--=_courier-29359-1049532085-0001-2
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
I tried booting my new Epox 8K9A3+ board with ACPI on, and while it
didn't crash, it also didn't work.
Small part of dmesg:
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
via-rhine.c:v1.10-LK1.1.17 March-1-2003 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
pci_link-0502 [23] acpi_pci_link_get_irq : Link disabled
pci_irq-0256 [22] acpi_pci_irq_lookup : Invalid IRQ link routing entry
pci_irq-0295 [22] acpi_pci_irq_derive : Unable to derive IRQ for device 00:12.0
ACPI: No IRQ known for interrupt pin A of device 00:12.0
eth0: VIA VT6102 Rhine-II at 0xde002000, 00:04:61:02:0e:ea, IRQ 5.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
It says it uses IRQ5, but it didn't - the network was dead.
I've attached a full dmesg of this box with and without acpi, and my
.config with acpi.
Kind regards,
Jurriaan
-- All I ask is a chance to prove that money can't make me happy. Debian (Unstable) GNU/Linux 2.5.66-mm3 3956 bogomips load av: 1.07 0.54 0.24--=_courier-29359-1049532085-0001-2 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Content-Disposition: attachment; filename="dmesg.acpi"
Linux version 2.5.66-mm3 (root@middle) (gcc version 3.2.3 20030331 (Debian prerelease)) #1 Sat Apr 5 08:02:11 CEST 2003 Video mode to be used for restore is f00 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009ec00 (usable) BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS) BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f5e60 hm, page 000f5000 reserved twice. hm, page 000f6000 reserved twice. hm, page 000f1000 reserved twice. hm, page 000f2000 reserved twice. On node 0 totalpages: 262128 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 225280 pages, LIFO batch:16 HighMem zone: 32752 pages, LIFO batch:7 ACPI: RSDP (v000 KT400 ) @ 0x000f7970 ACPI: RSDT (v001 KT400 AWRDACPI 16944.11825) @ 0x3fff3000 ACPI: FADT (v001 KT400 AWRDACPI 16944.11825) @ 0x3fff3040 ACPI: MADT (v001 KT400 AWRDACPI 16944.11825) @ 0x3fff7200 ACPI: DSDT (v001 KT400 AWRDACPI 00000.04096) @ 0x00000000 ACPI: BIOS passes blacklist ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:8 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0]) IOAPIC[0]: Assigned apic_id 2 IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, IRQ 0-23 ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0]) ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x0] trigger[0x0]) Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Building zonelist for node : 0 Kernel command line: root=/dev/hda1 video=matroxfb:vesa:0x11E,fv:85 hdb=scsi ide_setup: hdb=scsi Initializing CPU#0 PID hash table entries: 4096 (order 12: 32768 bytes) Detected 2004.476 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 3948.54 BogoMIPS Memory: 1032676k/1048512k available (2771k kernel code, 14892k reserved, 952k data, 420k init, 131008k highmem) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) -> /dev -> /dev/console -> /root CPU: CLK_CTL MSR was 60031223. Reprogramming to 20031223 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Machine check exception polling timer started. CPU: AMD Athlon(tm) XP 2400+ stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 number of MP IRQ sources: 16. number of IO-APIC #2 registers: 24. testing the IO APIC.......................
IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178003 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0003 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 0 0 0 0 0 1 1 71 0a 001 01 0 0 0 0 0 1 1 79 0b 001 01 0 0 0 0 0 1 1 81 0c 001 01 0 0 0 0 0 1 1 89 0d 001 01 0 0 0 0 0 1 1 91 0e 001 01 0 0 0 0 0 1 1 99 0f 001 01 0 0 0 0 0 1 1 A1 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2004.0201 MHz. ..... host bus clock speed is 267.0226 MHz. Initializing RT netlink socket mtrr: v2.0 (20020519) PCI: PCI BIOS revision 2.10 entry at 0xfb350, last bus=1 PCI: Using configuration type 1 BIO: pool of 256 setup, 14Kb (56 bytes/bio) biovec pool[0]: 1 bvecs: 256 entries (12 bytes) biovec pool[1]: 4 bvecs: 256 entries (48 bytes) biovec pool[2]: 16 bvecs: 256 entries (192 bytes) biovec pool[3]: 64 bvecs: 256 entries (768 bytes) biovec pool[4]: 128 bvecs: 256 entries (1536 bytes) biovec pool[5]: 256 bvecs: 256 entries (3072 bytes) ACPI: Subsystem revision 20030328 tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully acquired Parsing all Control Methods:........................................................................................................................................... Table [DSDT] - 517 Objects with 48 Devices 139 Methods 28 Regions ACPI Namespace successfully loaded at root c053155c evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode successful evgpeblk-0731 [06] ev_create_gpe_block : GPE Block: [_GPE] 2 registers at 0000000000004020 on interrupt 9 evgpeblk-0736 [06] ev_create_gpe_block : GPE Block defined as GPE 0x00 to GPE 0x0F evgpeblk-0262 [07] ev_save_method_info : Registered GPE method _L03 as GPE number 0x03 evgpeblk-0262 [07] ev_save_method_info : Registered GPE method _L05 as GPE number 0x05 evgpeblk-0262 [07] ev_save_method_info : Registered GPE method _L08 as GPE number 0x08 evgpeblk-0262 [07] ev_save_method_info : Registered GPE method _L09 as GPE number 0x09 evgpeblk-0262 [07] ev_save_method_info : Registered GPE method _L0E as GPE number 0x0E evgpeblk-0262 [07] ev_save_method_info : Registered GPE method _L0A as GPE number 0x0A Executing all Device _STA and_INI methods:................................................ 