Serial port driver.
- Osamu Tomita
diff -Nru linux/drivers/serial/8250_pnp.c linux98/drivers/serial/8250_pnp.c
--- linux/drivers/serial/8250_pnp.c 2002-12-11 13:10:07.000000000 +0900
+++ linux98/drivers/serial/8250_pnp.c 2002-12-11 13:16:51.000000000 +0900
@@ -188,6 +188,8 @@
{ "MVX00A1", 0 },
/* PC Rider K56 Phone System PnP */
{ "MVX00F2", 0 },
+ /* NEC 98NOTE SPEAKER PHONE FAX MODEM(33600bps) */
+ { "nEC8241", 0 },
/* Pace 56 Voice Internal Plug & Play Modem */
{ "PMC2430", 0 },
/* Generic */
@@ -373,6 +375,9 @@
((port->min == 0x2f8) ||
(port->min == 0x3f8) ||
(port->min == 0x2e8) ||
+#ifdef CONFIG_X86_PC9800
+ (port->min == 0x8b0) ||
+#endif
(port->min == 0x3e8)))
return 0;
}
diff -Nru linux/drivers/serial/Kconfig linux98/drivers/serial/Kconfig
--- linux/drivers/serial/Kconfig 2003-01-14 14:59:16.000000000 +0900
+++ linux98/drivers/serial/Kconfig 2003-01-17 13:07:46.000000000 +0900
@@ -372,14 +372,25 @@
bool "Use NEC V850E on-chip UART for console"
depends on V850E_NB85E_UART
+config SERIAL98
+ tristate "PC-9800 8251-based primary serial port support"
+ depends on X86_PC9800
+ help
+ If you want to use standard primary serial ports on PC-9800,
+ say Y. Otherwise, say N.
+
+config SERIAL98_CONSOLE
+ bool "Support for console on PC-9800 standard serial port"
+ depends on SERIAL98=y
+
config SERIAL_CORE
tristate
- default m if SERIAL_AMBA!=y && SERIAL_CLPS711X!=y && SERIAL_21285!=y && !SERIAL_SA1100 && !SERIAL_ANAKIN && !SERIAL_UART00 && SERIAL_8250!=y && SERIAL_MUX!=y && !SERIAL_ROCKETPORT && !SERIAL_SUNCORE && !V850E_NB85E_UART && (SERIAL_AMBA=m || SERIAL_CLPS711X=m || SERIAL_21285=m || SERIAL_8250=m || SERIAL_MUX=m)
- default y if SERIAL_AMBA=y || SERIAL_CLPS711X=y || SERIAL_21285=y || SERIAL_SA1100 || SERIAL_ANAKIN || SERIAL_UART00 || SERIAL_8250=y || SERIAL_MUX=y || SERIAL_ROCKETPORT || SERIAL_SUNCORE || V850E_NB85E_UART
+ default m if SERIAL_AMBA!=y && SERIAL_CLPS711X!=y && SERIAL_21285!=y && !SERIAL_SA1100 && !SERIAL_ANAKIN && !SERIAL_UART00 && SERIAL_8250!=y && SERIAL_MUX!=y && !SERIAL_ROCKETPORT && !SERIAL_SUNCORE && !V850E_NB85E_UART && (SERIAL_AMBA=m || SERIAL_CLPS711X=m || SERIAL_21285=m || SERIAL_8250=m || SERIAL_MUX=m || SERIAL98=m)
+ default y if SERIAL_AMBA=y || SERIAL_CLPS711X=y || SERIAL_21285=y || SERIAL_SA1100 || SERIAL_ANAKIN || SERIAL_UART00 || SERIAL_8250=y || SERIAL_MUX=y || SERIAL_ROCKETPORT || SERIAL_SUNCORE || V850E_NB85E_UART || SERIAL98=y
config SERIAL_CORE_CONSOLE
bool
- depends on SERIAL_AMBA_CONSOLE || SERIAL_CLPS711X_CONSOLE || SERIAL_21285_CONSOLE || SERIAL_SA1100_CONSOLE || SERIAL_ANAKIN_CONSOLE || SERIAL_UART00_CONSOLE || SERIAL_8250_CONSOLE || SERIAL_MUX_CONSOLE || SERIAL_SUNCORE || V850E_NB85E_UART_CONSOLE
+ depends on SERIAL_AMBA_CONSOLE || SERIAL_CLPS711X_CONSOLE || SERIAL_21285_CONSOLE || SERIAL_SA1100_CONSOLE || SERIAL_ANAKIN_CONSOLE || SERIAL_UART00_CONSOLE || SERIAL_8250_CONSOLE || SERIAL_MUX_CONSOLE || SERIAL_SUNCORE || V850E_NB85E_UART_CONSOLE || SERIAL98_CONSOLE
default y
config SERIAL_68328
diff -Nru linux-2.5.60/drivers/serial/Makefile linux98-2.5.60/drivers/serial/Makefile
--- linux-2.5.60/drivers/serial/Makefile 2003-02-11 03:38:32.000000000 +0900
+++ linux98-2.5.60/drivers/serial/Makefile 2003-02-11 13:32:49.000000000 +0900
@@ -27,3 +27,4 @@
obj-$(CONFIG_SERIAL_68360) += 68360serial.o
obj-$(CONFIG_SERIAL_COLDFIRE) += mcfserial.o
obj-$(CONFIG_V850E_NB85E_UART) += nb85e_uart.o
+obj-$(CONFIG_SERIAL98) += serial98.o
diff -Nru linux/drivers/serial/serial98.c linux98/drivers/serial/serial98.c
--- linux/drivers/serial/serial98.c 1970-01-01 09:00:00.000000000 +0900
+++ linux98/drivers/serial/serial98.c 2003-01-17 21:16:43.000000000 +0900
@@ -0,0 +1,1125 @@
+/*
+ * linux/drivers/serial/serial98.c
+ *
+ * Driver for NEC PC-9801/PC-9821 standard serial ports
+ *
+ * Based on drivers/serial/8250.c, by Russell King.
+ * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+ *
+ * Copyright (C) 2002 Osamu Tomita <tomita@cinet.co.jp>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/tty.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/serial.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/serial_reg.h>
+#include <linux/delay.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/pc9800.h>
+#include <asm/pc9800_sca.h>
+
+#if defined(CONFIG_SERIAL98_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/serial_core.h>
+
+#define SERIAL98_NR 1
+#define SERIAL98_ISR_PASS_LIMIT 256
+#define SERIAL98_EXT 0x434
+
+//#define RX_8251F 0x130 /* In: Receive buffer */
+//#define TX_8251F 0x130 /* Out: Transmit buffer */
+//#define LSR_8251F 0x132 /* In: Line Status Register */
+//#define MSR_8251F 0x134 /* In: Modem Status Register */
+#define IIR_8251F 0x136 /* In: Interrupt ID Register */
+#define FCR_8251F 0x138 /* I/O: FIFO Control Register */
+#define VFAST_8251F 0x13a /* I/O: VFAST mode Register */
+
+#define CMD_8251F 0x32 /* Out: 8251 Command Resister */
+#define IER2_8251F 0x34 /* I/O: Interrupt Enable Register */
+#define IER1_8251F 0x35 /* I/O: Interrupt Enable Register */
+#define IER1_CTL 0x37 /* Out: Interrupt Enable Register */
+#define DIS_RXR_INT 0x00 /* disable RxRDY Interrupt */
+#define ENA_RXR_INT 0x01 /* enable RxRDY Interrupt */
+#define DIS_TXE_INT 0x02 /* disable TxEMPTY Interrupt */
+#define ENA_TXE_INT 0x03 /* enable TxEMPTY Interrupt */
+#define DIS_TXR_INT 0x04 /* disable TxRDY Interrupt */
+#define ENA_TXR_INT 0x05 /* enable TxRDY Interrupt */
+
+#define CMD_RESET 0x40 /* Reset Command */
+#define CMD_RTS 0x20 /* Set RTS line */
+#define CMD_CLR_ERR 0x10 /* Clear error flag */
+#define CMD_BREAK 0x08 /* Send Break */
+#define CMD_RXE 0x04 /* Enable receive */
+#define CMD_DTR 0x02 /* Set DTR line */
+#define CMD_TXE 0x01 /* Enable send */
+#define CMD_DUMMY 0x00 /* Dummy Command */
+
+#define VFAST_ENABLE 0x80 /* V.Fast mode Enable */
+
+/* Interrupt masks */
+#define INTR_8251_TXRE 0x04
+#define INTR_8251_TXEE 0x02
+#define INTR_8251_RXRE 0x01
+/* I/O Port */
+//#define PORT_8251_DATA 0
+//#define PORT_8251_CMD 2
+//#define PORT_8251_MOD 2
+//#define PORT_8251_STS 2
+/* status read */
+#define STAT_8251_TXRDY 0x01
+#define STAT_8251_RXRDY 0x02
+#define STAT_8251_TXEMP 0x04
+#define STAT_8251_PER 0x08
+#define STAT_8251_OER 0x10
+#define STAT_8251_FER 0x20
+#define STAT_8251_BRK 0x40
+#define STAT_8251_DSR 0x80
+#if 1
+#define STAT_8251F_TXEMP 0x01
+#define STAT_8251F_TXRDY 0x02
+#define STAT_8251F_RXRDY 0x04
+#define STAT_8251F_DSR 0x08
+#define STAT_8251F_OER 0x10
+#define STAT_8251F_PER 0x20
+#define STAT_8251F_FER 0x40
+#define STAT_8251F_BRK 0x80
+#else
+#define STAT_8251F_TXEMP 0x01
+#define STAT_8251F_TEMT 0x01
+#define STAT_8251F_TXRDY 0x02
+#define STAT_8251F_THRE 0x02
+#define STAT_8251F_RXRDY 0x04
+#define STAT_8251F_DSR 0x04
+#define STAT_8251F_PER 0x08
+#define STAT_8251F_OER 0x10
+#define STAT_8251F_FER 0x20
+#define STAT_8251F_BRK 0x40
+#endif
+
+/*
+ * We wrap our port structure around the generic uart_port.
