[RFC][Patchset 4/20] Support for PC-9800

Osamu Tomita (tomita@cinet.co.jp)
Sun, 3 Nov 2002 02:51:00 +0900

Messages sorted by: [ date ][ thread ][ subject ][ author ]
Next message: Osamu Tomita: "[RFC][Patchset 5/20] Support for PC-9800 (core2)"
Previous message: Osamu Tomita: "[RFC][Patchset 3/20] Support for PC-9800 (console)"

This is a part 4/20 of patchset for add support NEC PC-9800 architecture,
against 2.5.45.

Summary:
i386 core modules
- IO port address change
- IRQ number change
- adapted to hardware memory mapping.
- CLOCK_TICK_RATE constat to variable.
some PC-9800 can change base clock by hardware switch!

patch:
diff -urN linux/arch/i386/Makefile linux98/arch/i386/Makefile
--- linux/arch/i386/Makefile Thu Oct 31 13:23:02 2002
+++ linux98/arch/i386/Makefile Thu Oct 31 13:56:57 2002
@@ -48,8 +48,14 @@
ifdef CONFIG_VISWS
MACHINE := mach-visws
else
+ifdef CONFIG_PC9800
+MACHINE := mach-pc9800
+else
+ifndef MACHINE
MACHINE := mach-generic
endif
+endif
+endif
HEAD := arch/i386/kernel/head.o arch/i386/kernel/init_task.o
@@ -65,15 +71,20 @@
CFLAGS += -Iarch/i386/$(MACHINE)
AFLAGS += -Iarch/i386/$(MACHINE)
-makeboot = $(call descend,arch/i386/boot,$(1))
+ifndef CONFIG_PC9800
+ARCHDIR=arch/i386/boot
+else
+ARCHDIR=arch/i386/boot98
+endif
+makeboot = $(call descend,$(ARCHDIR),$(1))
.PHONY: zImage bzImage compressed zlilo bzlilo zdisk bzdisk install \
clean archclean archmrproper
all: bzImage
-BOOTIMAGE=arch/i386/boot/bzImage
-zImage zlilo zdisk: BOOTIMAGE=arch/i386/boot/zImage
+BOOTIMAGE=$(ARCHDIR)/bzImage
+zImage zlilo zdisk: BOOTIMAGE=$(ARCHDIR)/zImage
zImage bzImage: vmlinux
+@$(call makeboot,$(BOOTIMAGE))
@@ -91,5 +102,6 @@
archclean:
@$(MAKE) -f scripts/Makefile.clean obj=arch/i386/boot
+ @$(MAKE) -f scripts/Makefile.clean obj=arch/i386/boot98
archmrproper:
diff -urN linux/arch/i386/Kconfig linux98/arch/i386/Kconfig
--- linux/arch/i386/Kconfig Thu Oct 31 13:23:02 2002
+++ linux98/arch/i386/Kconfig Sat Nov 2 15:11:17 2002
@@ -964,6 +964,12 @@
# Visual Workstation support is utterly broken.
# If you want to see it working mail an VW540 to hch@infradead.org 8)
#bool 'SGI Visual Workstation support' CONFIG_VISWS
+config PC9800
+ bool "NEC PC-9800 architecture support"
+ help
+ To make kernel for NEC PC-9801/PC-9821 architecture, say Y.
+ If say Y, kernel works -ONLY- on PC-9800 architecture.
+
config X86_VISWS_APIC
bool
depends on VISWS
@@ -1056,7 +1062,7 @@
config EISA
bool "EISA support"
- depends on ISA
+ depends on ISA && !PC9800
---help---
The Extended Industry Standard Architecture (EISA) bus was
developed as an open alternative to the IBM MicroChannel bus.
@@ -1072,7 +1078,7 @@
config MCA
bool "MCA support"
- depends on !VISWS
+ depends on !(VISWS || PC9800)
help
MicroChannel Architecture is found in some IBM PS/2 machines and
laptops. It is a bus system similar to PCI or ISA. See
@@ -1420,6 +1426,7 @@
config VGA_CONSOLE
bool "VGA text console"
+ depends on !PC9800
help
Saying Y here will allow you to use Linux in text mode through a
display that complies with the generic VGA standard. Virtually
@@ -1433,6 +1440,7 @@
config VIDEO_SELECT
bool "Video mode selection support"
+ depends on !PC9800
---help---
This enables support for text mode selection on kernel startup. If
you want to take advantage of some high-resolution text mode your
@@ -1446,6 +1454,18 @@
Read the file <file:Documentation/svga.txt> for more information
about the Video mode selection support. If unsure, say N.
+config GDC_CONSOLE
+ bool "PC-9800 GDC text console"
+ depends on PC9800
+ default y
+ help
+ This enables support for PC-9800 standard text mode console.
+ If use PC-9801/PC-9821, Say Y.
+
+config GDC_32BITACCESS
+ bool "Enable 32-bit access to text video RAM"
+ depends on GDC_CONSOLE
+
if EXPERIMENTAL
config MDA_CONSOLE
@@ -1612,6 +1632,12 @@
symbolic stack backtraces. This increases the size of the kernel
somewhat, as all symbols have to be loaded into the kernel image.
+config PC9800_UCGLOG
+ bool "Save kernel messages into UCG-RAM"
+ depends on PC9800
+ help
+ This enables saving kernel messases into PC-9800's NVRAM.
+
config X86_EXTRA_IRQS
bool
depends on X86_LOCAL_APIC
diff -urN linux/arch/i386/kernel/Makefile linux98/arch/i386/kernel/Makefile
--- linux/arch/i386/kernel/Makefile Wed Oct 16 13:20:28 2002
+++ linux98/arch/i386/kernel/Makefile Wed Oct 16 14:27:17 2002
@@ -10,6 +10,10 @@
ptrace.o i8259.o ioport.o ldt.o setup.o time.o sys_i386.o \
pci-dma.o i386_ksyms.o i387.o bluesmoke.o dmi_scan.o \
bootflag.o
+ifeq ($(CONFIG_PC9800),y)
+export-objs += pc9800_debug.o
+obj-$(CONFIG_PC9800) += pc9800_debug.o
+endif
obj-y += cpu/
obj-y += timers/
diff -urN linux/arch/i386/kernel/cpu/proc.c linux98/arch/i386/kernel/cpu/proc.c
--- linux/arch/i386/kernel/cpu/proc.c Mon Jun 17 11:31:35 2002
+++ linux98/arch/i386/kernel/cpu/proc.c Mon Jun 17 23:49:02 2002
@@ -76,7 +76,7 @@
seq_printf(m, "cache size\t: %d KB\n", c->x86_cache_size);

/* We use exception 16 if we have hardware math and we've either seen it or the CPU claims it is internal */
- fpu_exception = c->hard_math && (ignore_irq13 || cpu_has_fpu);
+ fpu_exception = c->hard_math && (ignore_fpu_irq || cpu_has_fpu);
seq_printf(m, "fdiv_bug\t: %s\n"
"hlt_bug\t\t: %s\n"
"f00f_bug\t: %s\n"
diff -urN linux/arch/i386/kernel/i8259.c linux98/arch/i386/kernel/i8259.c
--- linux/arch/i386/kernel/i8259.c Tue Oct 8 03:25:15 2002
+++ linux98/arch/i386/kernel/i8259.c Thu Oct 10 21:46:44 2002
@@ -25,6 +25,8 @@
#include <linux/irq.h>
+#include "io_ports.h"
+
/*
* This is the 'legacy' 8259A Programmable Interrupt Controller,
* present in the majority of PC/AT boxes.
@@ -74,8 +76,8 @@
static unsigned int cached_irq_mask = 0xffff;
#define __byte(x,y) (((unsigned char *)&(y))[x])
-#define cached_21 (__byte(0,cached_irq_mask))
-#define cached_A1 (__byte(1,cached_irq_mask))
+#define cached_master_mask (__byte(0,cached_irq_mask))
+#define cached_slave_mask (__byte(1,cached_irq_mask))
/*
* Not all IRQs can be routed through the IO-APIC, eg. on certain (older)
@@ -96,9 +98,9 @@
spin_lock_irqsave(&i8259A_lock, flags);
cached_irq_mask |= mask;
if (irq & 8)
- outb(cached_A1,0xA1);
+ outb(cached_slave_mask, PIC_SLAVE_IMR);
else
- outb(cached_21,0x21);
+ outb(cached_master_mask, PIC_MASTER_IMR);
spin_unlock_irqrestore(&i8259A_lock, flags);
}
@@ -110,9 +112,9 @@
spin_lock_irqsave(&i8259A_lock, flags);
cached_irq_mask &= mask;
if (irq & 8)
- outb(cached_A1,0xA1);
+ outb(cached_slave_mask, PIC_SLAVE_IMR);
else
- outb(cached_21,0x21);
+ outb(cached_master_mask, PIC_MASTER_IMR);
spin_unlock_irqrestore(&i8259A_lock, flags);
}
@@ -124,9 +126,9 @@
spin_lock_irqsave(&i8259A_lock, flags);
if (irq < 8)
- ret = inb(0x20) & mask;
+ ret = inb(PIC_MASTER_CMD) & mask;
else
- ret = inb(0xA0) & (mask >> 8);
+ ret = inb(PIC_SLAVE_CMD) & (mask >> 8);
spin_unlock_irqrestore(&i8259A_lock, flags);
return ret;
@@ -152,14 +154,14 @@
int irqmask = 1<<irq;
if (irq < 8) {
- outb(0x0B,0x20); /* ISR register */
- value = inb(0x20) & irqmask;
- outb(0x0A,0x20); /* back to the IRR register */
+ outb(0x0B,PIC_MASTER_CMD); /* ISR register */
+ value = inb(PIC_MASTER_CMD) & irqmask;
+ outb(0x0A,PIC_MASTER_CMD); /* back to the IRR register */
return value;
}
- outb(0x0B,0xA0); /* ISR register */
- value = inb(0xA0) & (irqmask >> 8);
- outb(0x0A,0xA0); /* back to the IRR register */
+ outb(0x0B,PIC_SLAVE_CMD); /* ISR register */
+ value = inb(PIC_SLAVE_CMD) & (irqmask >> 8);
+ outb(0x0A,PIC_SLAVE_CMD); /* back to the IRR register */
return value;
}
@@ -196,14 +198,14 @@
handle_real_irq:
if (irq & 8) {
- inb(0xA1); /* DUMMY - (do we need this?) */
- outb(cached_A1,0xA1);
- outb(0x60+(irq&7),0xA0);/* 'Specific EOI' to slave */
- outb(0x62,0x20); /* 'Specific EOI' to master-IRQ2 */
+ inb(PIC_SLAVE_IMR); /* DUMMY - (do we need this?) */
+ outb(cached_slave_mask, PIC_SLAVE_IMR);
+ outb(0x60+(irq&7),PIC_SLAVE_CMD);/* 'Specific EOI' to slave */
+ outb(0x60+PIC_CASCADE_IR,PIC_MASTER_CMD); /* 'Specific EOI' to master-IRQ2 */
} else {
- inb(0x21); /* DUMMY - (do we need this?) */
- outb(cached_21,0x21);
- outb(0x60+irq,0x20); /* 'Specific EOI' to master */
+ inb(PIC_MASTER_IMR); /* DUMMY - (do we need this?) */
+ outb(cached_master_mask, PIC_MASTER_IMR);
+ outb(0x60+irq,PIC_MASTER_CMD); /* 'Specific EOI to master */
}
spin_unlock_irqrestore(&i8259A_lock, flags);
return;
@@ -275,26 +277,24 @@
spin_lock_irqsave(&i8259A_lock, flags);
- outb(0xff, 0x21); /* mask all of 8259A-1 */
- outb(0xff, 0xA1); /* mask all of 8259A-2 */
+ outb(0xff, PIC_MASTER_IMR); /* mask all of 8259A-1 */
+ outb(0xff, PIC_SLAVE_IMR); /* mask all of 8259A-2 */
/*
* outb_p - this has to work on a wide range of PC hardware.
