I can't seem to get the onboard Serverworks CSB5 IDE controller (rev 93)
in a Compaq Proliant ML350 G3 to work (reliably/at all) no matter what
kernel I use:
o 2.4.21-rc6
intrerrupt timeouts, can't r/w from/to drive reliably in pio, dma hosed
o 2.4.21-rc2-ac3
r/w in pio ok, dma hosed
o 2.4.20
intrerrupt timeouts, can't r/w from/to drive reliably in pio, dma hosed
o 2.4.20-pre8-ac3 (has always worked on OSB4 beasts for me)
intrerrupt timeouts, can't r/w from/to drive reliably in pio, dma hosed
lspci & .config excerpts plus other bits of info follow.
The box is SMP + highmem.
--00:0f.1 IDE interface: ServerWorks CSB5 IDE Controller (rev 93) (prog-if 8a [Master SecP PriP]) Subsystem: ServerWorks CSB5 IDE Controller Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 0: I/O ports at <ignored> Region 1: I/O ports at <ignored> Region 2: I/O ports at <unassigned> Region 3: I/O ports at <unassigned> Region 4: I/O ports at 2000 [size=16]
CONFIG_IDE=y CONFIG_BLK_DEV_IDE=y # CONFIG_BLK_DEV_HD_IDE is not set # CONFIG_BLK_DEV_HD is not set CONFIG_BLK_DEV_IDEDISK=y # CONFIG_IDEDISK_MULTI_MODE is not set # CONFIG_IDEDISK_STROKE is not set # CONFIG_BLK_DEV_IDECS is not set CONFIG_BLK_DEV_IDECD=y # CONFIG_BLK_DEV_IDETAPE is not set # CONFIG_BLK_DEV_IDEFLOPPY is not set CONFIG_BLK_DEV_IDESCSI=y # CONFIG_IDE_TASK_IOCTL is not set # CONFIG_BLK_DEV_CMD640 is not set # CONFIG_BLK_DEV_CMD640_ENHANCED is not set # CONFIG_BLK_DEV_ISAPNP is not set CONFIG_BLK_DEV_IDEPCI=y CONFIG_BLK_DEV_GENERIC=y CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_BLK_DEV_IDEDMA_PCI=y # CONFIG_BLK_DEV_OFFBOARD is not set # CONFIG_BLK_DEV_IDEDMA_FORCED is not set CONFIG_IDEDMA_PCI_AUTO=y # CONFIG_IDEDMA_ONLYDISK is not set CONFIG_BLK_DEV_IDEDMA=y # CONFIG_IDEDMA_PCI_WIP is not set # CONFIG_BLK_DEV_ADMA100 is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_WDC_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set # CONFIG_AMD74XX_OVERRIDE is not set CONFIG_BLK_DEV_CMD64X=y # CONFIG_BLK_DEV_TRIFLEX is not set # CONFIG_BLK_DEV_CY82C693 is not set # CONFIG_BLK_DEV_CS5530 is not set # CONFIG_BLK_DEV_HPT34X is not set # CONFIG_HPT34X_AUTODMA is not set # CONFIG_BLK_DEV_HPT366 is not set # CONFIG_BLK_DEV_PIIX is not set # CONFIG_BLK_DEV_NS87415 is not set # CONFIG_BLK_DEV_OPTI621 is not set # CONFIG_BLK_DEV_PDC202XX_OLD is not set # CONFIG_PDC202XX_BURST is not set # CONFIG_BLK_DEV_PDC202XX_NEW is not set # CONFIG_BLK_DEV_RZ1000 is not set # CONFIG_BLK_DEV_SC1200 is not set CONFIG_BLK_DEV_SVWKS=y # CONFIG_BLK_DEV_SIIMAGE is not set # CONFIG_BLK_DEV_SIS5513 is not set # CONFIG_BLK_DEV_SLC90E66 is not set # CONFIG_BLK_DEV_TRM290 is not set # CONFIG_BLK_DEV_VIA82CXXX is not set # CONFIG_IDE_CHIPSETS is not set CONFIG_IDEDMA_AUTO=y # CONFIG_IDEDMA_IVB is not set # CONFIG_DMA_NONPCI is not set CONFIG_BLK_DEV_IDE_MODES=y # CONFIG_BLK_DEV_ATARAID is not set # CONFIG_BLK_DEV_ATARAID_PDC is not set # CONFIG_BLK_DEV_ATARAID_HPT is not set # CONFIG_BLK_DEV_ATARAID_SII is not set
(hdparm -Iv on 2.4.21-rc6) /dev/hdc: multcount = 16 (on) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 8 (on) geometry = 232581/16/63, sectors = 234441648, start = 0
ATA device, with non-removable media Model Number: WDC WD1200JB-00CRA1 Serial Number: WD-WCA8C4291018 Firmware Revision: 17.07W17 Standards: Supported: 5 4 3 2 Likely used: 6 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 234441648 device size with M = 1024*1024: 114473 MBytes device size with M = 1000*1000: 120034 MBytes (120 GB) Capabilities: LBA, IORDY(can be disabled) bytes avail on r/w long: 40 Queue depth: 1 Standby timer values: spec'd by Standard, with device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Recommended acoustic management value: 128, current value: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * READ BUFFER cmd * WRITE BUFFER cmd * Host Protected Area feature set * Look-ahead * Write cache * Power Management feature set Security Mode feature set * SMART feature set * Device Configuration Overlay feature set Automatic Acoustic Management feature set SET MAX security extension * DOWNLOAD MICROCODE cmd * SMART self-test * SMART error logging Security: supported not enabled not locked not frozen not expired: security count not supported: enhanced erase HW reset results: CBLID- above Vih Device num = 0 determined by CSEL Checksum: correct
(dmesg on 2.4.21-rc6) Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx SvrWks CSB5: IDE controller at PCI slot 00:0f.1 SvrWks CSB5: chipset revision 147 SvrWks CSB5: not 100% native mode: will probe irqs later SvrWks CSB5: simplex device: DMA forced ide0: BM-DMA at 0x2000-0x2007, BIOS settings: hda:pio, hdb:pio SvrWks CSB5: simplex device: DMA forced ide1: BM-DMA at 0x2008-0x200f, BIOS settings: hdc:pio, hdd:pio hda: LTN486S, ATAPI CD/DVD-ROM drive hda: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error } hda: set_drive_speed_status: error=0x04 hdc: WDC WD1200JB-00CRA1, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hdc: attached ide-disk driver. hdc: lost interrupt hdc: lost interrupt hdc: lost interrupt hdc: host protected area => 1 hdc: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=232581/16/63 hda: attached ide-cdrom driver. hda: ATAPI 48X CD-ROM drive, 120kB Cache Uniform CD-ROM driver Revision: 3.12 Partition check: hdc:<3>hdc: lost interrupt hdc: lost interrupt hdc: lost interrupt hdc: lost interrupt
-- Tomas Szepe <szepe@pinerecords.com> - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/