Co Ltd: Unknown device 3300
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 11
Region 0: I/O ports at cc00 [size=256]
Region 1: I/O ports at d000 [size=4]
Region 2: I/O ports at d400 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 VGA compatible controller: S3 Inc. 86c764/765 [Trio32/64/64V+] (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 12
Region 0: Memory at d5000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
00:09.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 74)
Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at dc00 [size=128]
Region 1: Memory at d5800000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:0a.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 74)
Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e000 [size=128]
Region 1: Memory at d5801000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
[7.6.] (though I don't have scsi physically)
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: LITE-ON Model: LTR-52246S Rev: 6S0D
Type: CD-ROM ANSI SCSI revision: 02
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/