+ */
+struct serial98_port {
+ struct uart_port port;
+ unsigned int type;
+ unsigned int ext;
+ unsigned int lsr_break_flag;
+ unsigned char cmd;
+ unsigned char mode;
+ unsigned char msr;
+ unsigned char ier;
+ unsigned char rxchk;
+ unsigned char txemp;
+ unsigned char txrdy;
+ unsigned char rxrdy;
+ unsigned char brk;
+ unsigned char fe;
+ unsigned char oe;
+ unsigned char pe;
+ unsigned char dr;
+};
+
+#ifdef CONFIG_SERIAL98_CONSOLE
+static void
+serial98_console_write(struct console *co, const char *s, unsigned int count);
+static kdev_t serial98_console_device(struct console *co);
+static int __init serial98_console_setup(struct console *co, char *options);
+
+static struct console serial98_console = {
+ .name = "ttyS",
+ .write = serial98_console_write,
+ .device = serial98_console_device,
+ .setup = serial98_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+};
+
+#define SERIAL98_CONSOLE &serial98_console
+#else
+#define SERIAL98_CONSOLE NULL
+#endif
+
+static struct uart_driver serial98_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = "serial98",
+ .dev_name = "ttyS%d",
+ .major = TTY_MAJOR,
+ .minor = 64,
+ .nr = SERIAL98_NR,
+ .cons = SERIAL98_CONSOLE,
+};
+
+static int serial98_clk;
+static char type_str[48];
+
+#define PORT98 ((struct serial98_port *)port)
+#define PORT (PORT98->port)
+
+static void serial98_fifo_enable(struct uart_port *port, int enable)
+{
+ unsigned char fcr;
+
+ if (PORT.type == PORT_FIFO_PC98 || PORT.type == PORT_VFAST_PC98) {
+ fcr = inb(FCR_8251F);
+ if (enable)
+ fcr |= UART_FCR_ENABLE_FIFO;
+ else
+ fcr &= ~UART_FCR_ENABLE_FIFO;
+ outb(fcr, FCR_8251F);
+ }
+
+ if (!enable)
+ return;
+
+ outb(0, 0x5f); /* wait */
+ outb(0, 0x5f);
+ outb(0, 0x5f);
+ outb(0, 0x5f);
+}
+
+static void serial98_cmd_out(struct uart_port *port, unsigned char cmd)
+{
+ serial98_fifo_enable(port, 0);
+ outb(cmd, CMD_8251F);
+ serial98_fifo_enable(port, 1);
+}
+
+static void serial98_mode_set(struct uart_port *port)
+{
+ serial98_cmd_out(port, CMD_DUMMY);
+ serial98_cmd_out(port, CMD_DUMMY);
+ serial98_cmd_out(port, CMD_DUMMY);
+ serial98_cmd_out(port, CMD_RESET);
+ serial98_cmd_out(port, PORT98->mode);
+}
+
+static unsigned char serial98_msr_in(struct uart_port *port)
+{
+ unsigned long flags;
+ unsigned int ms, st;
+ unsigned int tmp;
+
+ spin_lock_irqsave(&PORT.lock, flags);
+ if (PORT.type == PORT_FIFO_PC98 || PORT.type == PORT_VFAST_PC98) {
+ PORT98->msr = inb(PORT.iobase + 4);
+ } else {
+ ms = inb(0x33);
+ st = inb(0x32);
+ tmp = 0;
+ if(!(ms & 0x20))
+ tmp |= UART_MSR_DCD;
+ if(!(ms & 0x80)) {
+ tmp |= UART_MSR_RI;
+ PORT98->msr |= UART_MSR_RI;
+ }
+ if(!(ms & 0x40))
+ tmp |= UART_MSR_CTS;
+ if(st & 0x80)
+ tmp |= UART_MSR_DSR;
+ PORT98->msr = ((PORT98->msr ^ tmp) >> 4) | tmp;
+ }
+
+ spin_unlock_irqrestore(&PORT.lock, flags);
+ return PORT98->msr;
+}
+
+static void serial98_stop_tx(struct uart_port *port, unsigned int tty_stop)
+{
+ unsigned int ier = inb(IER1_8251F);
+
+ ier &= ~(INTR_8251_TXRE | INTR_8251_TXEE);
+ outb(ier, IER1_8251F);
+}
+
+static void serial98_start_tx(struct uart_port *port, unsigned int tty_start)
+{
+ unsigned int ier = inb(IER1_8251F);
+
+ ier |= INTR_8251_TXRE | INTR_8251_TXEE;
+ outb(ier, IER1_8251F);
+}
+
+static void serial98_stop_rx(struct uart_port *port)
+{
+ PORT.read_status_mask &= ~PORT98->dr;
+ outb(DIS_RXR_INT, IER1_CTL);
+}
+
+static void serial98_enable_ms(struct uart_port *port)
+{
+ outb(PORT98->ier | 0x80, IER2_8251F);
+}
+
+static void serial98_rx_chars(struct uart_port *port, int *status,
+ struct pt_regs *regs)
+{
+ struct tty_struct *tty = PORT.info->tty;
+ unsigned char ch;
+ int max_count = 256;
+
+ do {
+ if (unlikely(tty->flip.count >= TTY_FLIPBUF_SIZE)) {
+ tty->flip.work.func((void *)tty);
+ if (tty->flip.count >= TTY_FLIPBUF_SIZE)
+ return; // if TTY_DONT_FLIP is set
+ }
+ ch = inb(PORT.iobase);
+ *tty->flip.char_buf_ptr = ch;
+ *tty->flip.flag_buf_ptr = TTY_NORMAL;
+ PORT.icount.rx++;
+
+ if (unlikely(*status & (PORT98->brk | PORT98->pe |
+ PORT98->fe | PORT98->oe))) {
+ /*
+ * For statistics only
+ */
+ if (*status & PORT98->brk) {
+ *status &= ~(PORT98->fe | PORT98->pe);
+ PORT.icount.brk++;
+ /*
+ * We do the SysRQ and SAK checking
+ * here because otherwise the break
+ * may get masked by ignore_status_mask
+ * or read_status_mask.
+ */
+ if (uart_handle_break(&PORT))
+ goto ignore_char;
+ } else if (*status & PORT98->pe)
+ PORT.icount.parity++;
+ else if (*status & PORT98->fe)
+ PORT.icount.frame++;
+ if (*status & PORT98->oe)
+ PORT.icount.overrun++;
+
+ /*
+ * Mask off conditions which should be ingored.
