Yes, you are right. It is the APIC problem...
polaris:/proc# cat interrupts
CPU0 CPU1
0: 155563 0 XT-PIC timer
1: 2510 0 XT-PIC keyboard
2: 0 0 XT-PIC cascade
5: 3421 0 XT-PIC eth0
8: 23 0 XT-PIC rtc
9: 26243 0 XT-PIC sym53c8xx, eth1
10: 301052 0 XT-PIC ide2, ide3
NMI: 0 0
LOC: 155501 155500
ERR: 1427
MIS: 0
I'm not sure if the following will make the problem abvious
for people that know anything about the APIC, but here it goes.
The following are the relevant boot message for APIC. It was fine with
all of the cards in there except for that Promise controller.
Maybe the interrupt should have triggered on edge not on level?
PS. This is for 2.4.18 kernel
dmesg snip:
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: COMPAQ Product ID: PROLIANT APIC at: 0xFEE00000
Processor #1 Pentium(tm) Pro APIC version 16
Processor #0 Pentium(tm) Pro APIC version 16
I/O APIC #2 Version 17 at 0xFEC00000.
[...]
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 003 03 0 0 0 0 0 1 1 31
01 003 03 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 003 03 1 1 0 1 0 1 1 51
06 003 03 0 0 0 0 0 1 1 59
07 003 03 0 0 0 0 0 1 1 61
08 003 03 0 0 0 0 0 1 1 69
09 003 03 1 1 0 1 0 1 1 71
0a 003 03 1 1 0 1 0 1 1 79
0b 003 03 0 0 0 0 0 1 1 81
0c 003 03 0 0 0 0 0 1 1 89
0d 003 03 0 0 0 0 0 1 1 91
0e 003 03 0 0 0 0 0 1 1 99
0f 003 03 0 0 0 0 0 1 1 A1
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 179.6287 MHz.
..... host bus clock speed is 59.8760 MHz.
cpu: 0, clocks: 598760, slice: 199586
CPU0<T0:598752,T1:399152,D:14,S:199586,C:598760>
cpu: 1, clocks: 598760, slice: 199586
CPU1<T0:598752,T1:199568,D:12,S:199586,C:598760>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/