Re: ioctl cleanups: enable sg_io and serial stuff to be shared

[Arnd Bergmann]

On Wednesday 07 May 2003 14:41, Pavel Machek wrote:
> Hi!
>
> > > Only change *needed* in each architecture is moving A() macros into
> > > compat.h, so that generic code can use it. Please apply,
> >
> > Please don't use A() in new code, we now have compat_ptr() and
> > compat_uptr_t for this.
>
> Fixed now.

Ok. I now noticed there are some more problems that I did not see
at first:

> --- linux.clean/drivers/block/Makefile	2003-05-05 15:49:42.000000000 -0700
> +++ linux/drivers/block/Makefile	2003-05-06 13:53:24.000000000 -0700
> @@ -25,7 +25,7 @@
>  obj-$(CONFIG_BLK_DEV_PS2)	+= ps2esdi.o
>  obj-$(CONFIG_BLK_DEV_XD)	+= xd.o
>  obj-$(CONFIG_BLK_CPQ_DA)	+= cpqarray.o
> -obj-$(CONFIG_BLK_CPQ_CISS_DA)  += cciss.o
> +obj-$(CONFIG_BLK_CPQ_CISS_DA)	+= cciss.o
>  obj-$(CONFIG_BLK_DEV_DAC960)	+= DAC960.o

huh?

> +typedef struct sg_io_hdr32 {
> +	s32 interface_id;	/* [i] 'S' for SCSI generic (required) */
> +	s32 dxfer_direction;	/* [i] data transfer direction  */
> +	u8  cmd_len;		/* [i] SCSI command length ( <= 16 bytes) */
> +	u8  mx_sb_len;		/* [i] max length to write to sbp */
> +	u16 iovec_count;	/* [i] 0 implies no scatter gather */
> +	u32 dxfer_len;		/* [i] byte count of data transfer */
> +	u32 dxferp;		/* [i], [*io] points to data transfer memory
> +					      or scatter gather list */
> +	u32 cmdp;		/* [i], [*i] points to command to perform */
> +	u32 sbp;		/* [i], [*o] points to sense_buffer memory */
> +	u32 timeout;		/* [i] MAX_UINT->no timeout (unit: millisec) */
> +	u32 flags;		/* [i] 0 -> default, see SG_FLAG... */
> +	s32 pack_id;		/* [i->o] unused internally (normally) */
> +	u32 usr_ptr;		/* [i->o] unused internally */
> +	u8  status;		/* [o] scsi status */
> +	u8  masked_status;	/* [o] shifted, masked scsi status */
> +	u8  msg_status;		/* [o] messaging level data (optional) */
> +	u8  sb_len_wr;		/* [o] byte count actually written to sbp */
> +	u16 host_status;	/* [o] errors from host adapter */
> +	u16 driver_status;	/* [o] errors from software driver */
> +	s32 resid;		/* [o] dxfer_len - actual_transferred */
> +	u32 duration;		/* [o] time taken by cmd (unit: millisec) */
> +	u32 info;		/* [o] auxiliary information */
> +} sg_io_hdr32_t;  /* 64 bytes long (on sparc32) */
> +
> +typedef struct sg_iovec32 {
> +	u32 iov_base;
> +	u32 iov_len;
> +} sg_iovec32_t;

These should better be expressed with compat_uptr_t, compat_ulong_t etc.

> +	sg_iovec32_t *uiov = (sg_iovec32_t *) compat_ptr(uptr32);

> +		if (verify_area(VERIFY_WRITE, (void *)compat_ptr(iov_base32),
> kiov->iov_len)) +			return -EFAULT;
> +		kiov->iov_base = (void *)compat_ptr(iov_base32);

You don't need to cast to a pointer when using compat_ptr.

> +static int __init init_compat(void)
> +{
> +	register_ioctl32_conversion(SG_IO, sg_ioctl_trans);
> +	return 0;
> +}
> +
> +__initcall(init_compat);
> +#endif
> +
>  #define FORMAT_UNIT_TIMEOUT		(2 * 60 * 60 * HZ)
>  #define START_STOP_TIMEOUT		(60 * HZ)
>  #define MOVE_MEDIUM_TIMEOUT		(5 * 60 * HZ)

Has anyone solved the register_ioctl32_conversion() from module problem
yet? The patch will break if you build scsi as a module because you
never unregister the conversion helper on unload.
Even if you do the unregister from a module_exit() function, there
will still be a small race against running ioctl handlers. I suppose
we have to add an 'owner' field to struct ioctl_trans in order to
get it right.

> +#ifdef CONFIG_COMPAT
> +struct serial_struct32 {
> +	int	type;
> +	int	line;
> +	unsigned int	port;
> +	int	irq;
> +	int	flags;
> +	int	xmit_fifo_size;
> +	int	custom_divisor;
> +	int	baud_base;
> +	unsigned short	close_delay;
> +	char	io_type;
> +	char	reserved_char[1];
> +	int	hub6;
> +	unsigned short	closing_wait; /* time to wait before closing */
> +	unsigned short	closing_wait2; /* no longer used... */
> +	__u32 iomem_base;
> +	unsigned short	iomem_reg_shift;
> +	unsigned int	port_high;
> +	int	reserved[1];
> +};
see above.

> +		ss.iomem_base = (void *)((unsigned long)ss.iomem_base & 0xffffffff);
you need compat_ptr() for iomem_base as well

> +
> +static int __init init_compat(void)
> +{
> +	register_ioctl32_conversion(TIOCGSERIAL, serial_struct_ioctl);
> +	register_ioctl32_conversion(TIOCSSERIAL, serial_struct_ioctl);
> +	return 0;
> +}
> +
> +__initcall(init_compat);
see above.

	Arnd <><