+ */
+ *status &= PORT.read_status_mask;
+
+#ifdef CONFIG_SERIAL98_CONSOLE
+ if (PORT.line == PORT.cons->index) {
+ /* Recover the break flag from console xmit */
+ *status |= PORT98->lsr_break_flag;
+ PORT98->lsr_break_flag = 0;
+ }
+#endif
+ if (*status & PORT98->brk) {
+ *tty->flip.flag_buf_ptr = TTY_BREAK;
+ } else if (*status & PORT98->pe)
+ *tty->flip.flag_buf_ptr = TTY_PARITY;
+ else if (*status & PORT98->fe)
+ *tty->flip.flag_buf_ptr = TTY_FRAME;
+ }
+ if (uart_handle_sysrq_char(&PORT, ch, regs))
+ goto ignore_char;
+ if ((*status & PORT.ignore_status_mask) == 0) {
+ tty->flip.flag_buf_ptr++;
+ tty->flip.char_buf_ptr++;
+ tty->flip.count++;
+ }
+ if ((*status & PORT98->oe) &&
+ tty->flip.count < TTY_FLIPBUF_SIZE) {
+ /*
+ * Overrun is special, since it's reported
+ * immediately, and doesn't affect the current
+ * character.
+ */
+ *tty->flip.flag_buf_ptr = TTY_OVERRUN;
+ tty->flip.flag_buf_ptr++;
+ tty->flip.char_buf_ptr++;
+ tty->flip.count++;
+ }
+ ignore_char:
+ *status = inb(PORT.iobase + 2);
+ } while ((*status & PORT98->rxchk) && (max_count-- > 0));
+ tty_flip_buffer_push(tty);
+}
+
+static void serial98_tx_chars(struct uart_port *port)
+{
+ struct circ_buf *xmit = &PORT.info->xmit;
+ int count;
+
+ if (PORT.x_char) {
+ outb(PORT.x_char, PORT.iobase);
+ PORT.icount.tx++;
+ PORT.x_char = 0;
+ return;
+ }
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&PORT)) {
+ serial98_stop_tx(port, 0);
+ return;
+ }
+
+ count = PORT.fifosize;
+ do {
+ outb(xmit->buf[xmit->tail], PORT.iobase);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ PORT.icount.tx++;
+ if (uart_circ_empty(xmit))
+ break;
+ } while (--count > 0);
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&PORT);
+
+ if (uart_circ_empty(xmit))
+ serial98_stop_tx(&PORT, 0);
+}
+
+static void serial98_modem_status(struct uart_port *port)
+{
+ int status;
+
+ status = serial98_msr_in(port);
+
+ if ((status & UART_MSR_ANY_DELTA) == 0)
+ return;
+
+ if (status & UART_MSR_TERI)
+ PORT.icount.rng++;
+ if (status & UART_MSR_DDSR)
+ PORT.icount.dsr++;
+ if (status & UART_MSR_DDCD)
+ uart_handle_dcd_change(&PORT, status & UART_MSR_DCD);
+ if (status & UART_MSR_DCTS)
+ uart_handle_cts_change(&PORT, status & UART_MSR_CTS);
+
+ wake_up_interruptible(&PORT.info->delta_msr_wait);
+}
+
+static void serial98_int(int irq, void *port, struct pt_regs *regs)
+{
+ unsigned int status;
+
+ spin_lock(&PORT.lock);
+ status = inb(PORT.iobase + 2);
+ if (status & PORT98->rxrdy) {
+ serial98_rx_chars(port, &status, regs);
+ }
+ serial98_modem_status(port);
+ if (status & PORT98->txrdy) {
+ serial98_tx_chars(port);
+ }
+ spin_unlock(&PORT.lock);
+}
+
+static unsigned int serial98_tx_empty(struct uart_port *port)
+{
+ unsigned long flags;
+ unsigned int ret = 0;
+
+ spin_lock_irqsave(&PORT.lock, flags);
+ if (inb(PORT.iobase + 2) & PORT98->txemp)
+ ret = TIOCSER_TEMT;
+
+ spin_unlock_irqrestore(&PORT.lock, flags);
+ return ret;
+}
+
+static unsigned int serial98_get_mctrl(struct uart_port *port)
+{
+ unsigned char status;
+ unsigned int ret = 0;
+
+ status = serial98_msr_in(port);
+ if (status & UART_MSR_DCD)
+ ret |= TIOCM_CAR;
+ if (status & UART_MSR_RI)
+ ret |= TIOCM_RNG;
+ if (status & UART_MSR_DSR)
+ ret |= TIOCM_DSR;
+ if (status & UART_MSR_CTS)
+ ret |= TIOCM_CTS;
+ return ret;
+}
+
+static void serial98_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ PORT98->cmd &= 0xdd;
+ if (mctrl & TIOCM_RTS)
+ PORT98->cmd |= CMD_RTS;
+
+ if (mctrl & TIOCM_DTR)
+ PORT98->cmd |= CMD_DTR;
+
+ serial98_cmd_out(port, PORT98->cmd);
+}
+
+static void serial98_break_ctl(struct uart_port *port, int break_state)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&PORT.lock, flags);
+ if (break_state == -1)
+ PORT98->cmd |= CMD_BREAK;
+ else
+ PORT98->cmd &= ~CMD_BREAK;
+
+ serial98_cmd_out(port, PORT98->cmd);
+ spin_unlock_irqrestore(&PORT.lock, flags);
+}
+
+static int serial98_startup(struct uart_port *port)
+{
+ int retval;
+
+ if (PORT.type == PORT_8251_PC98) {
+ /* Wake up UART */
+ PORT98->mode = 0xfc;
+ serial98_mode_set(port);
+ outb(DIS_RXR_INT, IER1_CTL);
+ outb(DIS_TXE_INT, IER1_CTL);
+ outb(DIS_TXR_INT, IER1_CTL);
+ PORT98->mode = 0;
+ serial98_mode_set(port);
+ }
+
+ /*
+ * Clear the FIFO buffers and disable them.
