RE: Dual athlon XP 1800 problems

[steve roemen]

i had similar issues on my old 2460 board.

i found out that a huge power supply doesn't cut it, you need a QUALITY
power supply of ~400watts( more specifically the 5 volt bus).

i also found out the hard way that i believe tyan didn't design that board
properly because the 5 volt part of the connectors were burned up on the PS
and MB.

i've since replaced with a s2466n-4m  and am very happy.

i'd check your power supply connector before it burns up yours too...

-steve

-----Original Message-----
From: [e-mail]
[mailto:[e-mail]]On Behalf Of Ken Witherow
Sent: Friday, November 15, 2002 11:26 AM
To: David Crooke
Cc: [e-mail]
Subject: Re: Dual athlon XP 1800 problems

> 1. When I first put it together, it would consistenly run OK for a
> period of 4-5 minutes, quite precisely - no less than 4, no more than 5
> and then just lock up HARD - no Ctrl-Alt-Del, no kernel panics, nothing.
> Once or twice it seemed like it stuttered - as if the load was like
> 10.00 or higher, the keystroke echo would take 2-3 seconds.
>
> 2. First try - I pulled the Tekram (it's ancient and has bootable BIOS)
> - no difference
>
> 3. Tried some BIOS settings (e.g. SMP 1.1 mode) - it DOES NOT like this;
> any BIOS changes AT ALL (even seemingly harmless ones like Num Lock)
> appear to mess it up totally, and LILO hangs at "LI" when trying to
> start. Restored factory defaults.

I have a S2460 with dual 1800MPs using BIOS rev 1.04. I had very similar
problems (random hangs, sometimes after 2 minutes, sometimes after 36
hours). Here's what I did to solve them:

1) Turn off power management in the BIOS. I still have power management
enabled in linux and all is fine.

2) (this is the most important one) Make sure you have a minimum of a 500
watt power supply. Each CPU alone is rated for 66 watts of consumption.

3) I still get random hangs at boot (usually after rebooting linux) and I
believe this is due to some ACPI problem. A hard reboot (turn the power
supply off and on) fixes it for me.

4) There are a couple bugs with the 760MP chipset and APICs. To see if
they're affecting you, add "mem=nopentium noapic" to your kernel
parameters (I can run fine without them).

> 4. Then I noticed that the CPU1 heatsink was quite warm (maybe 70C
> feeling around the thick bit of the aluminium) whereas CPU0 heatsink is
> just above room temp.
>
> 5. Checking the Winbond monitoring in the BIOS** menu, it comes up
> showing both CPU's at 77C, then as you hit keys it takes proper
> readings, and claims both CPUs within 1-2 degrees of each other (??). It
> seems accurate on fan speeds though. Both fans running pretty fast,
> 5500-6200 RPM.

My BIOS reports the right temps but lm_sensors didn't. I too was getting
temps in the 75C+ range. To fix lm_sensors, do the following:

echo "2" > /proc/sys/dev/sensors/w83782d-i2c-0-2d/sensor1
echo "2" > /proc/sys/dev/sensors/w83782d-i2c-0-2d/sensor2
echo "2" > /proc/sys/dev/sensors/w83782d-i2c-0-2d/sensor3

> 7. Brought it up to single user mode console, to see if it was video
> card etc. - did some testing of just letting it mostly idle (while true
> - uptime - sleep 1 - etc.) and locked up 1-2 more times.

I thought it was my video card too... so I went out and spent $90 on a new
one only to find it does the same thing.

> 8. Rebooted again, now it's up and running and appears stable (still 1
> CPU), so I took it up to full init 5 and it stayed up (and so I'm
> writing this email :-)  Once or twice seemed to stall again for 1-2
> seconds (interrupt storm ???) but recovered.

I notice this sometimes too... I chalk it up to some SMP locking
somewhere. Currently up 6 days, 3:53 with the maximum around 40 days
(rebooted to upgrade kernel).

> Other observation, possibly unrelated: the unpacking of the kernel seems
> very slow for an otherwise pretty quick machine - the dots when it says
> "Loading xxx..." tick at about 1 per second, much like a laptop with
> PC-66 memory, compared with 4-5 per second for the Pentium III
> 800/PC-133 motherboard I just hauled out.

When mine hasn't reset right (the aforementioned ACPI lockup), mine does
this. It was especially prevalent before I upgraded my power supply from
400 to 550 watts

> ** The temperature sensor driver stuff didn't seem to come with the
> kernel ??

pick up the lm_sensors package

--
       Ken Witherow <phantoml AT rochester.rr.com>
           ICQ: 21840670  AIM: phantomlordken
               http://www.krwtech.com/ken