48 Devices found containing: 48 _STA, 2 _INI methods Completing Region/Field/Buffer/Package initialization:....................................................................... Initialized 23/28 Regions 11/13 Fields 19/20 Buffers 18/18 Packages (517 nodes) ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15) pci_link-0256 [17] acpi_pci_link_get_curr: No IRQ resource found ACPI: PCI Interrupt Link [ALKA] (IRQs 20, disabled) pci_link-0256 [19] acpi_pci_link_get_curr: No IRQ resource found ACPI: PCI Interrupt Link [ALKB] (IRQs 21, disabled) pci_link-0256 [21] acpi_pci_link_get_curr: No IRQ resource found ACPI: PCI Interrupt Link [ALKC] (IRQs 22, disabled) pci_link-0256 [23] acpi_pci_link_get_curr: No IRQ resource found ACPI: PCI Interrupt Link [ALKD] (IRQs 23, disabled) block request queues: 128 requests per read queue 128 requests per write queue 8 requests per batch enter congestion at 15 exit congestion at 17 SCSI subsystem initialized drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub pci_link-0256 [21] acpi_pci_link_get_curr: No IRQ resource found ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 0 pci_link-0256 [22] acpi_pci_link_get_curr: No IRQ resource found ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 0 pci_link-0256 [23] acpi_pci_link_get_curr: No IRQ resource found ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 0 pci_link-0256 [24] acpi_pci_link_get_curr: No IRQ resource found ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 0 IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16) 00:00:08[A] -> 2-16 -> IRQ 16 IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17) 00:00:08[B] -> 2-17 -> IRQ 17 IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb9 -> IRQ 18) 00:00:08[C] -> 2-18 -> IRQ 18 IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19) 00:00:08[D] -> 2-19 -> IRQ 19 Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed pci_link-0502 [24] acpi_pci_link_get_irq : Link disabled pci_irq-0256 [23] acpi_pci_irq_lookup : Invalid IRQ link routing entry pci_irq-0295 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:10.0 ACPI: No IRQ known for interrupt pin A of device 00:10.0 pci_link-0502 [24] acpi_pci_link_get_irq : Link disabled pci_irq-0256 [23] acpi_pci_irq_lookup : Invalid IRQ link routing entry pci_irq-0295 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:10.1 ACPI: No IRQ known for interrupt pin B of device 00:10.1 pci_link-0502 [24] acpi_pci_link_get_irq : Link disabled pci_irq-0256 [23] acpi_pci_irq_lookup : Invalid IRQ link routing entry pci_irq-0295 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:10.2 ACPI: No IRQ known for interrupt pin C of device 00:10.2 pci_link-0502 [24] acpi_pci_link_get_irq : Link disabled pci_irq-0256 [23] acpi_pci_irq_lookup : Invalid IRQ link routing entry pci_irq-0295 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:11.1 ACPI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255 pci_link-0502 [24] acpi_pci_link_get_irq : Link disabled pci_irq-0256 [23] acpi_pci_irq_lookup : Invalid IRQ link routing entry pci_irq-0295 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:11.5 ACPI: No IRQ known for interrupt pin C of device 00:11.5 pci_link-0502 [24] acpi_pci_link_get_irq : Link disabled pci_irq-0256 [23] acpi_pci_irq_lookup : Invalid IRQ link routing entry pci_irq-0295 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:12.0 ACPI: No IRQ known for interrupt pin A of device 00:12.0 PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' Enabling SEP on CPU 0 highmem bounce pool size: 64 pages Journalled Block Device driver loaded NTFS driver 2.1.0 [Flags: R/O]. udf: registering filesystem ACPI: Power Button (FF) [PWRF] ACPI: Fan [FAN] (on) ACPI: Processor [CPU0] (supports C1 C2) ACPI: Thermal Zone [THRM] (39 C) matroxfb: Matrox G450 detected matroxfb: MTRR's turned on matroxfb: 1600x1200x16bpp (virtual: 1600x5241) matroxfb: framebuffer at 0xD8000000, mapped to 0xf8811000, size 33554432 Console: switching to colour frame buffer device 133x54 fb0: MATROX VGA frame buffer device pty: 256 Unix98 ptys configured request_module: failed /sbin/modprobe -- parport_lowlevel. error = -16 lp: driver loaded but no devices found Real Time Clock Driver v1.11 Software Watchdog Timer: 0.06, soft_margin: 60 sec, nowayout: 0 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected VIA Apollo Pro KT400 chipset agpgart: Maximum main memory to use for agp memory: 941M agpgart: AGP aperture is 128M @ 0xd0000000 [drm] AGP 0.100 aperture @ 0xd0000000 128MB [drm] Initialized mga 3.1.0 20021029 on minor 0 Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A parport0: PC-style at 0x378 [PCSPP,TRISTATE] parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) lp0: using parport0 (polling). anticipatory scheduling elevator Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) via-rhine.c:v1.10-LK1.1.17 March-1-2003 Written by Donald Becker http://www.scyld.com/network/via-rhine.html pci_link-0502 [23] acpi_pci_link_get_irq : Link disabled pci_irq-0256 [22] acpi_pci_irq_lookup : Invalid IRQ link routing entry pci_irq-0295 [22] acpi_pci_irq_derive : Unable to derive IRQ for device 00:12.0 ACPI: No IRQ known for interrupt pin A of device 00:12.0 eth0: VIA VT6102 Rhine-II at 0xde002000, 00:04:61:02:0e:ea, IRQ 5. eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx HPT374: IDE controller at PCI slot 00:0e.0 HPT374: chipset revision 7 HPT374: not 100% native mode: will probe irqs later HPT37X: using 33MHz PCI clock ide2: BM-DMA at 0xbc00-0xbc07, BIOS settings: hde:DMA, hdf:pio ide3: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdg:pio, hdh:pio HPT37X: using 33MHz PCI clock ide4: BM-DMA at 0xd000-0xd007, BIOS settings: hdi:DMA, hdj:pio ide5: BM-DMA at 0xd008-0xd00f, BIOS settings: hdk:pio, hdl:pio hde: WDC WD800JB-00CRA1, ATA DISK drive anticipatory scheduling elevator ide2 at 0xac00-0xac07,0xb002 on irq 17 hdi: WDC WD800JB-00CRA1, ATA DISK drive anticipatory scheduling elevator ide4 at 0xc000-0xc007,0xc402 on irq 17 VP_IDE: IDE controller at