+ * (they will be reeanbled in set_termios())
+ */
+ if (PORT.type == PORT_FIFO_PC98 || PORT.type == PORT_VFAST_PC98) {
+ outb(UART_FCR_ENABLE_FIFO, FCR_8251F);
+ outb((UART_FCR_ENABLE_FIFO
+ | UART_FCR_CLEAR_RCVR
+ | UART_FCR_CLEAR_XMIT), FCR_8251F);
+ outb(0, FCR_8251F);
+ }
+
+ /* Clear the interrupt registers. */
+ inb(0x30);
+ inb(0x32);
+ if (PORT.type == PORT_FIFO_PC98 || PORT.type == PORT_VFAST_PC98) {
+ inb(PORT.iobase);
+ inb(PORT.iobase + 2);
+ inb(PORT.iobase + 4);
+ inb(PORT.iobase + 6);
+ }
+
+ /* Allocate the IRQ */
+ retval = request_irq(PORT.irq, serial98_int, 0,
+ serial98_reg.driver_name, port);
+ if (retval)
+ return retval;
+
+ /*
+ * Now, initialize the UART
+ */
+ PORT98->mode = 0x4e;
+ serial98_mode_set(port);
+ PORT98->cmd = 0x15;
+ serial98_cmd_out(port, PORT98->cmd);
+ PORT98->cmd = 0x05;
+
+ /*
+ * Finally, enable interrupts
+ */
+ outb(0x00, IER2_8251F);
+ outb(ENA_RXR_INT, IER1_CTL);
+
+ /*
+ * And clear the interrupt registers again for luck.
+ */
+ inb(0x30);
+ inb(0x32);
+ if (PORT.type == PORT_FIFO_PC98 || PORT.type == PORT_VFAST_PC98) {
+ inb(PORT.iobase);
+ inb(PORT.iobase + 2);
+ inb(PORT.iobase + 4);
+ inb(PORT.iobase + 6);
+ }
+
+ return 0;
+}
+
+static void serial98_shutdown(struct uart_port *port)
+{
+ unsigned long flags;
+
+ /*
+ * disable all interrupts
+ */
+ spin_lock_irqsave(&PORT.lock, flags);
+ if (PORT.type == PORT_VFAST_PC98)
+ outb(0, VFAST_8251F); /* V.FAST mode off */
+
+ /* disnable all modem status interrupt */
+ outb(0x80, IER2_8251F);
+
+ /* disnable TX/RX interrupt */
+ outb(0x00, IER2_8251F);
+ outb(DIS_RXR_INT, IER1_CTL);
+ outb(DIS_TXE_INT, IER1_CTL);
+ outb(DIS_TXR_INT, IER1_CTL);
+ PORT98->ier = 0;
+
+ spin_unlock_irqrestore(&PORT.lock, flags);
+
+ /*
+ * Free the interrupt
+ */
+ free_irq(PORT.irq, port);
+
+ /* disable break condition and disable the port */
+ serial98_mode_set(port);
+
+ /* disable FIFO's */
+ if (PORT.type == PORT_FIFO_PC98 || PORT.type == PORT_VFAST_PC98) {
+ outb((UART_FCR_ENABLE_FIFO
+ | UART_FCR_CLEAR_RCVR
+ | UART_FCR_CLEAR_XMIT), FCR_8251F);
+ outb(0, FCR_8251F);
+ }
+
+ inb(PORT.iobase);
+}
+
+static void
+serial98_set_termios(struct uart_port *port, struct termios *termios,
+ struct termios *old)
+{
+ unsigned char stopbit, cval, fcr = 0, ier = 0;
+ unsigned long flags;
+ unsigned int quot;
+
+ stopbit = 0x80;
+ switch (termios->c_cflag & CSIZE) {
+ case CS5:
+ cval = 0x42;
+ stopbit = 0xc0;
+ break;
+ case CS6:
+ cval = 0x46;
+ break;
+ case CS7:
+ cval = 0x4a;
+ break;
+ default:
+ case CS8:
+ cval = 0x4e;
+ break;
+ }
+
+ if (termios->c_cflag & CSTOPB)
+ cval ^= stopbit;
+ if (termios->c_cflag & PARENB)
+ cval |= 0x10;
+ if (!(termios->c_cflag & PARODD))
+ cval |= 0x20;
+
+ /*
+ * Ask the core to calculate the divisor for us.
+ */
+ quot = uart_get_divisor(port, termios, old);
+
+ if (PORT.type == PORT_FIFO_PC98 || PORT.type == PORT_VFAST_PC98) {
+ if ((PORT.uartclk / quot) < (2400 * 16))
+ fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1;
+ else
+ fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_8;
+ }
+
+ /*
+ * Ok, we're now changing the port state. Do it with
+ * interrupts disabled.
+ */
+ spin_lock_irqsave(&PORT.lock, flags);
+
+ /*
+ * Update the per-port timeout.