*/
- outb_p(0x11, 0x20); /* ICW1: select 8259A-1 init */
- outb_p(0x20 + 0, 0x21); /* ICW2: 8259A-1 IR0-7 mapped to 0x20-0x27 */
- outb_p(0x04, 0x21); /* 8259A-1 (the master) has a slave on IR2 */
- if (auto_eoi)
- outb_p(0x03, 0x21); /* master does Auto EOI */
- else
- outb_p(0x01, 0x21); /* master expects normal EOI */
-
- outb_p(0x11, 0xA0); /* ICW1: select 8259A-2 init */
- outb_p(0x20 + 8, 0xA1); /* ICW2: 8259A-2 IR0-7 mapped to 0x28-0x2f */
- outb_p(0x02, 0xA1); /* 8259A-2 is a slave on master's IR2 */
- outb_p(0x01, 0xA1); /* (slave's support for AEOI in flat mode
- is to be investigated) */
-
+ outb_p(0x11, PIC_MASTER_CMD); /* ICW1: select 8259A-1 init */
+ outb_p(0x20 + 0, PIC_MASTER_IMR); /* ICW2: 8259A-1 IR0-7 mapped to 0x20-0x27 */
+ outb_p(1U << PIC_CASCADE_IR, PIC_MASTER_IMR); /* 8259A-1 (the master) has a slave on IR2 */
+ if (auto_eoi) /* master does Auto EOI */
+ outb_p(MASTER_ICW4_DEFAULT | PIC_ICW4_AEOI, PIC_MASTER_IMR);
+ else /* master expects normal EOI */
+ outb_p(MASTER_ICW4_DEFAULT, PIC_MASTER_IMR);
+
+ outb_p(0x11, PIC_SLAVE_CMD); /* ICW1: select 8259A-2 init */
+ outb_p(0x20 + 8, PIC_SLAVE_IMR); /* ICW2: 8259A-2 IR0-7 mapped to 0x28-0x2f */
+ outb_p(PIC_CASCADE_IR, PIC_SLAVE_IMR); /* 8259A-2 is a slave on master's IR2 */
+ outb_p(SLAVE_ICW4_DEFAULT, PIC_SLAVE_IMR); /* (slave's support for AEOI in flat mode is to be investigated) */
if (auto_eoi)
/*
* in AEOI mode we just have to mask the interrupt
@@ -306,8 +306,8 @@
udelay(100); /* wait for 8259A to initialize */
- outb(cached_21, 0x21); /* restore master IRQ mask */
- outb(cached_A1, 0xA1); /* restore slave IRQ mask */
+ outb(cached_master_mask, PIC_MASTER_IMR); /* restore master IRQ mask */
+ outb(cached_slave_mask, PIC_SLAVE_IMR); /* restore slave IRQ mask */
spin_unlock_irqrestore(&i8259A_lock, flags);
}
@@ -324,11 +324,17 @@
* be shot.
*/
+/*
+ * =PC9800NOTE= In NEC PC-9800, we use irq8 instead of irq13!
+ */
+
static void math_error_irq(int cpl, void *dev_id, struct pt_regs *regs)
{
extern void math_error(void *);
+#ifndef CONFIG_PC9800
outb(0,0xF0);
- if (ignore_irq13 || !boot_cpu_data.hard_math)
+#endif
+ if (ignore_fpu_irq || !boot_cpu_data.hard_math)
return;
math_error((void *)regs->eip);
}
@@ -337,7 +343,7 @@
* New motherboards sometimes make IRQ 13 be a PCI interrupt,
* so allow interrupt sharing.
*/
-static struct irqaction irq13 = { math_error_irq, 0, 0, "fpu", NULL, NULL };
+static struct irqaction fpu_irq = { math_error_irq, 0, 0, "fpu", NULL, NULL };
void __init init_ISA_irqs (void)
{
@@ -393,14 +399,18 @@
* Set the clock to HZ Hz, we already have a valid
* vector now:
*/
- outb_p(0x34,0x43); /* binary, mode 2, LSB/MSB, ch 0 */
- outb_p(LATCH & 0xff , 0x40); /* LSB */
- outb(LATCH >> 8 , 0x40); /* MSB */
+ outb_p(0x34, PIT_MODE); /* binary, mode 2, LSB/MSB, ch 0 */
+ outb_p(LATCH & 0xff, PIT_CH0); /* LSB */
+ outb(LATCH >> 8 , PIT_CH0); /* MSB */
/*
* External FPU? Set up irq13 if so, for
* original braindamaged IBM FERR coupling.
*/
if (boot_cpu_data.hard_math && !cpu_has_fpu)
- setup_irq(13, &irq13);
+#ifndef CONFIG_PC9800
+ setup_irq(13, &fpu_irq);
+#else
+ setup_irq(8, &fpu_irq);
+#endif
}
diff -urN linux/arch/i386/kernel/pc9800_debug.c linux98/arch/i386/kernel/pc9800_debug.c
--- linux/arch/i386/kernel/pc9800_debug.c Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/kernel/pc9800_debug.c Wed May 1 16:47:15 2002
@@ -0,0 +1,362 @@
+/*
+ * linux/arch/i386/kernel/pc9800_debug.c
+ *
+ * Copyright (C) 1998 Linux/98 Project
+ *
+ * Revised by TAKAI Kousuke, Nov 1999.
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kdev_t.h>
+#include <linux/console.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+#include <asm/pc9800_debug.h>
+#include <asm/pc9800.h>
+
+unsigned char __pc9800_beep_flag = 0x7;
+
+/* pc9800_beep_{on|off|toggle} are moved to <asm/pc9800_debug.h>. */
+
+/* Normal CG window begins at physical address 0xA4000,
+ but user-definable characters are on odd address only... */
+#define UCG_WINDOW (phys_to_virt (0xA4001))
+
+#define UCG_MAX_SIZE (UCG_LOG_END - UCG_LOG_START + 1)
+
+#define UCG_CHAR_NR(x) ((x) / 32)
+#define UCG_2ND_BYTE(x) ((UCG_CHAR_NR (x) & 0x1f) + 0x80)
+#define UCG_1ST_BYTE(x) ((UCG_CHAR_NR (x) >> 5) + 0x76 - 0x20 + 0x80)
+#define UCG_LR(x) (((x) & 16) << 1)
+#define UCG_LR_MASK (1U << 5)
+#define UCG_OFFSET(x) ((x) % 16)
+
+#ifdef CONFIG_PC9800_UCGLOG
+/*
+ * Notes for PC-9800 UCG-log facility:
+ *
+ * Official specification of PC-9800 says they can have user-definable
+ * character-generator (UCG) RAM for 188 characters, but actual
+ * implementations appear to have 256 characters (`188' seems to come
+ * from adapting it to 94x94 character set). Thus there is 2KB-odd of
+ * unused area in UCG-RAM (one character consists of 16*16 dots, or
+ * 32 bytes). This area is not touched and its content will be preserved
+ * around system reset. This facility uses this area for saving
+ * kernel messages.
+ *
+ * UCG-RAM layout:
+ *
+ * Page Char Description
+ * ---- ---- ----------------------------------------------------
+ * 76 00 Magic string and character count in first 16 bytes
+ * 00 (remaining 16 bytes)
+ * : Log messages 1/2
+ * 1f
+ * 20 (unused)
+ * 21
+ * : Officially used for user-definable characters
+ * 7e
+ * 7f (unused)
+ * 77 00
+ * : Log messages 2/2
+ * 1f
+ * 20 (unused)
+ * 21
+ * : Officially used for user-definable characters
+ * 7e
+ * 7f (unused)
+ *
+ * + Characters 20--7f on each page seem to be initialized by
+ * system firmware. + */
+
+
+/* UCG-RAM offsets. */
+#define UCG_LOG_MAGIC 0
+#define UCG_LOG_HEAD 12
+#define UCG_LOG_SIZE 14
+#define UCG_LOG_START 16
+#define UCG_LOG_END (32 * 32 * 2 - 1)
+
+#define UCG_MAGIC_STRING "Linux/98"
+
+static unsigned int ucg_log_head = UCG_LOG_START;
+static unsigned int ucg_log_size = 0;
+
+static void
+ucglog_write(struct console *console, const char *buf, unsigned int length)
+{
+ unsigned char *const cg_window = UCG_WINDOW;
+
+ /*
+ * Note that we are called with interrupt disabled
+ * (spin_lock_irqsave in kernel/printk.c).
+ */
+
+ if ((ucg_log_size += length) > UCG_MAX_SIZE)
+ ucg_log_size = UCG_MAX_SIZE;
+
+ outb(0x0b, 0x68); /* bitmap access mode */
+
+ while (length) {
+ unsigned char *p;
+ unsigned int count;
+ u8 lr;
+
+ outb(UCG_2ND_BYTE (ucg_log_head), 0xa1);
+ outb(UCG_1ST_BYTE (ucg_log_head), 0xa3);
+ lr = UCG_LR(ucg_log_head);
+ do {
+ outb(lr, 0xa5);
+ p = cg_window + UCG_OFFSET(ucg_log_head) * 2;
+ count = 16 - UCG_OFFSET(ucg_log_head);
+ if (count > length)
+ count = length;
+ length -= count;
+ ucg_log_head += count;
+ do {
+ *p = *buf++;
+ p += 2;
+ } while (--count);
+ } while (length && (lr ^= UCG_LR_MASK));
+ }
+
+ if (ucg_log_head > UCG_LOG_END)
+ ucg_log_head = UCG_LOG_START;
+ outb(UCG_2ND_BYTE(UCG_LOG_HEAD), 0xa1);
+ outb(UCG_1ST_BYTE(UCG_LOG_HEAD), 0xa3);
+ outb(UCG_LR(UCG_LOG_HEAD), 0xa5);
+ cg_window[(UCG_OFFSET(UCG_LOG_HEAD)) * 2] = ucg_log_head;
+ cg_window[(UCG_OFFSET(UCG_LOG_HEAD) + 1) * 2] = ucg_log_head >> 8;
+#if UCG_CHAR_NR(UCG_LOG_HEAD) != UCG_CHAR_NR(UCG_LOG_SIZE)
+ outb(UCG_2ND_BYTE(UCG_LOG_SIZE), 0xa1);
+ outb(UCG_1ST_BYTE(UCG_LOG_SIZE), 0xa3);
+#endif
+#if UCG_LR(UCG_LOG_HEAD) != UCG_LR(UCG_LOG_SIZE)
+ outb(UCG_LR(UCG_LOG_SIZE), 0xa5);
+#endif
+ cg_window[(UCG_OFFSET(UCG_LOG_SIZE)) * 2] = ucg_log_size;
+ cg_window[(UCG_OFFSET(UCG_LOG_SIZE) + 1) * 2] = ucg_log_size >> 8;
+
+ outb(0x0a, 0x68);
+}
+
+static struct console ucglog_console = {
+ name: "ucg",
+ write: ucglog_write,
+ setup: NULL,
+ flags: CON_PRINTBUFFER,
+ index: -1,
+};
+
+static int __init
+ucglog_init(void)
+{
+ unsigned long flags;
+ const u8 *p;
+ u8 *cg_window;
+ static const union {
+ struct {
+ char magic[12];
+ u16 start;
+ u16 size;
+ } s;
+ u8 bytes[16];
+ } ucg_init_data __initdata = { { UCG_MAGIC_STRING, 0, 0 } };
+
+ if (PC9800_HIGHRESO_P()) {
+ /* Not implemented (yet)... */
+ return 0;
+ }
+
+ save_flags(flags);
+ cli();
+ outb(0x0b, 0x68); /* bitmap access mode */
+ outb(UCG_2ND_BYTE(UCG_LOG_MAGIC), 0xa1);
+ outb(UCG_1ST_BYTE(UCG_LOG_MAGIC), 0xa3);
+ outb(UCG_LR(UCG_LOG_MAGIC), 0xa5);
+ for (cg_window = UCG_WINDOW, p = ucg_init_data.bytes;
+ p < (&ucg_init_data + 1)->bytes; cg_window += 2)
+ *cg_window = *p++;
+ outb(0x0a, 0x68);
+ restore_flags(flags);
+
+ register_console(&ucglog_console);
+ printk(KERN_INFO "UCG-RAM console driver installed\n");
+ return 0;
+}
+
+__initcall (ucglog_init);
+
+#endif /* CONFIG_PC9800_UCGLOG */
+
+/*
+#define CONFIG_PC9800_UCGSAVEARGS
+*/
+
+#ifdef CONFIG_PC9800_UCGSAVEARGS
+
+#define UCG_SAVEARGS_START (1 * 32)
+
+void
+ucg_saveargs(unsigned int n, ...)