PCI slot 00:11.1 pci_link-0502 [23] acpi_pci_link_get_irq : Link disabled pci_irq-0256 [22] acpi_pci_irq_lookup : Invalid IRQ link routing entry pci_irq-0295 [22] acpi_pci_irq_derive : Unable to derive IRQ for device 00:11.1 ACPI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1 ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA hda: IBM-DTLA-307045, ATA DISK drive hdb: LITE-ON LTR-40125W, ATAPI CD/DVD-ROM drive anticipatory scheduling elevator anticipatory scheduling elevator ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: Maxtor 4G120J6, ATA DISK drive hdd: Maxtor 4G120J6, ATA DISK drive anticipatory scheduling elevator anticipatory scheduling elevator ide1 at 0x170-0x177,0x376 on irq 15 hde: host protected area => 1 hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(100) hde: hde1 hde2 hdi: host protected area => 1 hdi: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(100) hdi: hdi1 hdi2 hda: host protected area => 1 hda: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=89355/16/63, UDMA(100) hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 > hdc: host protected area => 1 hdc: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=14946/255/63, UDMA(133) hdc: hdc1 hdc2 hdd: host protected area => 1 hdd: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=14946/255/63, UDMA(133) hdd: hdd1 hdd2 ide-cd: passing drive hdb to ide-scsi emulation. scsi HBA driver sym53c8xx didn't set a release method, please fix the template sym.0.10.0: setting PCI_COMMAND_PARITY... sym.0.10.0: setting PCI_COMMAND_INVALIDATE. sym0: <860> rev 0x13 on pci bus 0 device 10 function 0 irq 18 sym0: No NVRAM, ID 7, Fast-20, SE, parity checking sym0: SCSI BUS has been reset. scsi0 : sym-2.1.16a anticipatory scheduling elevator Vendor: TOSHIBA Model: DVD-ROM SD-M1401 Rev: 1007 Type: CD-ROM ANSI SCSI revision: 02 anticipatory scheduling elevator Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02 Type: CD-ROM ANSI SCSI revision: 02 anticipatory scheduling elevator Vendor: YAMAHA Model: CRW2100S Rev: 1.0N Type: CD-ROM ANSI SCSI revision: 02 anticipatory scheduling elevator scsi1 : SCSI host adapter emulation for IDE ATAPI devices anticipatory scheduling elevator Vendor: LITE-ON Model: LTR-40125W Rev: WS05 Type: CD-ROM ANSI SCSI revision: 02 st: Version 20021214, fixed bufsize 32768, wrt 30720, s/g segs 256 sym0:1: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 8) sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12 Attached scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0 sym0:2: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 8) sr1: scsi-1 drive Attached scsi CD-ROM sr1 at scsi0, channel 0, id 2, lun 0 sym0:5: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 7) sr2: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray Attached scsi CD-ROM sr2 at scsi0, channel 0, id 5, lun 0 sr3: scsi3-mmc drive: 255x/48x writer cd/rw xa/form2 cdda tray Attached scsi CD-ROM sr3 at scsi1, channel 0, id 0, lun 0 Internal inconsistency: unsupported color depth 0 on CRTC2 matroxfb_crtc2: secondary head of fb0 was registered as fb1 drivers/usb/core/usb.c: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver drivers/usb/core/usb.c: registered new driver usbscanner drivers/usb/image/scanner.c: 0.4.11:USB Scanner Driver mice: PS/2 mouse device common for all mice input: PC Speaker input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 serio: i8042 AUX port at 0x60,0x64 irq 12 input: AT Set 2 keyboard on isa0060/serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 2688.000 MB/sec 8regs_prefetch: 2752.000 MB/sec 32regs : 1984.000 MB/sec 32regs_prefetch: 1796.000 MB/sec pIII_sse : 5340.000 MB/sec pII_mmx : 5308.000 MB/sec p5_mmx : 7056.000 MB/sec raid5: using function: pIII_sse (5340.000 MB/sec) md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 Advanced Linux Sound Architecture Driver Version 0.9.2 (Thu Mar 20 13:31:57 2003 UTC). request_module: failed /sbin/modprobe -- snd-card-0. error = -16 pci_link-0502 [23] acpi_pci_link_get_irq : Link disabled pci_irq-0256 [22] acpi_pci_irq_lookup : Invalid IRQ link routing entry pci_irq-0295 [22] acpi_pci_irq_derive : Unable to derive IRQ for device 00:11.5 ACPI: No IRQ known for interrupt pin C of device 00:11.5 PCI: Setting latency timer of device 00:11.5 to 64 ALSA device list: #0: VIA 8235 at 0xe400, irq 11 #1: Sound Blaster Live! (rev.7) at 0xa400, irq 19 NET4: Linux TCP/IP 1.0 for NET4.0 IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. md: Autodetecting RAID arrays. md: autorun ... md: considering hdi2 ... md: adding hdi2 ... md: hdi1 has different UUID to hdi2 md: adding hde2 ... md: hde1 has different UUID to hdi2 md: created md1 md: bind<hde2> md: bind<hdi2> md: running: <hdi2><hde2> md1: max total readahead window set to 512k md1: 2 data-disks, max readahead per data-disk: 256k md1: setting max_sectors to 128, segment boundary to 32767 raid0: looking at hdi2 raid0: comparing hdi2(17670656) with hdi2(17670656) raid0: END raid0: ==> UNIQUE raid0: 1 zones raid0: looking at hde2 raid0: comparing hde2(17670656) with hdi2(17670656) raid0: EQUAL raid0: FINAL 1 zones raid0: done. raid0 : md_size is 35341312 blocks. raid0 : conf->smallest->size is 35341312 blocks. raid0 : nb_zone is 1. raid0 : Allocating 8 bytes for hash. md: considering hdi1 ... md: adding hdi1 ... md: adding hde1 ... md: created md0 md: bind<hde1> md: bind<hdi1> md: running: <hdi1><hde1> md0: max total readahead window set to 512k md0: 2 data-disks, max readahead per data-disk: 256k md0: setting max_sectors to 128, segment boundary to 32767 raid0: looking at hdi1 raid0: comparing hdi1(60479872) with hdi1(60479872) raid0: END raid0: ==> UNIQUE raid0: 1 zones raid0: looking at hde1 raid0: comparing hde1(60479872) with hdi1(60479872) raid0: EQUAL raid0: FINAL 1 zones raid0: done. raid0 : md_size is 120959744 blocks. raid0 : conf->smallest->size is 120959744 blocks. raid0 : nb_zone is 1. raid0 : Allocating 8 bytes for hash. md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 420k freed Adding 2000368k swap on /dev/hda3. Priority:-1 extents:1 EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide0(3,1), internal journal nvidia: module license 'NVIDIA' taints kernel. 