Re: Patches for SCSI timeout bug

On Wed, Jun 04, 2003 at 11:44:43PM +0200, J.A. Magallon wrote:
> 
> On 06.04, [e-mail] wrote:
> > 
> > I've got a SCSI timeout bug in kernels 2.4 and 2.5, and several 
> > different patches (appended) that fix it.  I'm not sure which way 
> > of fixing it is best.
> > 
> 
> Can you try with this:
> 
> --- linux-2.4.18-18mdk/drivers/scsi/scsi_error.c.scsi-eh-timeout	Thu May 30 16:22:37 2002

OK, some more details:
-- you patch doesn't affect operation of the 'old' symbios driver, since
   it doesn't use the 'new' eh code. 

-- I tried the new (version 2) symbios driver w/ your patch.  It does
   allow the machine to boot, but it disables the cdrom. This is bad,
   because it prevents a booting from CDROM (e.g. for install).

   BTW, the v2 code doesn't hit your patches either; I put a printk
   in there and it never showed up ... 

To reiterate; my cdrom needs 15 seconds after a bus reset before it
will respond to a queueed command.  The v2 symbios driver doesn't wait
that long-- it just keeps reseting again, too quickly, which does no 
good.

Below are the boot msgs from the symbios v2 driver:
(my cdrom is at scsi id 4)

--linas

SCSI subsystem driver Revision: 1.00
PCI: Enabling device 00:0c.0 (0140 -> 0143)
sym.0.12.0: setting PCI_COMMAND_MASTER...
sym.0.12.0: setting PCI_COMMAND_INVALIDATE.
PCI: Enabling device 00:11.0 (0140 -> 0143)
sym.0.17.0: setting PCI_COMMAND_MASTER...
sym.0.17.0: setting PCI_COMMAND_INVALIDATE.
sym0: <875> rev 0x4 on pci bus 0 device 12 function 0 irq 17
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: SCSI BUS has been reset.
sym1: <895> rev 0x1 on pci bus 0 device 17 function 0 irq 20
sym1: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym1: SCSI BUS has been reset.
scsi0 : sym-2.1.17a
scsi1 : sym-2.1.17a
sym0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 15)
  Vendor: IBM       Model: DCHS04U           Rev: 2727
  Type:   Direct-Access                      ANSI SCSI revision: 02
sym0:4:0: ABORT operation started.
sym0:4:0: ABORT operation timed-out.
sym0:4:0: DEVICE RESET operation started.
sym0:4:0: DEVICE RESET operation complete.
sym0:4:control msgout: c.
sym0: TARGET 4 has been reset.
sym0:4:0: ABORT operation started.
sym0:4:0: ABORT operation complete.
sym0:4:0: BUS RESET operation started.
sym0:4:0: BUS RESET operation failed.
sym0:4:0: HOST RESET operation started.
sym0:4:0: HOST RESET operation failed.
scsi: device set offline - command error recover failed: host 0 channel 0 id 4 0sym0:9: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 16)
  Vendor: IBM       Model: DNES-309170W      Rev: SAGU
  Type:   Direct-Access                      ANSI SCSI revision: 03
sym0:0:0: tagged command queuing enabled, command queue depth 16.
sym0:9:0: tagged command queuing enabled, command queue depth 16.
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi disk sdb at scsi0, channel 0, id 9, lun 0
SCSI device sda: 8813870 512-byte hdwr sectors (4513 MB)
Partition check:
 sda: sda2 sda3 sda4
SCSI device sdb: 17774160 512-byte hdwr sectors (9100 MB)
 sdb: sdb1 sdb2 sdb3