+{
+ u8 *cg;
+ unsigned int count;
+ unsigned int addr;
+ unsigned long flags;
+ const u8 *p = (const u8 *) (&n - 1);
+
+ save_flags(flags);
+ cli();
+ outb(0x0b, 0x68); /* bitmap access mode */
+ outb(UCG_2ND_BYTE(UCG_SAVEARGS_START), 0xa1);
+ outb(UCG_1ST_BYTE(UCG_SAVEARGS_START), 0xa3);
+ outb(UCG_LR(UCG_SAVEARGS_START), 0xa5);
+ for (cg = UCG_WINDOW, count = 0; count < 4; count++)
+ cg[count * 2] = p[count];
+
+ addr = UCG_SAVEARGS_START + 4;
+ for (p += 8; n--; p += 4) {
+ if (UCG_OFFSET(addr) == 0) {
+ outb(UCG_2ND_BYTE(addr), 0xa1);
+ outb(UCG_1ST_BYTE(addr), 0xa3);
+ outb(UCG_LR(addr), 0xa5);
+ }
+ cg[(UCG_OFFSET(addr) + 0) * 2] = p[0];
+ cg[(UCG_OFFSET(addr) + 1) * 2] = p[1];
+ cg[(UCG_OFFSET(addr) + 2) * 2] = p[2];
+ cg[(UCG_OFFSET(addr) + 3) * 2] = p[3];
+ addr += 4;
+ }
+
+ outb(UCG_2ND_BYTE(0), 0xa1);
+ outb(UCG_1ST_BYTE(0), 0xa3);
+ outb(UCG_LR(0), 0xa5);
+
+ outb(0x0a, 0x68);
+ restore_flags(flags);
+}
+#endif
+
+#ifdef CONFIG_PC9800_ASSERT
+void
+__assert_fail(const char *base_file, const char *file, unsigned int line,
+ const char *function, void *return_address, const char *expr)
+{
+ panic("In function `%s' (called from [<%p>])\n" KERN_EMERG
+ "%s%s%s%s:%u: Assertion `%s' failed.",
+ function, return_address, file,
+ base_file == file ? "" : " (",
+ base_file == file ? "" : base_file,
+ base_file == file ? "" : ")",
+ line, expr);
+}
+
+void
+__invalid_kernel_pointer(const char *base_file, const char *file,
+ unsigned int line, const char *function,
+ void *return_address,
+ const char *expr, void *val)
+{
+ panic("In function `%s' (called from [<%p>])\n" KERN_EMERG
+ "%s%s%s%s:%u: Invalid kernel pointer `%s' (%p).",
+ function, return_address, file,
+ base_file == file ? "" : " (",
+ base_file == file ? "" : base_file,
+ base_file == file ? "" : ")",
+ line, expr, val);
+}
+
+#endif /* CONFIG_PC9800_ASSERT */
+
+unsigned char pc9800_saveregs_enabled;
+
+__asm__ (".text\n"
+ " .global __pc9800_saveregs\n"
+ "__pc9800_saveregs:\n"
+#if 1
+ " pushfl\n"
+ " cmpb $0,pc9800_saveregs_enabled\n"
+ " je 1f\n"
+ " pushl %edi\n" /* reverse order of PUSHA */
+ " pushl %esi\n"
+ " pushl %ebp\n"
+ " leal 20(%esp),%esi\n" /* original ESP */
+ " pushl %esi\n"
+ " pushl %ebx\n"
+ " pushl %edx\n"
+ " pushl %ecx\n"
+ " pushl %eax\n"
+ " movl $0xc0000780,%edi\n" /* save few words on stack */
+ " movl $20, %ecx\n"
+ " cld; rep; ss; movsl\n" /* EDI becomes 0xC00007D0 */
+ " subl $(20+1+1+8)*4,%esi\n" /* ESI points EAX on stack */
+ " movl $8,%ecx\n"
+ " rep; ss; movsl\n" /* save GP registers */
+ " ss; lodsl\n" /* EFLAGS */
+ " ss; movsl\n" /* save EIP */
+ " stosl\n" /* save EFLAGS */
+ " movl %cr3,%eax\n" /* save control registers */
+ " stosl\n"
+ " movl %cr0,%eax\n"
+ " stosl\n"
+ " popl %eax\n"
+ " popl %ecx\n"
+ " addl $4*4,%esp\n" /* discard EDX/EBX/ESP/EBP */
+ " popl %esi\n"
+ " popl %edi\n"
+ "1: popfl\n"
+#else
+ " cmpb $0,pc9800_saveregs_enabled\n"
+ " je 1f\n"
+ " pushl %eax\n"
+ " movl %eax,0xc00007d0\n"
+ " movl %ecx,0xc00007d4\n"
+ " movl %edx,0xc00007d8\n"
+ " movl %ebx,0xc00007dc\n"
+ " leal 8(%esp),%eax\n" /* original ESP */
+ " movl %eax,0xc00007e0\n"
+ " movl %ebp,0xc00007e4\n"
+ " movl %esi,0xc00007e8\n"
+ " movl %edi,0xc00007ec\n"
+ " movl 4(%esp),%eax\n" /* EIP as return address */
+ " movl %eax,0xc00007f0\n"
+ " pushfl\n"
+ " popl %eax\n"
+ " movl %eax,0xc00007f4\n"
+ " movl %cr3,%eax\n"
+ " movl %eax,0xc00007f8\n"
+ " movl %cr0,%eax\n"
+ " movl %eax,0xc00007fc\n"
+ " pushl %ecx\n"
+ " pushl %esi\n"
+ " pushl %edi\n"
+ " leal 20(%esp),%esi\n"
+ " movl $0xc0000780,%edi\n"
+ " movl $16,%ecx\n"
+ " cld; rep; ss; movsl\n"
+ " popl %edi\n"
+ " popl %esi\n"
+ " popl %ecx\n"
+ " popl %eax\n"
+ "1:\n"
+#endif
+ " ret");
+
+__asm__ (".weak mcount; mcount = __pc9800_saveregs");
+
+#if 0
+int
+test_mcount(void)
+{
+ printk("Calling mcount...\n");
+ pc9800_saveregs_enabled = 1;
+ mcount();
+}
+
+__initcall (test_mcount);
+#endif
diff -urN linux/arch/i386/kernel/reboot.c linux98/arch/i386/kernel/reboot.c
--- linux/arch/i386/kernel/reboot.c Sat Oct 19 13:01:20 2002
+++ linux98/arch/i386/kernel/reboot.c Sun Oct 20 14:59:44 2002
@@ -8,6 +8,7 @@
#include <linux/interrupt.h>
#include <linux/mc146818rtc.h>
#include <asm/uaccess.h>
+#include "mach_reboot.h"
/*
* Power off function, if any
@@ -125,15 +126,6 @@
0xea, 0x00, 0x00, 0xff, 0xff /* ljmp $0xffff,$0x0000 */
};
-static inline void kb_wait(void)
-{
- int i;
-
- for (i=0; i<0x10000; i++)
- if ((inb_p(0x64) & 0x02) == 0)
- break;
-}
-
/*
* Switch to real mode and then execute the code
* specified by the code and length parameters.
@@ -264,13 +256,7 @@
/* rebooting needs to touch the page at absolute addr 0 */
*((unsigned short *)__va(0x472)) = reboot_mode;
for (;;) {
- int i;
- for (i=0; i<100; i++) {
- kb_wait();
- udelay(50);
- outb(0xfe,0x64); /* pulse reset low */
- udelay(50);
- }
+ mach_reboot();
/* That didn't work - force a triple fault.. */
__asm__ __volatile__("lidt %0": :"m" (no_idt));
__asm__ __volatile__("int3");
diff -urN linux/arch/i386/kernel/setup.c linux98/arch/i386/kernel/setup.c
--- linux/arch/i386/kernel/setup.c Thu Oct 31 13:23:02 2002
+++ linux98/arch/i386/kernel/setup.c Thu Oct 31 13:50:50 2002
@@ -20,6 +20,7 @@
* This file handles the architecture-dependent parts of initialization
*/
+#include <linux/config.h>
#include <linux/sched.h>
#include <linux/mm.h>
#include <linux/tty.h>
@@ -40,6 +41,7 @@
#include <asm/setup.h>
#include <asm/arch_hooks.h>
#include "setup_arch_pre.h"
+#include "mach_resources.h"
static inline char * __init machine_specific_memory_setup(void);
@@ -47,7 +49,7 @@
* Machine setup..
*/
-char ignore_irq13; /* set if exception 16 works */
+char ignore_fpu_irq; /* set if exception 16 works */
struct cpuinfo_x86 boot_cpu_data = { 0, 0, 0, 0, -1, 1, 0, 0, -1 };
unsigned long mmu_cr4_features;
@@ -98,98 +100,8 @@
static char command_line[COMMAND_LINE_SIZE];
char saved_command_line[COMMAND_LINE_SIZE];
-struct resource standard_io_resources[] = {
- { "dma1", 0x00, 0x1f, IORESOURCE_BUSY },
- { "pic1", 0x20, 0x3f, IORESOURCE_BUSY },
- { "timer", 0x40, 0x5f, IORESOURCE_BUSY },
- { "keyboard", 0x60, 0x6f, IORESOURCE_BUSY },
- { "dma page reg", 0x80, 0x8f, IORESOURCE_BUSY },
- { "pic2", 0xa0, 0xbf, IORESOURCE_BUSY },
- { "dma2", 0xc0, 0xdf, IORESOURCE_BUSY },
- { "fpu", 0xf0, 0xff, IORESOURCE_BUSY }
-};
-#ifdef CONFIG_MELAN
-standard_io_resources[1] = { "pic1", 0x20, 0x21, IORESOURCE_BUSY };
-standard_io_resources[5] = { "pic2", 0xa0, 0xa1, IORESOURCE_BUSY };
-#endif
-
-#define STANDARD_IO_RESOURCES (sizeof(standard_io_resources)/sizeof(struct resource))
-
static struct resource code_resource = { "Kernel code", 0x100000, 0 };
static struct resource data_resource = { "Kernel data", 0, 0 };
-static struct resource vram_resource = { "Video RAM area", 0xa0000, 0xbffff, IORESOURCE_BUSY };
-
-/* System ROM resources */
-#define MAXROMS 6
-static struct resource rom_resources[MAXROMS] = {
- { "System ROM", 0xF0000, 0xFFFFF, IORESOURCE_BUSY },
- { "Video ROM", 0xc0000, 0xc7fff, IORESOURCE_BUSY }
-};
-
-#define romsignature(x) (*(unsigned short *)(x) == 0xaa55)
-
-static void __init probe_roms(void)
-{
- int roms = 1;
- unsigned long base;
- unsigned char *romstart;
-
- request_resource(&iomem_resource, rom_resources+0);
-
- /* Video ROM is standard at C000:0000 - C7FF:0000, check signature */
- for (base = 0xC0000; base < 0xE0000; base += 2048) {
- romstart = isa_bus_to_virt(base);
- if (!romsignature(romstart))
- continue;
- request_resource(&iomem_resource, rom_resources + roms);
- roms++;
- break;
- }
-
- /* Extension roms at C800:0000 - DFFF:0000 */
- for (base = 0xC8000; base < 0xE0000; base += 2048) {
- unsigned long length;
-
- romstart = isa_bus_to_virt(base);
- if (!romsignature(romstart))
- continue;
- length = romstart[2] * 512;
- if (length) {
- unsigned int i;
- unsigned char chksum;
-
- chksum = 0;
- for (i = 0; i < length; i++)
- chksum += romstart[i];
-
- /* Good checksum? */
- if (!chksum) {
- rom_resources[roms].start = base;
- rom_resources[roms].end = base + length - 1;
- rom_resources[roms].name = "Extension ROM";
- rom_resources[roms].flags = IORESOURCE_BUSY;
-
- request_resource(&iomem_resource, rom_resources + roms);
- roms++;
- if (roms >= MAXROMS)
- return;
- }
- }
- }
-
- /* Final check for motherboard extension rom at E000:0000 */
- base = 0xE0000;
- romstart = isa_bus_to_virt(base);
-
- if (romsignature(romstart)) {
- rom_resources[roms].start = base;
- rom_resources[roms].end = base + 65535;
- rom_resources[roms].name = "Extension ROM";
- rom_resources[roms].flags = IORESOURCE_BUSY;
-
- request_resource(&iomem_resource, rom_resources + roms);
- }
-}
static void __init limit_regions (unsigned long long size)
{
@@ -821,11 +733,8 @@
request_resource(res, &data_resource);
}
}
- request_resource(&iomem_resource, &vram_resource);
- /* request I/O space for devices used on all i[345]86 PCs */
- for (i = 0; i < STANDARD_IO_RESOURCES; i++)
- request_resource(&ioport_resource, standard_io_resources+i);
+ mach_request_resource( );
/* Tell the PCI layer not to allocate too close to the RAM area.. */
low_mem_size = ((max_low_pfn << PAGE_SHIFT) + 0xfffff) & ~0xfffff;
@@ -905,6 +814,8 @@
#ifdef CONFIG_VT
#if defined(CONFIG_VGA_CONSOLE)
conswitchp = &vga_con;
+#elif defined(CONFIG_GDC_CONSOLE)
+ conswitchp = &gdc_con;
#elif defined(CONFIG_DUMMY_CONSOLE)
conswitchp = &dummy_con;
#endif
diff -urN linux/arch/i386/kernel/time.c linux98/arch/i386/kernel/time.c
--- linux/arch/i386/kernel/time.c Sat Oct 19 13:01:53 2002
+++ linux98/arch/i386/kernel/time.c Sun Oct 20 19:57:14 2002
@@ -54,12 +54,15 @@
#include <asm/processor.h>
#include <asm/timer.h>
-#include <linux/mc146818rtc.h>
+#include "mach_time.h"
+
#include <linux/timex.h>
#include <linux/config.h>
#include <asm/arch_hooks.h>
+#include "io_ports.h"
+
extern spinlock_t i8259A_lock;
#include "do_timer.h"
@@ -133,69 +136,13 @@
write_unlock_irq(&xtime_lock);
}
-/*
- * In order to set the CMOS clock precisely, set_rtc_mmss has to be
- * called 500 ms after the second nowtime has started, because when
- * nowtime is written into the registers of the CMOS clock, it will
- * jump to the next second precisely 500 ms later. Check the Motorola
- * MC146818A or Dallas DS12887 data sheet for details.