0: nvidia: no NVIDIA graphics adapter found kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide0(3,2), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide0(3,7), internal journal EXT3-fs: mounted filesystem with ordered data mode. found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide0(3,8), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide0(3,8)) for (ide0(3,8)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide0(3,6), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide0(3,6)) for (ide0(3,6)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide0(3,5), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide0(3,5)) for (ide0(3,5)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide0(3,10), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide0(3,10)) for (ide0(3,10)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device md(9,0), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (md(9,0)) for (md(9,0)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device md(9,1), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (md(9,1)) for (md(9,1)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide1(22,1), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide1(22,1)) for (ide1(22,1)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide1(22,2), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide1(22,2)) for (ide1(22,2)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide1(22,65), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide1(22,65)) for (ide1(22,65)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide1(22,66), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide1(22,66)) for (ide1(22,66)) Using r5 hash to sort names eth0: Setting full-duplex based on MII #1 link partner capability of 45e1. NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timed out, status 0003, PHY status 786d, resetting... eth0: Setting full-duplex based on MII #1 link partner capability of 45e1. NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timed out, status 0003, PHY status 786d, resetting... eth0: Setting full-duplex based on MII #1 link partner capability of 45e1. NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timed out, status 0003, PHY status 786d, resetting... eth0: Setting full-duplex based on MII #1 link partner capability of 45e1. NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timed out, status 0003, PHY status 786d, resetting... eth0: Setting full-duplex based on MII #1 link partner capability of 45e1. NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timed out, status 0003, PHY status 786d, resetting... eth0: Setting full-duplex based on MII #1 link partner capability of 45e1. NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timed out, status 0003, PHY status 786d, resetting... eth0: Setting full-duplex based on MII #1 link partner capability of 45e1. NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timed out, status 0003, PHY status 786d, resetting... eth0: Setting full-duplex based on MII #1 link partner capability of 45e1. NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timed out, status 0003, PHY status 786d, resetting... eth0: Setting full-duplex based on MII #1 link partner capability of 45e1. NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timed out, status 0003, PHY status 786d, resetting... eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
--=_courier-29359-1049532085-0001-2 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Content-Disposition: attachment; filename="dmesg.normal"
Linux version 2.5.66-mm3 (root@middle) (gcc version 3.2.3 20030331 (Debian prerelease)) #1 Fri Apr 4 18:53:08 CEST 2003 Video mode to be used for restore is f00 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009ec00 (usable) BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS) BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f5e60 hm, page 000f5000 reserved twice. hm, page 000f6000 reserved twice. hm, page 000f1000 reserved twice. hm, page 000f2000 reserved twice. On node 0 totalpages: 262128 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 225280 pages, LIFO batch:16 HighMem zone: 32752 pages, LIFO batch:7 Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000 Processor #0 6:8 APIC version 17 I/O APIC #2 Version 17 at 0xFEC00000. Enabling APIC mode: Flat. Using 1 I/O APICs Processors: 1 Building zonelist for node : 0 Kernel command line: root=/dev/hda1 video=matroxfb:vesa:0x11E,fv:85 hdb=scsi ide_setup: hdb=scsi Initializing CPU#0 PID hash table entries: 4096 (order 12: 32768 bytes) Detected 2004.476 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 3956.73 BogoMIPS Memory: 1032984k/1048512k available (2575k kernel code, 14584k reserved, 852k data, 412k init, 131008k highmem) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) -> /dev -> /dev/console -> /root CPU: CLK_CTL MSR was 60031223. Reprogramming to 20031223 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Machine check exception polling timer started. CPU: AMD Athlon(tm) XP 2400+ stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs Setting 2 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 2 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-20 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 number of MP IRQ sources: 23. number of IO-APIC #2 registers: 24. testing the IO APIC.......................
IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178003 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0003 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 000 00 1 0 0 0 0 0 0 00 06 001 01 0 0 0 0 0 1 1 51 07 001 01 0 0 0 0 0 1 1 59 08 001 01 0 0 0 0 0 1 1 61 09 001 01 0 0 0 0 0 1 1 69 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 001 01 0 0 0 0 0 1 1 71 0d 001 01 0 0 0 0 0 1 1 79 0e 001 01 0 0 0 0 0 1 1 81 0f 001 01 0 0 0 0 0 1 1 89 10 001 01 1 1 0 1 0 1 1 91 11 001 01 1 1 0 1 0 1 1 99 12 001 01 1 1 0 1 0 1 1 A1 13 001 01 1 1 0 1 0 1 1 A9 14 000 00 1 0 0 0 0 0 0 00 15 001 01 1 1 0 1 0 1 1 B1 16 001 01 1 1 0 1 0 1 1 B9 17 001 01 1 1 0 1 0 1 1 C1 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 0:16 IRQ17 -> 0:17 IRQ18 -> 0:18 IRQ19 -> 0:19 IRQ21 -> 0:21 IRQ22 -> 0:22 IRQ23 -> 0:23 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2004.0201 MHz. ..... host bus clock speed is 267.0226 MHz. Initializing RT netlink socket mtrr: v2.0 (20020519) PCI: PCI BIOS revision 2.10 entry at 0xfb350, last bus=1 PCI: Using configuration type 1 BIO: pool of 256 setup, 14Kb (56 bytes/bio) biovec pool[0]: 1 bvecs: 256 entries (12 bytes) biovec pool[1]: 4 bvecs: 256 entries (48 bytes) biovec pool[2]: 16 bvecs: 256 entries (192 bytes) biovec pool[3]: 64 bvecs: 256 entries (768 bytes) biovec pool[4]: 128 bvecs: 256 entries (1536 bytes) biovec pool[5]: 256 bvecs: 256 entries (3072 bytes) block request queues: 128 requests per read queue 128 requests per write queue 8 requests per batch enter congestion at 15 exit congestion at 17 SCSI subsystem initialized drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Using IRQ router VIA [1106/3177] at 00:11.0 PCI->APIC IRQ transform: (B1,I0,P0) -> 16 PCI->APIC IRQ transform: (B0,I10,P0) -> 18 PCI->APIC IRQ transform: (B0,I13,P0) -> 19 PCI->APIC IRQ transform: (B0,I14,P0) -> 17 PCI->APIC IRQ transform: (B0,I14,P0) -> 17 PCI->APIC IRQ transform: (B0,I16,P0) -> 21 PCI->APIC IRQ transform: (B0,I16,P1) -> 21 PCI->APIC IRQ transform: (B0,I16,P2) -> 21 PCI->APIC IRQ transform: (B0,I17,P0) -> 22 PCI->APIC IRQ transform: (B0,I17,P2) -> 22 PCI->APIC IRQ transform: (B0,I18,P0) -> 23 apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) Enabling SEP on CPU 0 highmem bounce pool size: 64 pages Journalled Block Device driver loaded NTFS driver 2.1.0 [Flags: R/O]. udf: registering filesystem PCI: Via IRQ fixup for 00:10.1, from 10 to 5 PCI: Via IRQ fixup for 00:10.2, from 11 to 5 matroxfb: Matrox G450 detected matroxfb: MTRR's turned on matroxfb: 1600x1200x16bpp (virtual: 1600x5241) matroxfb: framebuffer at 0xD8000000, mapped to 0xf8805000, size 33554432 Console: switching to colour frame buffer device 133x54 fb0: MATROX VGA frame buffer device pty: 256 Unix98 ptys configured request_module: failed /sbin/modprobe -- parport_lowlevel. error = -16 lp: driver loaded but no devices found Real Time Clock Driver v1.11 Software Watchdog Timer: 0.06, soft_margin: 60 sec, nowayout: 0 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected VIA Apollo Pro KT400 chipset agpgart: Maximum main memory to use for agp memory: 941M agpgart: AGP aperture is 128M @ 0xd0000000 [drm] AGP 0.100 aperture @ 0xd0000000 128MB [drm] Initialized mga 3.1.0 20021029 on minor 0 Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A parport0: PC-style at 0x378 [PCSPP,TRISTATE] parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) lp0: using parport0 (polling). anticipatory scheduling elevator Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) via-rhine.c:v1.10-LK1.1.17 March-1-2003 Written by Donald Becker http://www.scyld.com/network/via-rhine.html eth0: VIA VT6102 Rhine-II at 0xde002000, 00:04:61:02:0e:ea, IRQ 23. eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx HPT374: IDE controller at PCI slot 00:0e.0 HPT374: chipset revision 7 HPT374: not 100% native mode: will probe irqs later HPT37X: using 33MHz PCI clock ide2: BM-DMA at 0xbc00-0xbc07, BIOS settings: hde:DMA, hdf:pio ide3: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdg:pio, hdh:pio HPT37X: using 33MHz PCI clock ide4: BM-DMA at 0xd000-0xd007, BIOS settings: hdi:DMA, hdj:pio ide5: BM-DMA at 0xd008-0xd00f, BIOS settings: hdk:pio, hdl:pio hde: WDC WD800JB-00CRA1, ATA DISK drive anticipatory scheduling elevator ide2 at 0xac00-0xac07,0xb002 on irq 17 hdi: WDC WD800JB-00CRA1, ATA DISK drive anticipatory scheduling elevator ide4 at 0xc000-0xc007,0xc402 on irq 17 VP_IDE: IDE controller at PCI slot 00:11.1 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1 ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA hda: IBM-DTLA-307045, ATA DISK drive hdb: LITE-ON LTR-40125W, ATAPI CD/DVD-ROM drive anticipatory scheduling elevator anticipatory scheduling elevator ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: Maxtor 4G120J6, ATA DISK drive hdd: Maxtor 4G120J6, ATA DISK drive anticipatory scheduling elevator anticipatory scheduling elevator ide1 at 0x170-0x177,0x376 on irq 15 hde: host protected area => 1 hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(100) hde: hde1 hde2 hdi: host protected area => 1 hdi: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(100) hdi: hdi1 hdi2 hda: host protected area => 1 hda: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=89355/16/63, UDMA(100) hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 > hdc: host protected area => 1 hdc: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=14946/255/63, UDMA(133) hdc: hdc1 hdc2 hdd: host protected area => 1 hdd: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=14946/255/63, UDMA(133) hdd: hdd1 hdd2 ide-cd: passing drive hdb to ide-scsi emulation. scsi HBA driver sym53c8xx didn't set a release method, please fix the template sym.0.10.0: setting PCI_COMMAND_PARITY... sym.0.10.0: setting PCI_COMMAND_INVALIDATE. sym0: <860> rev 0x13 on pci bus 0 device 10 function 0 irq 18 sym0: No NVRAM, ID 7, Fast-20, SE, parity checking sym0: SCSI BUS has been reset. scsi0 : sym-2.1.16a anticipatory scheduling elevator Vendor: TOSHIBA Model: DVD-ROM SD-M1401 Rev: 1007 Type: CD-ROM ANSI SCSI revision: 02 anticipatory scheduling elevator Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02 Type: CD-ROM ANSI SCSI revision: 02 anticipatory scheduling elevator Vendor: YAMAHA Model: CRW2100S Rev: 1.0N Type: CD-ROM ANSI SCSI revision: 02 anticipatory scheduling elevator scsi1 : SCSI host adapter emulation for IDE ATAPI devices anticipatory scheduling elevator Vendor: LITE-ON Model: LTR-40125W Rev: WS05 Type: CD-ROM ANSI SCSI revision: 02 st: Version 20021214, fixed bufsize 32768, wrt 30720, s/g segs 256 sym0:1: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 8) sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12 Attached scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0 sym0:2: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 8) sr1: scsi-1 drive Attached scsi CD-ROM sr1 at scsi0, channel 0, id 2, lun 0 sym0:5: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 7) sr2: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray Attached scsi CD-ROM sr2 at scsi0, channel 0, id 5, lun 0 sr3: scsi3-mmc drive: 255x/48x writer cd/rw xa/form2 cdda tray Attached scsi CD-ROM sr3 at scsi1, channel 0, id 0, lun 0 Internal inconsistency: unsupported color depth 0 on CRTC2 matroxfb_crtc2: secondary head of fb0 was registered as fb1 drivers/usb/core/usb.c: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver drivers/usb/core/usb.c: registered new driver usbscanner drivers/usb/image/scanner.c: 0.4.11:USB Scanner Driver mice: PS/2 mouse device common for all mice input: PC Speaker input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 serio: i8042 AUX port at 0x60,0x64 irq 12 input: AT Set 2 keyboard on isa0060/serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 3028.000 MB/sec 8regs_prefetch: 2756.000 MB/sec 32regs : 2012.000 MB/sec 32regs_prefetch: 1804.000 MB/sec pIII_sse : 5336.000 MB/sec pII_mmx : 5308.000 MB/sec p5_mmx : 7056.000 MB/sec raid5: using function: pIII_sse (5336.000 MB/sec) md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 Advanced Linux Sound Architecture Driver Version 0.9.2 (Thu Mar 20 13:31:57 2003 UTC). request_module: failed /sbin/modprobe -- snd-card-0. error = -16 PCI: Setting latency timer of device 00:11.5 to 64 ALSA device list: #0: VIA 8235 at 0xe400, irq 22 #1: Sound Blaster Live! (rev.7) at 0xa400, irq 