+ */
+ uart_update_timeout(port, termios->c_cflag, quot);
+
+ PORT.read_status_mask = PORT98->oe | PORT98->txemp | PORT98->dr;
+ if (termios->c_iflag & INPCK)
+ PORT.read_status_mask |= PORT98->fe | PORT98->pe;
+
+ if (termios->c_iflag & (BRKINT | PARMRK))
+ PORT.read_status_mask |= PORT98->brk;
+ /*
+ * Characteres to ignore
+ */
+ PORT.ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ PORT.ignore_status_mask |= PORT98->fe | PORT98->pe;
+
+ if (termios->c_iflag & IGNBRK) {
+ PORT.ignore_status_mask |= PORT98->brk;
+ /*
+ * If we're ignoring parity and break indicators,
+ * ignore overruns too (for real raw support).
+ */
+ if (termios->c_iflag & IGNPAR)
+ PORT.ignore_status_mask |= PORT98->oe;
+ }
+
+ /*
+ * ignore all characters if CREAD is not set
+ */
+ if ((termios->c_cflag & CREAD) == 0)
+ PORT.ignore_status_mask |= PORT98->dr;
+
+ /*
+ * CTS flow control flag and modem status interrupts
+ */
+ if (PORT.flags & UPF_HARDPPS_CD)
+ ier |= 0x80; /* enable modem status interrupt */
+ if (termios->c_cflag & CRTSCTS) {
+ ier |= 0x08; /* enable CTS interrupt */
+ ier |= 0x80; /* enable modem status interrupt */
+ }
+ if (!(termios->c_cflag & CLOCAL)) {
+ ier |= 0x20; /* enable CD interrupt */
+ ier |= 0x80; /* enable modem status interrupt */
+ }
+ PORT98->ier = ier;
+
+ PORT98->mode = cval;
+ serial98_mode_set(port);
+ if (PORT.type == PORT_VFAST_PC98 && quot <= 48) {
+ quot /= 4;
+ if (quot < 1)
+ quot = 1;
+ outb(quot | VFAST_ENABLE, VFAST_8251F);
+ } else {
+ quot /= 3;
+ if (quot < 1)
+ quot = 1;
+ if (PORT.type == PORT_VFAST_PC98)
+ outb(0, VFAST_8251F); /* V.FAST mode off */
+ outb(0xb6, 0x77);
+ outb(quot & 0xff, 0x75); /* LS of divisor */
+ outb(quot >> 8, 0x75); /* MS of divisor */
+ }
+
+ if (fcr & UART_FCR_ENABLE_FIFO) {
+ outb(UART_FCR_ENABLE_FIFO, FCR_8251F);
+ outb(fcr, FCR_8251F);
+ }
+
+ /* enable RX/TX */
+ PORT98->cmd = 0x15;
+ serial98_cmd_out(port, PORT98->cmd);
+ PORT98->cmd = 0x05;
+ /* enable interrupts */
+ outb(0x00, IER2_8251F);
+ outb(ENA_RXR_INT, IER1_CTL);
+ spin_unlock_irqrestore(&PORT.lock, flags);
+}
+
+static const char *serial98_type(struct uart_port *port)
+{
+ char *p;
+
+ switch (PORT.type) {
+ case PORT_8251_PC98:
+ p = "PC98 onboard legacy 8251";
+ break;
+ case PORT_19K_PC98:
+ p = "PC98 onboard max 19200bps";
+ break;
+ case PORT_FIFO_PC98:
+ p = "PC98 onboard with FIFO";
+ break;
+ case PORT_VFAST_PC98:
+ p = "PC98 onboard V.FAST";
+ break;
+ case PORT_PC9861:
+ p = "PC-9861K RS-232C ext. board";
+ break;
+ case PORT_PC9801_101:
+ p = "PC-9801-101 RS-232C ext. board";
+ break;
+ default:
+ return NULL;
+ }
+
+ sprintf(type_str, "%s Clock %dMHz", p, serial98_clk);
+ return type_str;
+}
+
+/* Release the region(s) being used by 'port' */
+static void serial98_release_port(struct uart_port *port)
+{
+ switch (PORT.type) {
+ case PORT_VFAST_PC98:
+ release_region(PORT.iobase + 0xa, 1);
+ case PORT_FIFO_PC98:
+ release_region(PORT.iobase + 8, 1);
+ release_region(PORT.iobase + 6, 1);
+ release_region(PORT.iobase + 4, 1);
+ release_region(PORT.iobase + 2, 1);
+ release_region(PORT.iobase, 1);
+ case PORT_19K_PC98:
+ release_region(SERIAL98_EXT, 1);
+ release_region(0x34, 1);
+ case PORT_8251_PC98:
+ release_region(0x32, 1);
+ release_region(0x30, 1);
+ }
+}
+
+/* Request the region(s) being used by 'port' */
+#define REQ_REGION98(base) (request_region((base), 1, serial98_reg.driver_name))
+static int serial98_request_region(unsigned int type)
+{
+ if (!REQ_REGION98(0x30))
+ return -EBUSY;
+ if (REQ_REGION98(0x32)) {
+ if (type == PORT_8251_PC98)
+ return 0;
+ if (REQ_REGION98(0x34)) {
+ if (REQ_REGION98(SERIAL98_EXT)) {
+ unsigned long base;
+
+ if (type == PORT_19K_PC98)
+ return 0;
+ for (base = 0x130; base <= 0x138; base += 2) {
+ if (!REQ_REGION98(base)) {
+ base -= 2;
+ goto err;
+ }
+ }
+ if (type == PORT_FIFO_PC98)
+ return 0;
+ if (type == PORT_VFAST_PC98) {
+ if (REQ_REGION98(0x13a))
+ return 0;
+ }
+ err:
+ while (base >= 0x130) {
+ release_region(base, 1);
+ base -= 2;
+ }
+ release_region(SERIAL98_EXT, 1);
+ }
+ release_region(0x34, 1);
+ }
+ release_region(0x32, 1);
+ }
+ release_region(0x30, 1);
+ return -EBUSY;
+}
+
+static int serial98_request_port(struct uart_port *port)
+{
+ return serial98_request_region(PORT.type);
+}
+
+/*
+ * Configure/autoconfigure the port.