- *
- * BUG: This routine does not handle hour overflow properly; it just
- * sets the minutes. Usually you'll only notice that after reboot!
- */
static int set_rtc_mmss(unsigned long nowtime)
{
- int retval = 0;
- int real_seconds, real_minutes, cmos_minutes;
- unsigned char save_control, save_freq_select;
+ int retval;
/* gets recalled with irq locally disabled */
spin_lock(&rtc_lock);
- save_control = CMOS_READ(RTC_CONTROL); /* tell the clock it's being set */
- CMOS_WRITE((save_control|RTC_SET), RTC_CONTROL);
-
- save_freq_select = CMOS_READ(RTC_FREQ_SELECT); /* stop and reset prescaler */
- CMOS_WRITE((save_freq_select|RTC_DIV_RESET2), RTC_FREQ_SELECT);
-
- cmos_minutes = CMOS_READ(RTC_MINUTES);
- if (!(save_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD)
- BCD_TO_BIN(cmos_minutes);
-
- /*
- * since we're only adjusting minutes and seconds,
- * don't interfere with hour overflow. This avoids
- * messing with unknown time zones but requires your
- * RTC not to be off by more than 15 minutes
- */
- real_seconds = nowtime % 60;
- real_minutes = nowtime / 60;
- if (((abs(real_minutes - cmos_minutes) + 15)/30) & 1)
- real_minutes += 30; /* correct for half hour time zone */
- real_minutes %= 60;
-
- if (abs(real_minutes - cmos_minutes) < 30) {
- if (!(save_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD) {
- BIN_TO_BCD(real_seconds);
- BIN_TO_BCD(real_minutes);
- }
- CMOS_WRITE(real_seconds,RTC_SECONDS);
- CMOS_WRITE(real_minutes,RTC_MINUTES);
- } else {
- printk(KERN_WARNING
- "set_rtc_mmss: can't update from %d to %d\n",
- cmos_minutes, real_minutes);
- retval = -1;
- }
-
- /* The following flags have to be released exactly in this order,
- * otherwise the DS12887 (popular MC146818A clone with integrated
- * battery and quartz) will not reset the oscillator and will not
- * update precisely 500 ms later. You won't find this mentioned in
- * the Dallas Semiconductor data sheets, but who believes data
- * sheets anyway ... -- Markus Kuhn
- */
- CMOS_WRITE(save_control, RTC_CONTROL);
- CMOS_WRITE(save_freq_select, RTC_FREQ_SELECT);
+ retval = mach_set_rtc_mmss(nowtime);
spin_unlock(&rtc_lock);
return retval;
@@ -221,9 +168,9 @@
* on an 82489DX-based system.
*/
spin_lock(&i8259A_lock);
- outb(0x0c, 0x20);
+ outb(0x0c, PIC_MASTER_OCW3);
/* Ack the IRQ; AEOI will end it automatically. */
- inb(0x20);
+ inb(PIC_MASTER_POLL);
spin_unlock(&i8259A_lock);
}
#endif
@@ -237,14 +184,14 @@
*/
if ((time_status & STA_UNSYNC) == 0 &&
xtime.tv_sec > last_rtc_update + 660 &&
- (xtime.tv_nsec / 1000) >= 500000 - ((unsigned) TICK_SIZE) / 2 &&
- (xtime.tv_nsec / 1000) <= 500000 + ((unsigned) TICK_SIZE) / 2) {
+ (xtime.tv_nsec / 1000) >= TIME1 - ((unsigned) TICK_SIZE) / 2 &&
+ (xtime.tv_nsec / 1000) <= TIME2 + ((unsigned) TICK_SIZE) / 2) {
if (set_rtc_mmss(xtime.tv_sec) == 0)
last_rtc_update = xtime.tv_sec;
else
last_rtc_update = xtime.tv_sec - 600; /* do it again in 60 s */
}
- +
#ifdef CONFIG_MCA
if( MCA_bus ) {
/* The PS/2 uses level-triggered interrupts. You can't
@@ -289,43 +236,15 @@
/* not static: needed by APM */
unsigned long get_cmos_time(void)
{
- unsigned int year, mon, day, hour, min, sec;
- int i;
+ unsigned long retval;
spin_lock(&rtc_lock);
- /* The Linux interpretation of the CMOS clock register contents:
- * When the Update-In-Progress (UIP) flag goes from 1 to 0, the
- * RTC registers show the second which has precisely just started.
- * Let's hope other operating systems interpret the RTC the same way.
- */
- /* read RTC exactly on falling edge of update flag */
- for (i = 0 ; i < 1000000 ; i++) /* may take up to 1 second... */
- if (CMOS_READ(RTC_FREQ_SELECT) & RTC_UIP)
- break;
- for (i = 0 ; i < 1000000 ; i++) /* must try at least 2.228 ms */
- if (!(CMOS_READ(RTC_FREQ_SELECT) & RTC_UIP))
- break;
- do { /* Isn't this overkill ? UIP above should guarantee consistency */
- sec = CMOS_READ(RTC_SECONDS);
- min = CMOS_READ(RTC_MINUTES);
- hour = CMOS_READ(RTC_HOURS);
- day = CMOS_READ(RTC_DAY_OF_MONTH);
- mon = CMOS_READ(RTC_MONTH);
- year = CMOS_READ(RTC_YEAR);
- } while (sec != CMOS_READ(RTC_SECONDS));
- if (!(CMOS_READ(RTC_CONTROL) & RTC_DM_BINARY) || RTC_ALWAYS_BCD)
- {
- BCD_TO_BIN(sec);
- BCD_TO_BIN(min);
- BCD_TO_BIN(hour);
- BCD_TO_BIN(day);
- BCD_TO_BIN(mon);
- BCD_TO_BIN(year);
- }
+
+ retval = mach_get_cmos_time();
+
spin_unlock(&rtc_lock);
- if ((year += 1900) < 1970)
- year += 100;
- return mktime(year, mon, day, hour, min, sec);
+
+ return retval;
}
/* XXX this driverfs stuff should probably go elsewhere later -john */
diff -urN linux/arch/i386/kernel/timers/timer_pit.c linux98/arch/i386/kernel/timers/timer_pit.c
--- linux/arch/i386/kernel/timers/timer_pit.c Sat Oct 19 13:02:29 2002
+++ linux98/arch/i386/kernel/timers/timer_pit.c Mon Oct 21 11:39:53 2002
@@ -13,6 +13,7 @@
extern spinlock_t i8259A_lock;
extern spinlock_t i8253_lock;
#include "do_timer.h"
+#include "io_ports.h"
static int init_pit(void)
{
@@ -61,7 +62,8 @@
{
int count;
- static int count_p = LATCH; /* for the first call after boot */
+ static int count_p;
+ static int is_1st_boot = 1; /* for the first call after boot */
static unsigned long jiffies_p = 0;
/*
@@ -69,12 +71,18 @@
*/
unsigned long jiffies_t;
+ /* for support LATCH is not constant */
+ if (is_1st_boot) {
+ is_1st_boot = 0;
+ count_p = LATCH;
+ }
+
/* gets recalled with irq locally disabled */
spin_lock(&i8253_lock);
/* timer count may underflow right here */
- outb_p(0x00, 0x43); /* latch the count ASAP */
+ outb_p(0x00, PIT_MODE); /* latch the count ASAP */
- count = inb_p(0x40); /* read the latched count */
+ count = inb_p(PIT_CH0); /* read the latched count */
/*
* We do this guaranteed double memory access instead of a _p @@ -82,13 +90,13 @@
*/
jiffies_t = jiffies;
- count |= inb_p(0x40) << 8;
+ count |= inb_p(PIT_CH0) << 8;

/* VIA686a test code... reset the latch if count > max + 1 */
if (count > LATCH) {
- outb_p(0x34, 0x43);
- outb_p(LATCH & 0xff, 0x40);
- outb(LATCH >> 8, 0x40);
+ outb_p(0x34, PIT_MODE);
+ outb_p(LATCH & 0xff, PIT_CH0);
+ outb(LATCH >> 8, PIT_CH0);
count = LATCH - 1;
}

diff -urN linux/arch/i386/kernel/timers/timer_tsc.c linux98/arch/i386/kernel/timers/timer_tsc.c
--- linux/arch/i386/kernel/timers/timer_tsc.c Sat Oct 19 13:02:24 2002
+++ linux98/arch/i386/kernel/timers/timer_tsc.c Sun Oct 20 22:48:53 2002
@@ -12,6 +12,9 @@
#include <asm/timer.h>
#include <asm/io.h>
+#include "io_ports.h"
+#include "calibrate_tsc.h"
+
extern int x86_udelay_tsc;
extern spinlock_t i8253_lock;
@@ -19,8 +22,6 @@
/* Number of usecs that the last interrupt was delayed */
static int delay_at_last_interrupt;
-static unsigned long last_tsc_low; /* lsb 32 bits of Time Stamp Counter */
-
/* Cached *multiplier* to convert TSC counts to microseconds.
* (see the equation below).
* Equal to 2^32 * (1 / (clocks per usec) ).
@@ -77,10 +78,10 @@
rdtscl(last_tsc_low);
spin_lock(&i8253_lock);
- outb_p(0x00, 0x43); /* latch the count ASAP */
+ outb_p(0x00, PIT_MODE); /* latch the count ASAP */
- count = inb_p(0x40); /* read the latched count */
- count |= inb(0x40) << 8;
+ count = inb_p(PIT_CH0); /* read the latched count */
+ count |= inb(PIT_CH0) << 8;
spin_unlock(&i8253_lock);
count = ((LATCH-1) - count) * TICK_SIZE;
@@ -88,83 +89,6 @@
}
-/* ------ Calibrate the TSC ------- - * Return 2^32 * (1 / (TSC clocks per usec)) for do_fast_gettimeoffset().
- * Too much 64-bit arithmetic here to do this cleanly in C, and for
- * accuracy's sake we want to keep the overhead on the CTC speaker (channel 2)
- * output busy loop as low as possible. We avoid reading the CTC registers
- * directly because of the awkward 8-bit access mechanism of the 82C54
- * device.