19 NET4: Linux TCP/IP 1.0 for NET4.0 IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. md: Autodetecting RAID arrays. md: autorun ... md: considering hdi2 ... md: adding hdi2 ... md: hdi1 has different UUID to hdi2 md: adding hde2 ... md: hde1 has different UUID to hdi2 md: created md1 md: bind<hde2> md: bind<hdi2> md: running: <hdi2><hde2> md1: max total readahead window set to 512k md1: 2 data-disks, max readahead per data-disk: 256k md1: setting max_sectors to 128, segment boundary to 32767 raid0: looking at hdi2 raid0: comparing hdi2(17670656) with hdi2(17670656) raid0: END raid0: ==> UNIQUE raid0: 1 zones raid0: looking at hde2 raid0: comparing hde2(17670656) with hdi2(17670656) raid0: EQUAL raid0: FINAL 1 zones raid0: done. raid0 : md_size is 35341312 blocks. raid0 : conf->smallest->size is 35341312 blocks. raid0 : nb_zone is 1. raid0 : Allocating 8 bytes for hash. md: considering hdi1 ... md: adding hdi1 ... md: adding hde1 ... md: created md0 md: bind<hde1> md: bind<hdi1> md: running: <hdi1><hde1> md0: max total readahead window set to 512k md0: 2 data-disks, max readahead per data-disk: 256k md0: setting max_sectors to 128, segment boundary to 32767 raid0: looking at hdi1 raid0: comparing hdi1(60479872) with hdi1(60479872) raid0: END raid0: ==> UNIQUE raid0: 1 zones raid0: looking at hde1 raid0: comparing hde1(60479872) with hdi1(60479872) raid0: EQUAL raid0: FINAL 1 zones raid0: done. raid0 : md_size is 120959744 blocks. raid0 : conf->smallest->size is 120959744 blocks. raid0 : nb_zone is 1. raid0 : Allocating 8 bytes for hash. md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 412k freed Adding 2000368k swap on /dev/hda3. Priority:-1 extents:1 EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide0(3,1), internal journal nvidia: module license 'NVIDIA' taints kernel. 0: nvidia: no NVIDIA graphics adapter found kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide0(3,2), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide0(3,7), internal journal EXT3-fs: mounted filesystem with ordered data mode. found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide0(3,8), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide0(3,8)) for (ide0(3,8)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide0(3,6), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide0(3,6)) for (ide0(3,6)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide0(3,5), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide0(3,5)) for (ide0(3,5)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide0(3,10), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide0(3,10)) for (ide0(3,10)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device md(9,0), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (md(9,0)) for (md(9,0)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device md(9,1), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (md(9,1)) for (md(9,1)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide1(22,1), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide1(22,1)) for (ide1(22,1)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide1(22,2), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide1(22,2)) for (ide1(22,2)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide1(22,65), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide1(22,65)) for (ide1(22,65)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide1(22,66), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide1(22,66)) for (ide1(22,66)) Using r5 hash to sort names eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
--=_courier-29359-1049532085-0001-2 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Content-Disposition: attachment; filename="config.acpi"
