[PATCH] e100_asf_enabled is only used when CONFIG_PM

[Stephen Rothwell]

Hi,

Not sure where this needs to be sent. This patch kills a warning
when CONFIG_PM is not set.

-- 
Cheers,
Stephen Rothwell                    [e-mail]
http://www.canb.auug.org.au/~sfr/

diff -ruN 2.5.66-040110/drivers/net/e100/e100_main.c 2.5.66-040110-e100/drivers/net/e100/e100_main.c
--- 2.5.66-040110/drivers/net/e100/e100_main.c	2003-04-02 13:35:15.000000000 +1000
+++ 2.5.66-040110-e100/drivers/net/e100/e100_main.c	2003-04-02 13:25:00.000000000 +1000
@@ -228,7 +228,6 @@
 				 char *);
 unsigned char e100_wait_exec_cmplx(struct e100_private *, u32, u8, u8);
 void e100_exec_cmplx(struct e100_private *, u32, u8);
-static unsigned char e100_asf_enabled(struct e100_private *bdp);
 
 /**
  * e100_get_rx_struct - retrieve cell to hold skb buff from the pool
@@ -4102,6 +4101,31 @@
 }
 
 #ifdef CONFIG_PM
+/**
+ * e100_asf_enabled - checks if ASF is configured on the current adaper
+ *                    by reading registers 0xD and 0x90 in the EEPROM 
+ * @bdp: atapter's private data struct
+ *
+ * Returns: true if ASF is enabled
+ */
+static unsigned char
+e100_asf_enabled(struct e100_private *bdp)
+{
+	u16 asf_reg;
+	u16 smbus_addr_reg;
+	if ((bdp->pdev->device >= 0x1050) && (bdp->pdev->device <= 0x1055)) {
+		asf_reg = e100_eeprom_read(bdp, EEPROM_CONFIG_ASF);
+		if ((asf_reg & EEPROM_FLAG_ASF)
+		    && !(asf_reg & EEPROM_FLAG_GCL)) {
+			smbus_addr_reg = 
+				e100_eeprom_read(bdp, EEPROM_SMBUS_ADDR);
+			if ((smbus_addr_reg & 0xFF) != 0xFE) 
+				return true;
+		}
+	}
+	return false;
+}
+
 static int
 e100_notify_reboot(struct notifier_block *nb, unsigned long event, void *p)
 {
@@ -4164,31 +4188,6 @@
 }
 #endif /* CONFIG_PM */
 
-/**
- * e100_asf_enabled - checks if ASF is configured on the current adaper
- *                    by reading registers 0xD and 0x90 in the EEPROM 
- * @bdp: atapter's private data struct
- *
- * Returns: true if ASF is enabled
- */
-static unsigned char
-e100_asf_enabled(struct e100_private *bdp)
-{
-	u16 asf_reg;
-	u16 smbus_addr_reg;
-	if ((bdp->pdev->device >= 0x1050) && (bdp->pdev->device <= 0x1055)) {
-		asf_reg = e100_eeprom_read(bdp, EEPROM_CONFIG_ASF);
-		if ((asf_reg & EEPROM_FLAG_ASF)
-		    && !(asf_reg & EEPROM_FLAG_GCL)) {
-			smbus_addr_reg = 
-				e100_eeprom_read(bdp, EEPROM_SMBUS_ADDR);
-			if ((smbus_addr_reg & 0xFF) != 0xFE) 
-				return true;
-		}
-	}
-	return false;
-}
-
 #ifdef E100_CU_DEBUG
 unsigned char
 e100_cu_unknown_state(struct e100_private *bdp)