- */
-
-#define CALIBRATE_LATCH (5 * LATCH)
-#define CALIBRATE_TIME (5 * 1000020/HZ)
-
-static unsigned long __init calibrate_tsc(void)
-{
- /* Set the Gate high, disable speaker */
- outb((inb(0x61) & ~0x02) | 0x01, 0x61);
-
- /*
- * Now let's take care of CTC channel 2
- *
- * Set the Gate high, program CTC channel 2 for mode 0,
- * (interrupt on terminal count mode), binary count,
- * load 5 * LATCH count, (LSB and MSB) to begin countdown.
- */
- outb(0xb0, 0x43); /* binary, mode 0, LSB/MSB, Ch 2 */
- outb(CALIBRATE_LATCH & 0xff, 0x42); /* LSB of count */
- outb(CALIBRATE_LATCH >> 8, 0x42); /* MSB of count */
-
- {
- unsigned long startlow, starthigh;
- unsigned long endlow, endhigh;
- unsigned long count;
-
- rdtsc(startlow,starthigh);
- count = 0;
- do {
- count++;
- } while ((inb(0x61) & 0x20) == 0);
- rdtsc(endlow,endhigh);
-
- last_tsc_low = endlow;
-
- /* Error: ECTCNEVERSET */
- if (count <= 1)
- goto bad_ctc;
-
- /* 64-bit subtract - gcc just messes up with long longs */
- __asm__("subl %2,%0\n\t"
- "sbbl %3,%1"
- :"=a" (endlow), "=d" (endhigh)
- :"g" (startlow), "g" (starthigh),
- "0" (endlow), "1" (endhigh));
-
- /* Error: ECPUTOOFAST */
- if (endhigh)
- goto bad_ctc;
-
- /* Error: ECPUTOOSLOW */
- if (endlow <= CALIBRATE_TIME)
- goto bad_ctc;
-
- __asm__("divl %2"
- :"=a" (endlow), "=d" (endhigh)
- :"r" (endlow), "0" (0), "1" (CALIBRATE_TIME));
-
- return endlow;
- }
-
- /*
- * The CTC wasn't reliable: we got a hit on the very first read,
- * or the CPU was so fast/slow that the quotient wouldn't fit in
- * 32 bits..
- */
-bad_ctc:
- return 0;
-}
-
#ifdef CONFIG_CPU_FREQ
diff -urN linux/arch/i386/kernel/traps.c linux98/arch/i386/kernel/traps.c
--- linux/arch/i386/kernel/traps.c Sat Oct 19 13:01:16 2002
+++ linux98/arch/i386/kernel/traps.c Mon Oct 21 00:25:38 2002
@@ -49,6 +49,8 @@
#include <linux/irq.h>
#include <linux/module.h>
+#include "mach_traps.h"
+
asmlinkage int system_call(void);
asmlinkage void lcall7(void);
asmlinkage void lcall27(void);
@@ -449,11 +451,10 @@
printk("You probably have a hardware problem with your RAM chips\n");
/* Clear and disable the memory parity error line. */
- reason = (reason & 0xf) | 4;
- outb(reason, 0x61);
+ clear_mem_error(reason);
}
-static void io_check_error(unsigned char reason, struct pt_regs * regs)
+static inline void io_check_error(unsigned char reason, struct pt_regs * regs)
{
unsigned long i;
@@ -487,8 +488,9 @@
static void default_do_nmi(struct pt_regs * regs)
{
- unsigned char reason = inb(0x61);
+ unsigned char reason;
+ reason = get_nmi_reason();
if (!(reason & 0xc0)) {
#if CONFIG_X86_LOCAL_APIC
/*
@@ -506,15 +508,12 @@
if (reason & 0x80)
mem_parity_error(reason, regs);
if (reason & 0x40)
- io_check_error(reason, regs);
+ HANDLE_REASON_0X40(reason, regs);
/*
* Reassert NMI in case it became active meanwhile
* as it's edge-triggered.
*/
- outb(0x8f, 0x70);
- inb(0x71); /* dummy */
- outb(0x0f, 0x70);
- inb(0x71); /* dummy */
+ reassert_nmi();
}
static int dummy_nmi_callback(struct pt_regs * regs, int cpu)
@@ -697,7 +696,7 @@
asmlinkage void do_coprocessor_error(struct pt_regs * regs, long error_code)
{
- ignore_irq13 = 1;
+ ignore_fpu_irq = 1;
math_error((void *)regs->eip);
}
@@ -754,7 +753,7 @@
{
if (cpu_has_xmm) {
/* Handle SIMD FPU exceptions on PIII+ processors. */
- ignore_irq13 = 1;
+ ignore_fpu_irq = 1;
simd_math_error((void *)regs->eip);
} else {
/*
diff -urN linux/arch/i386/kernel/vm86.c linux98/arch/i386/kernel/vm86.c
--- linux/arch/i386/kernel/vm86.c Sat Oct 12 13:21:31 2002
+++ linux98/arch/i386/kernel/vm86.c Sat Oct 12 16:09:20 2002
@@ -30,6 +30,7 @@
*
*/
+#include <linux/config.h>
#include <linux/errno.h>
#include <linux/sched.h>
#include <linux/kernel.h>
@@ -732,10 +733,22 @@
free_vm86_irq(i);
}
+#ifndef CONFIG_PC9800
+# define ILLEGAL_IRQ(irq) ((irq) < 3 || (irq) > 15)
+# define FIRST_VM86_IRQ 3
+#else
+/*
+ * On PC-9800, slave PIC is wired master PIC's IR7,
+ * so that we don't allow vm86 to grab IRQ7.
+ */
+# define ILLEGAL_IRQ(irq) ((irq) < 2 || (irq) == 7 || (irq) > 15)
+# define FIRST_VM86_IRQ 2
+#endif
+
static inline void handle_irq_zombies(void)
{
int i;
- for (i=3; i<16; i++) {
+ for (i=FIRST_VM86_IRQ; i<16; i++) {
if (vm86_irqs[i].tsk) {
if (task_valid(vm86_irqs[i].tsk)) continue;
free_vm86_irq(i);
@@ -748,7 +761,7 @@
int bit;
unsigned long flags;

- if ( (irqnumber<3) || (irqnumber>15) ) return 0;
+ if (ILLEGAL_IRQ(irqnumber)) return 0;
if (vm86_irqs[irqnumber].tsk != current) return 0;
spin_lock_irqsave(&irqbits_lock, flags);
bit = irqbits & (1 << irqnumber);
@@ -774,7 +787,7 @@
handle_irq_zombies();
if (!capable(CAP_SYS_ADMIN)) return -EPERM;
if (!((1 << sig) & ALLOWED_SIGS)) return -EPERM;
- if ( (irq<3) || (irq>15) ) return -EPERM;
+ if (ILLEGAL_IRQ(irq)) return -EPERM;
if (vm86_irqs[irq].tsk) return -EPERM;
ret = request_irq(irq, &irq_handler, 0, VM86_IRQNAME, 0);
if (ret) return ret;
@@ -784,7 +797,7 @@
}
case VM86_FREE_IRQ: {
handle_irq_zombies();
- if ( (irqnumber<3) || (irqnumber>15) ) return -EPERM;
+ if (ILLEGAL_IRQ(irqnumber)) return -EPERM;
if (!vm86_irqs[irqnumber].tsk) return 0;
if (vm86_irqs[irqnumber].tsk != current) return -EPERM;
free_vm86_irq(irqnumber);
diff -urN linux/arch/i386/mach-generic/calibrate_tsc.h linux98/arch/i386/mach-generic/calibrate_tsc.h
--- linux/arch/i386/mach-generic/calibrate_tsc.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-generic/calibrate_tsc.h Mon Oct 21 09:30:16 2002
@@ -0,0 +1,88 @@
+/*
+ * arch/i386/mach-generic/calibrate_tsc.h
+ *
+ * Machine specific calibrate_tsc() for generic.
+ * Split out from timer_tsc.c by Osamu Tomita <tomita@cinet.co.jp>
+ */
+/* ------ Calibrate the TSC ------- + * Return 2^32 * (1 / (TSC clocks per usec)) for do_fast_gettimeoffset().
+ * Too much 64-bit arithmetic here to do this cleanly in C, and for
+ * accuracy's sake we want to keep the overhead on the CTC speaker (channel 2)
+ * output busy loop as low as possible. We avoid reading the CTC registers
+ * directly because of the awkward 8-bit access mechanism of the 82C54
+ * device.
+ */
+#ifndef _MACH_CALIBRATE_TSC_H
+#define _MACH_CALIBRATE_TSC_H
+
+#define CALIBRATE_LATCH (5 * LATCH)
+#define CALIBRATE_TIME (5 * 1000020/HZ)
+
+static unsigned long last_tsc_low; /* lsb 32 bits of Time Stamp Counter */
+
+static inline unsigned long calibrate_tsc(void)
+{
+ /* Set the Gate high, disable speaker */
+ outb((inb(0x61) & ~0x02) | 0x01, 0x61);
+
+ /*
+ * Now let's take care of CTC channel 2
+ *
+ * Set the Gate high, program CTC channel 2 for mode 0,
+ * (interrupt on terminal count mode), binary count,
+ * load 5 * LATCH count, (LSB and MSB) to begin countdown.
+ */
+ outb(0xb0, PIT_MODE); /* binary, mode 0, LSB/MSB, Ch 2 */
+ outb(CALIBRATE_LATCH & 0xff, PIT_CH2); /* LSB of count */
+ outb(CALIBRATE_LATCH >> 8, PIT_CH2); /* MSB of count */
+
+ {
+ unsigned long startlow, starthigh;
+ unsigned long endlow, endhigh;
+ unsigned long count;
+
+ rdtsc(startlow,starthigh);
+ count = 0;
+ do {
+ count++;
+ } while ((inb(0x61) & 0x20) == 0);
+ rdtsc(endlow,endhigh);
+
+ last_tsc_low = endlow;
+
+ /* Error: ECTCNEVERSET */
+ if (count <= 1)
+ goto bad_ctc;
+
+ /* 64-bit subtract - gcc just messes up with long longs */
+ __asm__("subl %2,%0\n\t"
+ "sbbl %3,%1"
+ :"=a" (endlow), "=d" (endhigh)
+ :"g" (startlow), "g" (starthigh),
+ "0" (endlow), "1" (endhigh));
+
+ /* Error: ECPUTOOFAST */
+ if (endhigh)
+ goto bad_ctc;
+
+ /* Error: ECPUTOOSLOW */
+ if (endlow <= CALIBRATE_TIME)
+ goto bad_ctc;
+
+ __asm__("divl %2"
+ :"=a" (endlow), "=d" (endhigh)
+ :"r" (endlow), "0" (0), "1" (CALIBRATE_TIME));
+
+ return endlow;
+ }
+
+ /*
+ * The CTC wasn't reliable: we got a hit on the very first read,
+ * or the CPU was so fast/slow that the quotient wouldn't fit in
+ * 32 bits..
+ */
+bad_ctc:
+ return 0;
+}
+
+#endif /* !_MACH_CALIBRATE_TSC_H */
diff -urN linux/arch/i386/mach-generic/io_ports.h linux98/arch/i386/mach-generic/io_ports.h
--- linux/arch/i386/mach-generic/io_ports.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-generic/io_ports.h Mon Oct 21 09:47:38 2002
@@ -0,0 +1,30 @@
+/*
+ * arch/i386/mach-generic/io_ports.h
+ *
+ * Machine specific IO port address definition for generic.
+ * Written by Osamu Tomita <tomita@cinet.co.jp>
+ */
+#ifndef _MACH_IO_PORTS_H
+#define _MACH_IO_PORTS_H
+
+/* i8253A PIT registers */
+#define PIT_MODE 0x43
+#define PIT_CH0 0x40
+#define PIT_CH2 0x42
+
+/* i8259A PIC registers */
+#define PIC_MASTER_CMD 0x20
+#define PIC_MASTER_IMR 0x21
+#define PIC_MASTER_ISR PIC_MASTER_CMD
+#define PIC_MASTER_POLL PIC_MASTER_ISR
+#define PIC_MASTER_OCW3 PIC_MASTER_ISR
+#define PIC_SLAVE_CMD 0xa0
+#define PIC_SLAVE_IMR 0xa1
+
+/* i8259A PIC related value */
+#define PIC_CASCADE_IR 2
+#define MASTER_ICW4_DEFAULT 0x01
+#define SLAVE_ICW4_DEFAULT 0x01
+#define PIC_ICW4_AEOI 2
+
+#endif /* !_MACH_IO_PORTS_H */
diff -urN linux/arch/i386/mach-generic/mach_reboot.h linux98/arch/i386/mach-generic/mach_reboot.h
--- linux/arch/i386/mach-generic/mach_reboot.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-generic/mach_reboot.h Mon Oct 21 09:53:44 2002
@@ -0,0 +1,30 @@
+/*
+ * arch/i386/mach-generic/mach_reboot.h
+ *
+ * Machine specific reboot functions for generic.