+ */
+static void serial98_config_port(struct uart_port *port, int flags)
+{
+ if (flags & UART_CONFIG_TYPE)
+ PORT.type = PORT98->type;
+}
+
+/*
+ * verify the new serial_struct (for TIOCSSERIAL).
+ */
+static int serial98_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ switch (ser->type) {
+ case PORT_VFAST_PC98:
+ case PORT_FIFO_PC98:
+ case PORT_19K_PC98:
+ case PORT_8251_PC98:
+ /* not implemented yet
+ case PORT_PC9861:
+ case PORT_PC9801_101:
+ */
+ case PORT_UNKNOWN:
+ break;
+ default:
+ return -EINVAL;
+ }
+ if (ser->irq < 0 || ser->irq >= NR_IRQS)
+ return -EINVAL;
+ if (ser->baud_base < 9600)
+ return -EINVAL;
+ return 0;
+}
+
+static struct uart_ops serial98_ops = {
+ .tx_empty = serial98_tx_empty,
+ .set_mctrl = serial98_set_mctrl,
+ .get_mctrl = serial98_get_mctrl,
+ .stop_tx = serial98_stop_tx,
+ .start_tx = serial98_start_tx,
+ .stop_rx = serial98_stop_rx,
+ .enable_ms = serial98_enable_ms,
+ .break_ctl = serial98_break_ctl,
+ .startup = serial98_startup,
+ .shutdown = serial98_shutdown,
+ .set_termios = serial98_set_termios,
+ .type = serial98_type,
+ .release_port = serial98_release_port,
+ .request_port = serial98_request_port,
+ .config_port = serial98_config_port,
+ .verify_port = serial98_verify_port,
+};
+
+static struct serial98_port serial98_ports[SERIAL98_NR] = {
+ {
+ .port = {
+ .iobase = 0x30,
+ .iotype = SERIAL_IO_PORT,
+ .irq = 4,
+ .fifosize = 1,
+ .ops = &serial98_ops,
+ .flags = ASYNC_BOOT_AUTOCONF,
+ .line = 0,
+ },
+ .rxchk = STAT_8251_RXRDY,
+ .txemp = STAT_8251_TXEMP,
+ .txrdy = STAT_8251_TXRDY,
+ .rxrdy = STAT_8251_RXRDY,
+ .brk = STAT_8251_BRK,
+ .fe = STAT_8251_FER,
+ .oe = STAT_8251_OER,
+ .pe = STAT_8251_PER,
+ .dr = STAT_8251_DSR,
+ },
+};
+
+#ifdef CONFIG_SERIAL98_CONSOLE
+
+#define BOTH_EMPTY (PORT98->txemp | PORT98->txrdy)
+
+/*
+ * Wait for transmitter & holding register to empty
+ */
+static inline void wait_for_xmitr(struct uart_port *port)
+{
+ unsigned int status, tmout = 10000;
+
+ /* Wait up to 10ms for the character(s) to be sent. */
+ do {
+ status = inb(PORT.iobase + 2);
+
+ if (status & PORT98->brk)
+ PORT98->lsr_break_flag = PORT98->brk;
+
+ if (--tmout == 0)
+ break;
+ udelay(1);
+ } while ((status & BOTH_EMPTY) != BOTH_EMPTY);
+
+ /* Wait up to 1s for flow control if necessary */
+ if (PORT.flags & UPF_CONS_FLOW) {
+ tmout = 1000000;
+ while (--tmout &&
+ ((serial98_msr_in(port) & UART_MSR_CTS) == 0))
+ udelay(1);
+ }
+}
+
+/*
+ * Print a string to the serial port trying not to disturb
+ * any possible real use of the port...
+ *
+ * The console_lock must be held when we get here.
+ */
+static void
+serial98_console_write(struct console *co, const char *s, unsigned int count)
+{
+ struct uart_port *port = (struct uart_port *)&serial98_ports[co->index];
+ unsigned int ier1, ier2;
+ int i;
+
+ /*
+ * First save the UER then disable the interrupts
+ */
+ ier1 = inb(IER1_8251F);
+ ier2 = inb(IER2_8251F);
+ /* disnable all modem status interrupt */
+ outb(0x80, IER2_8251F);
+
+ /* disnable TX/RX interrupt */
+ outb(0x00, IER2_8251F);
+ outb(DIS_RXR_INT, IER1_CTL);
+ outb(DIS_TXE_INT, IER1_CTL);
+ outb(DIS_TXR_INT, IER1_CTL);
+
+ /*
+ * Now, do each character
+ */
+ for (i = 0; i < count; i++, s++) {
+ wait_for_xmitr(port);
+
+ /*
+ * Send the character out.
+ * If a LF, also do CR...