CONFIG_X86=y CONFIG_MMU=y CONFIG_UID16=y CONFIG_GENERIC_ISA_DMA=y CONFIG_EXPERIMENTAL=y CONFIG_SWAP=y CONFIG_SYSVIPC=y CONFIG_SYSCTL=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y CONFIG_OBSOLETE_MODPARM=y CONFIG_KMOD=y CONFIG_X86_PC=y CONFIG_MK7=y CONFIG_X86_CMPXCHG=y CONFIG_X86_XADD=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_X86_WP_WORKS_OK=y CONFIG_X86_INVLPG=y CONFIG_X86_BSWAP=y CONFIG_X86_POPAD_OK=y CONFIG_X86_GOOD_APIC=y CONFIG_X86_USE_PPRO_CHECKSUM=y CONFIG_X86_USE_3DNOW=y CONFIG_PREEMPT=y CONFIG_X86_UP_APIC=y CONFIG_X86_UP_IOAPIC=y CONFIG_X86_LOCAL_APIC=y CONFIG_X86_IO_APIC=y CONFIG_X86_TSC=y CONFIG_X86_MCE=y CONFIG_X86_MCE_NONFATAL=y CONFIG_HIGHMEM4G=y CONFIG_1GB=y CONFIG_HIGHMEM=y CONFIG_HIGHPTE=y CONFIG_MTRR=y CONFIG_HAVE_DEC_LOCK=y CONFIG_PM=y CONFIG_ACPI=y CONFIG_ACPI_BOOT=y CONFIG_ACPI_BUTTON=y CONFIG_ACPI_FAN=y CONFIG_ACPI_PROCESSOR=y CONFIG_ACPI_THERMAL=y CONFIG_ACPI_DEBUG=y CONFIG_ACPI_BUS=y CONFIG_ACPI_INTERPRETER=y CONFIG_ACPI_EC=y CONFIG_ACPI_POWER=y CONFIG_ACPI_PCI=y CONFIG_ACPI_SYSTEM=y CONFIG_PCI=y CONFIG_PCI_GOANY=y CONFIG_PCI_BIOS=y CONFIG_PCI_DIRECT=y CONFIG_PCI_NAMES=y CONFIG_ISA=y CONFIG_KCORE_ELF=y CONFIG_BINFMT_AOUT=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_PARPORT=y CONFIG_PARPORT_PC=y CONFIG_PARPORT_PC_CML1=y CONFIG_PARPORT_1284=y CONFIG_BLK_DEV_FD=y CONFIG_BLK_DEV_LOOP=y CONFIG_IDE=y CONFIG_BLK_DEV_IDE=y CONFIG_BLK_DEV_IDEDISK=y CONFIG_BLK_DEV_IDECD=y CONFIG_BLK_DEV_IDESCSI=y CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_BLK_DEV_IDEDMA_PCI=y CONFIG_IDEDMA_PCI_AUTO=y CONFIG_BLK_DEV_IDEDMA=y CONFIG_BLK_DEV_ADMA=y CONFIG_BLK_DEV_AMD74XX=y CONFIG_BLK_DEV_HPT366=y CONFIG_BLK_DEV_PDC202XX_OLD=y CONFIG_BLK_DEV_VIA82CXXX=y CONFIG_IDEDMA_AUTO=y CONFIG_BLK_DEV_PDC202XX=y CONFIG_BLK_DEV_IDE_MODES=y CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y CONFIG_CHR_DEV_ST=y CONFIG_BLK_DEV_SR=y CONFIG_CHR_DEV_SG=y CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_REPORT_LUNS=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_SYM53C8XX_2=y CONFIG_MD=y CONFIG_BLK_DEV_MD=y CONFIG_MD_LINEAR=y CONFIG_MD_RAID0=y CONFIG_MD_RAID1=y CONFIG_MD_RAID5=y CONFIG_NET=y CONFIG_PACKET=y CONFIG_UNIX=y CONFIG_INET=y CONFIG_IP_MULTICAST=y CONFIG_IP_ADVANCED_ROUTER=y CONFIG_IP_ROUTE_VERBOSE=y CONFIG_IP_ROUTE_LARGE_TABLES=y CONFIG_SYN_COOKIES=y CONFIG_IPV6_SCTP__=y CONFIG_NETDEVICES=y CONFIG_DUMMY=y CONFIG_NET_ETHERNET=y CONFIG_NET_TULIP=y CONFIG_TULIP=y CONFIG_TULIP_MWI=y CONFIG_TULIP_MMIO=y CONFIG_NET_PCI=y CONFIG_E100=y CONFIG_8139CP=y CONFIG_8139TOO=y CONFIG_VIA_RHINE=y CONFIG_VIA_RHINE_MMIO=y CONFIG_INPUT=y CONFIG_INPUT_MOUSEDEV=y CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_SOUND_GAMEPORT=y CONFIG_SERIO=y CONFIG_SERIO_I8042=y CONFIG_SERIO_SERPORT=y CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=y CONFIG_INPUT_MISC=y CONFIG_INPUT_PCSPKR=y CONFIG_VT=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y CONFIG_SERIAL_8250=y CONFIG_SERIAL_CORE=y CONFIG_UNIX98_PTYS=y CONFIG_PRINTER=y CONFIG_I2C=m CONFIG_I2C_ALGOBIT=m CONFIG_I2C_CHARDEV=m CONFIG_I2C_AMD756=m CONFIG_I2C_AMD8111=m CONFIG_SENSORS_ADM1021=m CONFIG_SENSORS_LM75=m CONFIG_SENSORS_VIA686A=m CONFIG_SENSORS_W83781D=m CONFIG_I2C_SENSOR=m CONFIG_WATCHDOG=y CONFIG_SOFT_WATCHDOG=y CONFIG_RTC=y CONFIG_AGP=y CONFIG_AGP3=y CONFIG_AGP_VIA=y CONFIG_DRM=y CONFIG_DRM_MGA=y CONFIG_RAW_DRIVER=y CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y CONFIG_JBD=y CONFIG_FS_MBCACHE=y CONFIG_REISERFS_FS=y CONFIG_ISO9660_FS=y CONFIG_JOLIET=y CONFIG_UDF_FS=y CONFIG_FAT_FS=y CONFIG_VFAT_FS=y CONFIG_NTFS_FS=y CONFIG_PROC_FS=y CONFIG_DEVPTS_FS=y CONFIG_TMPFS=y CONFIG_RAMFS=y CONFIG_MSDOS_PARTITION=y CONFIG_NLS=y CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ISO8859_1=y CONFIG_FB=y CONFIG_VIDEO_SELECT=y CONFIG_FB_MATROX=y CONFIG_FB_MATROX_G450=y CONFIG_FB_MATROX_G100=y CONFIG_VGA_CONSOLE=y CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y CONFIG_PCI_CONSOLE=y CONFIG_FONTS=y CONFIG_FONT_SUN12x22=y CONFIG_LOGO=y CONFIG_LOGO_LINUX_MONO=y CONFIG_LOGO_LINUX_VGA16=y CONFIG_LOGO_LINUX_CLUT224=y CONFIG_SOUND=y CONFIG_SND=y CONFIG_SND_SEQUENCER=y CONFIG_SND_OSSEMUL=y CONFIG_SND_MIXER_OSS=y CONFIG_SND_PCM_OSS=y CONFIG_SND_SEQUENCER_OSS=y CONFIG_SND_RTCTIMER=y CONFIG_SND_EMU10K1=y CONFIG_SND_CMIPCI=y CONFIG_SND_INTEL8X0=y CONFIG_SND_VIA82XX=y CONFIG_USB=y CONFIG_USB_DEVICEFS=y CONFIG_USB_PRINTER=y CONFIG_USB_SCANNER=y CONFIG_DEBUG_KERNEL=y CONFIG_MAGIC_SYSRQ=y CONFIG_KALLSYMS=y CONFIG_DEBUG_INFO=y CONFIG_FRAME_POINTER=y CONFIG_X86_EXTRA_IRQS=y CONFIG_X86_FIND_SMP_CONFIG=y CONFIG_X86_MPPARSE=y CONFIG_X86_BIOS_REBOOT=y
--=_courier-29359-1049532085-0001-2--