+ * Split out from reboot.c by Osamu Tomita <tomita@cinet.co.jp>
+ */
+#ifndef _MACH_REBOOT_H
+#define _MACH_REBOOT_H
+
+static inline void kb_wait(void)
+{
+ int i;
+
+ for (i = 0; i < 0x10000; i++)
+ if ((inb_p(0x64) & 0x02) == 0)
+ break;
+}
+
+static inline void mach_reboot(void)
+{
+ int i;
+ for (i = 0; i < 100; i++) {
+ kb_wait();
+ udelay(50);
+ outb(0xfe, 0x64); /* pulse reset low */
+ udelay(50);
+ }
+}
+
+#endif /* !_MACH_REBOOT_H */
diff -urN linux/arch/i386/mach-generic/mach_resources.h linux98/arch/i386/mach-generic/mach_resources.h
--- linux/arch/i386/mach-generic/mach_resources.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-generic/mach_resources.h Mon Oct 21 09:59:22 2002
@@ -0,0 +1,113 @@
+/*
+ * arch/i386/mach-generic/mach_resources.h
+ *
+ * Machine specific resource allocation for generic.
+ * Split out from setup.c by Osamu Tomita <tomita@cinet.co.jp>
+ */
+#ifndef _MACH_RESOURCES_H
+#define _MACH_RESOURCES_H
+
+struct resource standard_io_resources[] = {
+ { "dma1", 0x00, 0x1f, IORESOURCE_BUSY },
+ { "pic1", 0x20, 0x3f, IORESOURCE_BUSY },
+ { "timer", 0x40, 0x5f, IORESOURCE_BUSY },
+ { "keyboard", 0x60, 0x6f, IORESOURCE_BUSY },
+ { "dma page reg", 0x80, 0x8f, IORESOURCE_BUSY },
+ { "pic2", 0xa0, 0xbf, IORESOURCE_BUSY },
+ { "dma2", 0xc0, 0xdf, IORESOURCE_BUSY },
+ { "fpu", 0xf0, 0xff, IORESOURCE_BUSY }
+};
+#ifdef CONFIG_MELAN
+standard_io_resources[1] = { "pic1", 0x20, 0x21, IORESOURCE_BUSY };
+standard_io_resources[5] = { "pic2", 0xa0, 0xa1, IORESOURCE_BUSY };
+#endif
+
+#define STANDARD_IO_RESOURCES (sizeof(standard_io_resources)/sizeof(struct resource))
+
+static struct resource vram_resource = { "Video RAM area", 0xa0000, 0xbffff, IORESOURCE_BUSY };
+
+/* System ROM resources */
+#define MAXROMS 6
+static struct resource rom_resources[MAXROMS] = {
+ { "System ROM", 0xF0000, 0xFFFFF, IORESOURCE_BUSY },
+ { "Video ROM", 0xc0000, 0xc7fff, IORESOURCE_BUSY }
+};
+
+#define romsignature(x) (*(unsigned short *)(x) == 0xaa55)
+
+static inline void probe_roms(void)
+{
+ int roms = 1;
+ unsigned long base;
+ unsigned char *romstart;
+
+ request_resource(&iomem_resource, rom_resources+0);
+
+ /* Video ROM is standard at C000:0000 - C7FF:0000, check signature */
+ for (base = 0xC0000; base < 0xE0000; base += 2048) {
+ romstart = isa_bus_to_virt(base);
+ if (!romsignature(romstart))
+ continue;
+ request_resource(&iomem_resource, rom_resources + roms);
+ roms++;
+ break;
+ }
+
+ /* Extension roms at C800:0000 - DFFF:0000 */
+ for (base = 0xC8000; base < 0xE0000; base += 2048) {
+ unsigned long length;
+
+ romstart = isa_bus_to_virt(base);
+ if (!romsignature(romstart))
+ continue;
+ length = romstart[2] * 512;
+ if (length) {
+ unsigned int i;
+ unsigned char chksum;
+
+ chksum = 0;
+ for (i = 0; i < length; i++)
+ chksum += romstart[i];
+
+ /* Good checksum? */
+ if (!chksum) {
+ rom_resources[roms].start = base;
+ rom_resources[roms].end = base + length - 1;
+ rom_resources[roms].name = "Extension ROM";
+ rom_resources[roms].flags = IORESOURCE_BUSY;
+
+ request_resource(&iomem_resource, rom_resources + roms);
+ roms++;
+ if (roms >= MAXROMS)
+ return;
+ }
+ }
+ }
+
+ /* Final check for motherboard extension rom at E000:0000 */
+ base = 0xE0000;
+ romstart = isa_bus_to_virt(base);
+
+ if (romsignature(romstart)) {
+ rom_resources[roms].start = base;
+ rom_resources[roms].end = base + 65535;
+ rom_resources[roms].name = "Extension ROM";
+ rom_resources[roms].flags = IORESOURCE_BUSY;
+
+ request_resource(&iomem_resource, rom_resources + roms);
+ }
+}
+
+static inline void mach_request_resource(void)
+{
+ int i;
+
+ request_resource(&iomem_resource, &vram_resource);
+
+ /* request I/O space for devices used on all i[345]86 PCs */
+ for (i = 0; i < STANDARD_IO_RESOURCES; i++)
+ request_resource(&ioport_resource, standard_io_resources+i);
+
+}
+
+#endif /* !_MACH_RESOURCES_H */
diff -urN linux/arch/i386/mach-generic/mach_time.h linux98/arch/i386/mach-generic/mach_time.h
--- linux/arch/i386/mach-generic/mach_time.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-generic/mach_time.h Mon Oct 21 10:07:35 2002
@@ -0,0 +1,122 @@
+/*
+ * arch/i386/mach-generic/mach_time.h
+ *
+ * Machine specific set RTC function for generic.
+ * Split out from time.c by Osamu Tomita <tomita@cinet.co.jp>
+ */
+#ifndef _MACH_TIME_H
+#define _MACH_TIME_H
+
+#include <linux/mc146818rtc.h>
+
+/* for check timing call set_rtc_mmss() 500ms */
+/* used in arch/i386/time.c::do_timer_interrupt() */
+#define TIME1 500000
+#define TIME2 500000
+
+/*
+ * In order to set the CMOS clock precisely, set_rtc_mmss has to be
+ * called 500 ms after the second nowtime has started, because when
+ * nowtime is written into the registers of the CMOS clock, it will
+ * jump to the next second precisely 500 ms later. Check the Motorola
+ * MC146818A or Dallas DS12887 data sheet for details.
+ *
+ * BUG: This routine does not handle hour overflow properly; it just
+ * sets the minutes. Usually you'll only notice that after reboot!
+ */
+static inline int mach_set_rtc_mmss(unsigned long nowtime)
+{
+ int retval = 0;
+ int real_seconds, real_minutes, cmos_minutes;
+ unsigned char save_control, save_freq_select;
+
+ save_control = CMOS_READ(RTC_CONTROL); /* tell the clock it's being set */
+ CMOS_WRITE((save_control|RTC_SET), RTC_CONTROL);
+
+ save_freq_select = CMOS_READ(RTC_FREQ_SELECT); /* stop and reset prescaler */
+ CMOS_WRITE((save_freq_select|RTC_DIV_RESET2), RTC_FREQ_SELECT);
+
+ cmos_minutes = CMOS_READ(RTC_MINUTES);
+ if (!(save_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD)
+ BCD_TO_BIN(cmos_minutes);
+
+ /*
+ * since we're only adjusting minutes and seconds,
+ * don't interfere with hour overflow. This avoids
+ * messing with unknown time zones but requires your
+ * RTC not to be off by more than 15 minutes
+ */
+ real_seconds = nowtime % 60;
+ real_minutes = nowtime / 60;
+ if (((abs(real_minutes - cmos_minutes) + 15)/30) & 1)
+ real_minutes += 30; /* correct for half hour time zone */
+ real_minutes %= 60;
+
+ if (abs(real_minutes - cmos_minutes) < 30) {
+ if (!(save_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD) {
+ BIN_TO_BCD(real_seconds);
+ BIN_TO_BCD(real_minutes);
+ }
+ CMOS_WRITE(real_seconds,RTC_SECONDS);
+ CMOS_WRITE(real_minutes,RTC_MINUTES);
+ } else {
+ printk(KERN_WARNING
+ "set_rtc_mmss: can't update from %d to %d\n",
+ cmos_minutes, real_minutes);
+ retval = -1;
+ }
+
+ /* The following flags have to be released exactly in this order,
+ * otherwise the DS12887 (popular MC146818A clone with integrated
+ * battery and quartz) will not reset the oscillator and will not
+ * update precisely 500 ms later. You won't find this mentioned in
+ * the Dallas Semiconductor data sheets, but who believes data
+ * sheets anyway ... -- Markus Kuhn
+ */
+ CMOS_WRITE(save_control, RTC_CONTROL);
+ CMOS_WRITE(save_freq_select, RTC_FREQ_SELECT);
+
+ return retval;
+}
+
+static inline unsigned long mach_get_cmos_time(void)
+{
+ unsigned int year, mon, day, hour, min, sec;
+ int i;
+
+ /* The Linux interpretation of the CMOS clock register contents:
+ * When the Update-In-Progress (UIP) flag goes from 1 to 0, the
+ * RTC registers show the second which has precisely just started.
+ * Let's hope other operating systems interpret the RTC the same way.
+ */
+ /* read RTC exactly on falling edge of update flag */
+ for (i = 0 ; i < 1000000 ; i++) /* may take up to 1 second... */
+ if (CMOS_READ(RTC_FREQ_SELECT) & RTC_UIP)
+ break;
+ for (i = 0 ; i < 1000000 ; i++) /* must try at least 2.228 ms */
+ if (!(CMOS_READ(RTC_FREQ_SELECT) & RTC_UIP))
+ break;
+ do { /* Isn't this overkill ? UIP above should guarantee consistency */
+ sec = CMOS_READ(RTC_SECONDS);
+ min = CMOS_READ(RTC_MINUTES);
+ hour = CMOS_READ(RTC_HOURS);
+ day = CMOS_READ(RTC_DAY_OF_MONTH);
+ mon = CMOS_READ(RTC_MONTH);
+ year = CMOS_READ(RTC_YEAR);
+ } while (sec != CMOS_READ(RTC_SECONDS));
+ if (!(CMOS_READ(RTC_CONTROL) & RTC_DM_BINARY) || RTC_ALWAYS_BCD)
+ {
+ BCD_TO_BIN(sec);
+ BCD_TO_BIN(min);
+ BCD_TO_BIN(hour);
+ BCD_TO_BIN(day);
+ BCD_TO_BIN(mon);
+ BCD_TO_BIN(year);
+ }
+ if ((year += 1900) < 1970)
+ year += 100;
+
+ return mktime(year, mon, day, hour, min, sec);
+}
+
+#endif /* !_MACH_TIME_H */
diff -urN linux/arch/i386/mach-generic/mach_traps.h linux98/arch/i386/mach-generic/mach_traps.h
--- linux/arch/i386/mach-generic/mach_traps.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-generic/mach_traps.h Mon Oct 21 10:17:02 2002
@@ -0,0 +1,31 @@
+/*
+ * arch/i386/mach-generic/mach_traps.h
+ *
+ * Machine specific NMI handling for generic.