+ */
+ outb(*s, PORT.iobase);
+ if (*s == 10) {
+ wait_for_xmitr(port);
+ outb(13, PORT.iobase);
+ }
+ }
+
+ /*
+ * Finally, wait for transmitter to become empty
+ * and restore the IER
+ */
+ wait_for_xmitr(port);
+
+ /* restore TX/RX interrupt */
+ outb(0x00, IER2_8251F);
+ if (ier1 & 0x01)
+ outb(ENA_RXR_INT, IER1_CTL);
+ if (ier1 & 0x02)
+ outb(ENA_TXE_INT, IER1_CTL);
+ if (ier1 & 0x04)
+ outb(ENA_TXR_INT, IER1_CTL);
+
+ /* restore modem status interrupt */
+ outb(ier2, IER2_8251F);
+}
+
+static kdev_t serial98_console_device(struct console *co)
+{
+ return mk_kdev(TTY_MAJOR, 64 + co->index);
+}
+
+static int __init serial98_console_setup(struct console *co, char *options)
+{
+ struct uart_port *port;
+ int baud = 9600;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ /*
+ * Check whether an invalid uart number has been specified, and
+ * if so, search for the first available port that does have
+ * console support.
+ */
+ if (co->index >= SERIAL98_NR)
+ co->index = 0;
+ port = &serial98_ports[co->index].port;
+
+ /*
+ * Temporary fix.
+ */
+ spin_lock_init(&port->lock);
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+void __init serial98_console_init(void)
+{
+ register_console(&serial98_console);
+}
+
+#endif /* CONFIG_SERIAL98_CONSOLE */
+
+
+static int __init serial98_init(void)
+{
+ int ret;
+ unsigned char iir1, iir2;
+
+ if (PC9800_8MHz_P()) {
+ serial98_clk = 8;
+ serial98_ports[0].port.uartclk = 374400 * 16;
+ } else {
+ serial98_clk = 5;
+ serial98_ports[0].port.uartclk = 460800 * 16;
+ }
+
+ printk(KERN_INFO "serial98: PC-9801 standard serial port driver Version 0.1alpha\n");
+ serial98_ports[0].type = PORT_8251_PC98;
+ /* Check FIFO exist */
+ iir1 = inb(IIR_8251F);
+ iir2 = inb(IIR_8251F);
+ if ((iir1 & 0x40) != (iir2 & 0x40) && (iir1 & 0x20) == (iir2 & 0x20)) {
+ serial98_ports[0].port.iobase = 0x130;
+ serial98_ports[0].port.fifosize = 16;
+ serial98_ports[0].rxchk = STAT_8251F_DSR;
+ serial98_ports[0].txemp = STAT_8251F_TXEMP;
+ serial98_ports[0].txrdy = STAT_8251F_TXRDY;
+ serial98_ports[0].rxrdy = STAT_8251F_RXRDY;
+ serial98_ports[0].brk = STAT_8251F_BRK;
+ serial98_ports[0].fe = STAT_8251F_FER;
+ serial98_ports[0].oe = STAT_8251F_OER;
+ serial98_ports[0].pe = STAT_8251F_PER;
+ serial98_ports[0].dr = STAT_8251F_DSR;
+
+ if (*(unsigned char*)__va(PC9821SCA_RSFLAGS) & 0x10)
+ serial98_ports[0].type = PORT_VFAST_PC98;
+ else {
+ outb(serial98_ports[0].ext | 0x40, SERIAL98_EXT);
+ serial98_ports[0].port.uartclk *= 4;
+ serial98_ports[0].type = PORT_FIFO_PC98;
+ }
+ } else if ((serial98_ports[0].ext = inb(SERIAL98_EXT)) != 0xff) {
+ outb(serial98_ports[0].ext | 0x40, SERIAL98_EXT);
+ if (inb(SERIAL98_EXT) == (serial98_ports[0].ext | 0x40)) {
+ serial98_ports[0].port.uartclk *= 4;
+ serial98_ports[0].type = PORT_19K_PC98;
+ } else {
+ serial98_ops.enable_ms = NULL;
+ outb(serial98_ports[0].ext, SERIAL98_EXT);
+ }
+ }
+
+ if (serial98_request_region(serial98_ports[0].type))
+ return -EBUSY;
+
+ ret = uart_register_driver(&serial98_reg);
+ if (ret == 0) {
+ int i;
+
+ for (i = 0; i < SERIAL98_NR; i++) {
+ uart_add_one_port(&serial98_reg,
+ (struct uart_port *)&serial98_ports[i]);
+ }
+ }
+
+ return ret;
+}
+
+static void __exit serial98_exit(void)
+{
+ int i;
+
+ if (serial98_ports[0].type == PORT_19K_PC98
+ || serial98_ports[0].type == PORT_FIFO_PC98)
+ outb(serial98_ports[0].ext, SERIAL98_EXT);
+
+ for (i = 0; i < SERIAL98_NR; i++) {
+ uart_remove_one_port(&serial98_reg,
+ (struct uart_port *)&serial98_ports[i]);
+ }
+
+ uart_unregister_driver(&serial98_reg);
+}
+
+module_init(serial98_init);
+module_exit(serial98_exit);
+
+EXPORT_NO_SYMBOLS;
+
+MODULE_AUTHOR("Osamu Tomita <tomita@cinet.co.jp>");
+MODULE_DESCRIPTION("PC-9801 standard serial port driver Version 0.1alpha");
+MODULE_LICENSE("GPL");
diff -Nru linux/include/linux/serial_core.h linux98/include/linux/serial_core.h
--- linux/include/linux/serial_core.h 2003-01-09 13:03:55.000000000 +0900
+++ linux98/include/linux/serial_core.h 2003-01-10 10:53:38.000000000 +0900
@@ -58,6 +58,14 @@
/* NEC v850. */
#define PORT_NB85E_UART 40
+/* NEC PC-9800 */
+#define PORT_8251_PC98 41
+#define PORT_19K_PC98 42
+#define PORT_FIFO_PC98 43
+#define PORT_VFAST_PC98 44
+#define PORT_PC9861 45
+#define PORT_PC9801_101 46
+
#ifdef __KERNEL__
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/