+ * Split out from traps.c by Osamu Tomita <tomita@cinet.co.jp>
+ */
+#ifndef _MACH_TRAPS_H
+#define _MACH_TRAPS_H
+
+#define HANDLE_REASON_0X40(reason, regs) io_check_error(reason, regs)
+
+static inline void clear_mem_error(unsigned char reason)
+{
+ reason = (reason & 0xf) | 4;
+ outb(reason, 0x61);
+}
+
+static inline unsigned char get_nmi_reason(void)
+{
+ return inb(0x61);
+}
+
+static inline void reassert_nmi(void)
+{
+ outb(0x8f, 0x70);
+ inb(0x71); /* dummy */
+ outb(0x0f, 0x70);
+ inb(0x71); /* dummy */
+}
+
+#endif /* !_MACH_TRAPS_H */
diff -urN linux/arch/i386/mach-pc9800/Makefile linux98/arch/i386/mach-pc9800/Makefile
--- linux/arch/i386/mach-pc9800/Makefile Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/Makefile Sat Sep 21 00:20:21 2002
@@ -0,0 +1,15 @@
+#
+# Makefile for the linux kernel.
+#
+# Note! Dependencies are done automagically by 'make dep', which also
+# removes any old dependencies. DON'T put your own dependencies here
+# unless it's something special (ie not a .c file).
+#
+# Note 2! The CFLAGS definitions are now in the main makefile...
+
+EXTRA_CFLAGS += -I../kernel
+export-objs := +
+obj-y := setup.o
+
+include $(TOPDIR)/Rules.make
diff -urN linux/arch/i386/mach-pc9800/calibrate_tsc.h linux98/arch/i386/mach-pc9800/calibrate_tsc.h
--- linux/arch/i386/mach-pc9800/calibrate_tsc.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/calibrate_tsc.h Mon Oct 21 11:01:05 2002
@@ -0,0 +1,73 @@
+/*
+ * arch/i386/mach-pc9800/calibrate_tsc.h
+ *
+ * Machine specific calibrate_tsc() for PC-9800.
+ * Written by Osamu Tomita <tomita@cinet.co.jp>
+ */
+
+/* ------ Calibrate the TSC ------- + * Return 2^32 * (1 / (TSC clocks per usec)) for do_fast_gettimeoffset().
+ * Too much 64-bit arithmetic here to do this cleanly in C.
+ * PC-9800:
+ * CTC cannot be used because some models (especially
+ * note-machines) may disable clock to speaker channel (#1)
+ * unless speaker is enabled. We use ARTIC instead.
+ */
+#ifndef _MACH_CALIBRATE_TSC_H
+#define _MACH_CALIBRATE_TSC_H
+
+#define CALIBRATE_LATCH (5 * 307200/HZ) /* 0.050sec * 307200Hz = 15360 */
+#define CALIBRATE_TIME (5 * 1000020/HZ)
+
+static unsigned long last_tsc_low; /* lsb 32 bits of Time Stamp Counter */
+
+static inline unsigned long calibrate_tsc(void)
+{
+
+ {
+ unsigned long startlow, starthigh;
+ unsigned long endlow, endhigh;
+ unsigned short count;
+
+ for (count = inw(0x5c); inw(0x5c) == count; )
+ ;
+ rdtsc(startlow,starthigh);
+ count = inw(0x5c);
+ while ((unsigned short)(inw(0x5c) - count) < CALIBRATE_LATCH)
+ ;
+ rdtsc(endlow,endhigh);
+
+ last_tsc_low = endlow;
+
+ /* 64-bit subtract - gcc just messes up with long longs */
+ __asm__("subl %2,%0\n\t"
+ "sbbl %3,%1"
+ :"=a" (endlow), "=d" (endhigh)
+ :"g" (startlow), "g" (starthigh),
+ "0" (endlow), "1" (endhigh));
+
+ /* Error: ECPUTOOFAST */
+ if (endhigh)
+ goto bad_ctc;
+
+ /* Error: ECPUTOOSLOW */
+ if (endlow <= CALIBRATE_TIME)
+ goto bad_ctc;
+
+ __asm__("divl %2"
+ :"=a" (endlow), "=d" (endhigh)
+ :"r" (endlow), "0" (0), "1" (CALIBRATE_TIME));
+
+ return endlow;
+ }
+
+ /*
+ * The CTC wasn't reliable: we got a hit on the very first read,
+ * or the CPU was so fast/slow that the quotient wouldn't fit in
+ * 32 bits..
+ */
+bad_ctc:
+ return 0;
+}
+
+#endif /* !_MACH_CALIBRATE_TSC_H */
diff -urN linux/arch/i386/mach-pc9800/do_timer.h linux98/arch/i386/mach-pc9800/do_timer.h
--- linux/arch/i386/mach-pc9800/do_timer.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/do_timer.h Wed Oct 16 13:20:29 2002
@@ -0,0 +1,80 @@
+/* defines for inline arch setup functions */
+
+/**
+ * do_timer_interrupt_hook - hook into timer tick
+ * @regs: standard registers from interrupt
+ *
+ * Description:
+ * This hook is called immediately after the timer interrupt is ack'd.
+ * It's primary purpose is to allow architectures that don't possess
+ * individual per CPU clocks (like the CPU APICs supply) to broadcast the
+ * timer interrupt as a means of triggering reschedules etc.
+ **/
+
+static inline void do_timer_interrupt_hook(struct pt_regs *regs)
+{
+ do_timer(regs);
+/*
+ * In the SMP case we use the local APIC timer interrupt to do the
+ * profiling, except when we simulate SMP mode on a uniprocessor
+ * system, in that case we have to call the local interrupt handler.
+ */
+#ifndef CONFIG_X86_LOCAL_APIC
+ x86_do_profile(regs);
+#else
+ if (!using_apic_timer)
+ smp_local_timer_interrupt(regs);
+#endif
+}
+
+
+/* you can safely undefine this if you don't have the Neptune chipset */
+
+#define BUGGY_NEPTUN_TIMER
+
+/**
+ * do_timer_overflow - process a detected timer overflow condition
+ * @count: hardware timer interrupt count on overflow
+ *
+ * Description:
+ * This call is invoked when the jiffies count has not incremented but
+ * the hardware timer interrupt has. It means that a timer tick interrupt
+ * came along while the previous one was pending, thus a tick was missed
+ **/
+static inline int do_timer_overflow(int count)
+{
+ int i;
+
+ spin_lock(&i8259A_lock);
+ /*
+ * This is tricky when I/O APICs are used;
+ * see do_timer_interrupt().
+ */
+ i = inb(0x00);
+ spin_unlock(&i8259A_lock);
+
+ /* assumption about timer being IRQ0 */
+ if (i & 0x01) {
+ /*
+ * We cannot detect lost timer interrupts ... + * well, that's why we call them lost, don't we? :)
+ * [hmm, on the Pentium and Alpha we can ... sort of]
+ */
+ count -= LATCH;
+ } else {
+#ifdef BUGGY_NEPTUN_TIMER
+ /*
+ * for the Neptun bug we know that the 'latch'
+ * command doesnt latch the high and low value
+ * of the counter atomically. Thus we have to + * substract 256 from the counter + * ... funny, isnt it? :)
+ */
+
+ count -= 256;
+#else
+ printk("do_slow_gettimeoffset(): hardware timer problem?\n");
+#endif
+ }
+ return count;
+}
diff -urN linux/arch/i386/mach-pc9800/entry_arch.h linux98/arch/i386/mach-pc9800/entry_arch.h
--- linux/arch/i386/mach-pc9800/entry_arch.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/entry_arch.h Sun Oct 20 17:42:49 2002
@@ -0,0 +1 @@
+#include "../mach-generic/entry_arch.h"
diff -urN linux/arch/i386/mach-pc9800/io_ports.h linux98/arch/i386/mach-pc9800/io_ports.h
--- linux/arch/i386/mach-pc9800/io_ports.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/io_ports.h Mon Oct 21 11:03:30 2002
@@ -0,0 +1,30 @@
+/*
+ * arch/i386/mach-pc9800/io_ports.h
+ *
+ * Machine specific IO port address definition for PC-9800.
+ * Written by Osamu Tomita <tomita@cinet.co.jp>
+ */
+#ifndef _MACH_IO_PORTS_H
+#define _MACH_IO_PORTS_H
+
+/* i8253A PIT registers */
+#define PIT_MODE 0x77
+#define PIT_CH0 0x71
+#define PIT_CH2 0x75
+
+/* i8259A PIC registers */
+#define PIC_MASTER_CMD 0x00
+#define PIC_MASTER_IMR 0x02
+#define PIC_MASTER_ISR PIC_MASTER_CMD
+#define PIC_MASTER_POLL PIC_MASTER_ISR
+#define PIC_MASTER_OCW3 PIC_MASTER_ISR
+#define PIC_SLAVE_CMD 0x08
+#define PIC_SLAVE_IMR 0x0a
+
+/* i8259A PIC related values */
+#define PIC_CASCADE_IR 7
+#define MASTER_ICW4_DEFAULT 0x1d
+#define SLAVE_ICW4_DEFAULT 0x09
+#define PIC_ICW4_AEOI 0x02
+
+#endif /* !_MACH_IO_PORTS_H */
diff -urN linux/arch/i386/mach-pc9800/irq_vectors.h linux98/arch/i386/mach-pc9800/irq_vectors.h
--- linux/arch/i386/mach-pc9800/irq_vectors.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/irq_vectors.h Sun Oct 20 17:45:10 2002
@@ -0,0 +1 @@
+#include "../mach-generic/irq_vectors.h"
diff -urN linux/arch/i386/mach-pc9800/mach_apic.h linux98/arch/i386/mach-pc9800/mach_apic.h
--- linux/arch/i386/mach-pc9800/mach_apic.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/mach_apic.h Sun Oct 20 17:46:53 2002
@@ -0,0 +1 @@
+#include "../mach-generic/mach_apic.h"
diff -urN linux/arch/i386/mach-pc9800/mach_reboot.h linux98/arch/i386/mach-pc9800/mach_reboot.h
--- linux/arch/i386/mach-pc9800/mach_reboot.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/mach_reboot.h Mon Oct 21 11:07:36 2002
@@ -0,0 +1,21 @@
+/*
+ * arch/i386/mach-pc9800/mach_reboot.h
+ *
+ * Machine specific reboot functions for PC-9800.
+ * Written by Osamu Tomita <tomita@cinet.co.jp>
+ */
+#ifndef _MACH_REBOOT_H
+#define _MACH_REBOOT_H
+
+#ifdef CMOS_WRITE
+#undef CMOS_WRITE
+#define CMOS_WRITE(a,b) do{}while(0)
+#endif
+
+static inline void mach_reboot(void)
+{
+ outb(0, 0xf0); /* signal CPU reset */
+ mdelay(1);
+}
+
+#endif /* !_MACH_REBOOT_H */
diff -urN linux/arch/i386/mach-pc9800/mach_resources.h linux98/arch/i386/mach-pc9800/mach_resources.h
--- linux/arch/i386/mach-pc9800/mach_resources.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/mach_resources.h Sat Oct 26 17:35:19 2002
@@ -0,0 +1,192 @@
+/*
+ * arch/i386/mach-pc9800/mach_resources.h
+ *
+ * Machine specific resource allocation for PC-9800.
+ * Written by Osamu Tomita <tomita@cinet.co.jp>
+ */
+#ifndef _MACH_RESOURCES_H
+#define _MACH_RESOURCES_H
+
+static char str_pic1[] = "pic1";
+static char str_dma[] = "dma";
+static char str_pic2[] = "pic2";
+static char str_calender_clock[] = "calender clock";
+static char str_system[] = "system";
+static char str_nmi_control[] = "nmi control";
+static char str_kanji_rom[] = "kanji rom";
+static char str_keyboard[] = "keyboard";
+static char str_text_gdc[] = "text gdc";
+static char str_crtc[] = "crtc";
+static char str_timer[] = "timer";
+static char str_graphic_gdc[] = "graphic gdc";
+static char str_dma_ex_bank[] = "dma ex. bank";
+static char str_beep_freq[] = "beep freq.";
+static char str_mouse_pio[] = "mouse pio";
+struct resource standard_io_resources[] = {
+ { str_pic1, 0x00, 0x00, IORESOURCE_BUSY },
+ { str_dma, 0x01, 0x01, IORESOURCE_BUSY },
+ { str_pic1, 0x02, 0x02, IORESOURCE_BUSY },
+ { str_dma, 0x03, 0x03, IORESOURCE_BUSY },
+ { str_dma, 0x05, 0x05, IORESOURCE_BUSY },
+ { str_dma, 0x07, 0x07, IORESOURCE_BUSY },
+ { str_pic2, 0x08, 0x08, IORESOURCE_BUSY },
+ { str_dma, 0x09, 0x09, IORESOURCE_BUSY },
+ { str_pic2, 0x0a, 0x0a, IORESOURCE_BUSY },
+ { str_dma, 0x0b, 0x0b, IORESOURCE_BUSY },
+ { str_dma, 0x0d, 0x0d, IORESOURCE_BUSY },
+ { str_dma, 0x0f, 0x0f, IORESOURCE_BUSY },
+ { str_dma, 0x11, 0x11, IORESOURCE_BUSY },
+ { str_dma, 0x13, 0x13, IORESOURCE_BUSY },
+ { str_dma, 0x15, 0x15, IORESOURCE_BUSY },
+ { str_dma, 0x17, 0x17, IORESOURCE_BUSY },
+ { str_dma, 0x19, 0x19, IORESOURCE_BUSY },
+ { str_dma, 0x1b, 0x1b, IORESOURCE_BUSY },
+ { str_dma, 0x1d, 0x1d, IORESOURCE_BUSY },
+ { str_dma, 0x1f, 0x1f, IORESOURCE_BUSY },
+ { str_calender_clock, 0x20, 0x20, 0 },
+ { str_dma, 0x21, 0x21, IORESOURCE_BUSY },
+ { str_calender_clock, 0x22, 0x22, 0 },
+ { str_dma, 0x23, 0x23, IORESOURCE_BUSY },
+ { str_dma, 0x25, 0x25, IORESOURCE_BUSY },
+ { str_dma, 0x27, 0x27, IORESOURCE_BUSY },
+ { str_dma, 0x29, 0x29, IORESOURCE_BUSY },
+ { str_dma, 0x2b, 0x2b, IORESOURCE_BUSY },
+ { str_dma, 0x2d, 0x2d, IORESOURCE_BUSY },
+ { str_system, 0x31, 0x31, IORESOURCE_BUSY },
+ { str_system, 0x33, 0x33, IORESOURCE_BUSY },
+ { str_system, 0x35, 0x35, IORESOURCE_BUSY },
+ { str_system, 0x37, 0x37, IORESOURCE_BUSY },
+ { str_nmi_control, 0x50, 0x50, IORESOURCE_BUSY },
+ { str_nmi_control, 0x52, 0x52, IORESOURCE_BUSY },
+ { "time stamp", 0x5c, 0x5f, IORESOURCE_BUSY },
+ { str_kanji_rom, 0xa1, 0xa1, IORESOURCE_BUSY },
+ { str_kanji_rom, 0xa3, 0xa3, IORESOURCE_BUSY },
+ { str_kanji_rom, 0xa5, 0xa5, IORESOURCE_BUSY },
+ { str_kanji_rom, 0xa7, 0xa7, IORESOURCE_BUSY },
+ { str_kanji_rom, 0xa9, 0xa9, IORESOURCE_BUSY },
+ { str_keyboard, 0x41, 0x41, IORESOURCE_BUSY },
+ { str_keyboard, 0x43, 0x43, IORESOURCE_BUSY },
+ { str_text_gdc, 0x60, 0x60, IORESOURCE_BUSY },
+ { str_text_gdc, 0x62, 0x62, IORESOURCE_BUSY },
+ { str_text_gdc, 0x64, 0x64, IORESOURCE_BUSY },
+ { str_text_gdc, 0x66, 0x66, IORESOURCE_BUSY },
+ { str_text_gdc, 0x68, 0x68, IORESOURCE_BUSY },
+ { str_text_gdc, 0x6a, 0x6a, IORESOURCE_BUSY },
+ { str_text_gdc, 0x6c, 0x6c, IORESOURCE_BUSY },
+ { str_text_gdc, 0x6e, 0x6e, IORESOURCE_BUSY },
+ { str_crtc, 0x70, 0x70, IORESOURCE_BUSY },
+ { str_crtc, 0x72, 0x72, IORESOURCE_BUSY },
+ { str_crtc, 0x74, 0x74, IORESOURCE_BUSY },
+ { str_crtc, 0x74, 0x74, IORESOURCE_BUSY },
+ { str_crtc, 0x76, 0x76, IORESOURCE_BUSY },
+ { str_crtc, 0x78, 0x78, IORESOURCE_BUSY },
+ { str_crtc, 0x7a, 0x7a, IORESOURCE_BUSY },
+ { str_timer, 0x71, 0x71, IORESOURCE_BUSY },
+ { str_timer, 0x73, 0x73, IORESOURCE_BUSY },
+ { str_timer, 0x75, 0x75, IORESOURCE_BUSY },
+ { str_timer, 0x77, 0x77, IORESOURCE_BUSY },
+ { str_graphic_gdc, 0xa0, 0xa0, IORESOURCE_BUSY },
+ { str_graphic_gdc, 0xa2, 0xa2, IORESOURCE_BUSY },
+ { str_graphic_gdc, 0xa4, 0xa4, IORESOURCE_BUSY },
+ { str_graphic_gdc, 0xa6, 0xa6, IORESOURCE_BUSY },
+ { "cpu", 0xf0, 0xf7, IORESOURCE_BUSY },
+ { "fpu", 0xf8, 0xff, IORESOURCE_BUSY },
+ { str_dma_ex_bank, 0x0e05, 0x0e05, 0 },
+ { str_dma_ex_bank, 0x0e07, 0x0e07, 0 },
+ { str_dma_ex_bank, 0x0e09, 0x0e09, 0 },
+ { str_dma_ex_bank, 0x0e0b, 0x0e0b, 0 },
+ { str_beep_freq, 0x3fd9, 0x3fd9, IORESOURCE_BUSY },
+ { str_beep_freq, 0x3fdb, 0x3fdb, IORESOURCE_BUSY },
+ { str_beep_freq, 0x3fdd, 0x3fdd, IORESOURCE_BUSY },
+ { str_beep_freq, 0x3fdf, 0x3fdf, IORESOURCE_BUSY },
+ /* All PC-9800 have (exactly) one mouse interface. */
+ { str_mouse_pio, 0x7fd9, 0x7fd9, 0 },
+ { str_mouse_pio, 0x7fdb, 0x7fdb, 0 },
+ { str_mouse_pio, 0x7fdd, 0x7fdd, 0 },
+ { str_mouse_pio, 0x7fdf, 0x7fdf, 0 },
+ { "mouse timer", 0xbfdb, 0xbfdb, 0 },
+ { "mouse irq", 0x98d7, 0x98d7, 0 },
+};
+
+#define STANDARD_IO_RESOURCES (sizeof(standard_io_resources)/sizeof(struct resource))
+
+static struct resource tvram_resource = { "Text VRAM/CG window", 0xa0000, 0xa4fff, IORESOURCE_BUSY };
+static struct resource gvram_brg_resource = { "Graphic VRAM (B/R/G)", 0xa8000, 0xbffff, IORESOURCE_BUSY };
+static struct resource gvram_e_resource = { "Graphic VRAM (E)", 0xe0000, 0xe7fff, IORESOURCE_BUSY };
+
+/* System ROM resources */
+#define MAXROMS 6
+static struct resource rom_resources[MAXROMS] = {
+ { "System ROM", 0xe8000, 0xfffff, IORESOURCE_BUSY }
+};
+
+static inline void probe_roms(void)
+{
+ int roms = 1;
+ int i;
+ __u8 *xrom_id;
+
+ request_resource(&iomem_resource, rom_resources+0);
+
+ xrom_id = (__u8 *) isa_bus_to_virt(PC9800SCA_XROM_ID + 0x10);
+
+ for (i = 0; i < 16; i++) {
+ if (xrom_id[i] & 0x80) {
+ int j;
+
+ for (j = i + 1; j < 16 && (xrom_id[j] & 0x80); j++)
+ ;
+ rom_resources[roms].start = 0x0d0000 + i * 0x001000;
+ rom_resources[roms].end = 0x0d0000 + j * 0x001000 - 1;
+ rom_resources[roms].name = "Extension ROM";
+ rom_resources[roms].flags = IORESOURCE_BUSY;
+
+ request_resource(&iomem_resource,
+ rom_resources + roms);
+ if (++roms >= MAXROMS)
+ return;
+ }
+ }
+}
+
+static inline void mach_request_resource(void)
+{
+ int i;
+
+ if (PC9800_HIGHRESO_P()) {
+ tvram_resource.start = 0xe0000;
+ tvram_resource.end = 0xe4fff;
+ gvram_brg_resource.name = "Graphic VRAM";
+ gvram_brg_resource.start = 0xc0000;
+ gvram_brg_resource.end = 0xdffff;
+ }
+
+ request_resource(&iomem_resource, &tvram_resource);
+ request_resource(&iomem_resource, &gvram_brg_resource);
+ if (!PC9800_HIGHRESO_P())
+ request_resource(&iomem_resource, &gvram_e_resource);
+
+ for (i = 0; i < STANDARD_IO_RESOURCES; i++)
+ request_resource(&ioport_resource, standard_io_resources + i);
+
+ if (PC9800_HIGHRESO_P() || PC9800_9821_P()) {
+ static char graphics[] = "graphics";
+ static struct resource graphics_resources[] = {
+ { graphics, 0x9a0, 0x9a0, 0 },
+ { graphics, 0x9a2, 0x9a2, 0 },
+ { graphics, 0x9a4, 0x9a4, 0 },
+ { graphics, 0x9a6, 0x9a6, 0 },
+ { graphics, 0x9a8, 0x9a8, 0 },
+ { graphics, 0x9aa, 0x9aa, 0 },
+ { graphics, 0x9ac, 0x9ac, 0 },
+ { graphics, 0x9ae, 0x9ae, 0 },
+ };
+
+#define GRAPHICS_RESOURCES (sizeof(graphics_resources)/sizeof(struct resource))
+
+ for (i = 0; i < GRAPHICS_RESOURCES; i++)
+ request_resource(&ioport_resource, graphics_resources + i);
+ }
+}
+
+#endif /* !_MACH_RESOURCES_H */
diff -urN linux/arch/i386/mach-pc9800/mach_time.h linux98/arch/i386/mach-pc9800/mach_time.h
--- linux/arch/i386/mach-pc9800/mach_time.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/mach_time.h Mon Oct 21 11:23:06 2002
@@ -0,0 +1,136 @@
+/*
+ * arch/i386/mach-pc9800/mach_time.h
+ *
+ * Machine specific set RTC function for PC-9800.
+ * Written by Osamu Tomita <tomita@cinet.co.jp>
+ */
+#ifndef _MACH_TIME_H
+#define _MACH_TIME_H
+
+#include <linux/upd4990a.h>
+
+/* for check timing call set_rtc_mmss() */
+/* used in arch/i386/time.c::do_timer_interrupt() */
+/*
+ * Because PC-9800's RTC (NEC uPD4990A) does not allow setting
+ * time partially, we always have to read-modify-write the
+ * entire time (including year) so that set_rtc_mmss() will
+ * take quite much time to execute. You may want to relax
+ * RTC resetting interval (currently ~11 minuts)...
+ */
+#define TIME1 1000000
+#define TIME2 0
+
+static inline int mach_set_rtc_mmss(unsigned long nowtime)
+{
+ int retval = 0;
+ int real_seconds, real_minutes, cmos_minutes;
+ struct upd4990a_raw_data data;
+
+ upd4990a_get_time(&data, 1);
+ cmos_minutes = (data.min >> 4) * 10 + (data.min & 0xf);
+
+ /*
+ * since we're only adjusting minutes and seconds,
+ * don't interfere with hour overflow. This avoids
+ * messing with unknown time zones but requires your
+ * RTC not to be off by more than 15 minutes
+ */
+ real_seconds = nowtime % 60;
+ real_minutes = nowtime / 60;
+ if (((abs(real_minutes - cmos_minutes) + 15) / 30) & 1)
+ real_minutes += 30; /* correct for half hour time zone */
+ real_minutes %= 60;
+
+ if (abs(real_minutes - cmos_minutes) < 30) {
+ u8 temp_seconds = (real_seconds / 10) * 16 + real_seconds % 10;
+ u8 temp_minutes = (real_minutes / 10) * 16 + real_minutes % 10;
+
+ if (data.sec != temp_seconds || data.min != temp_minutes) {
+ data.sec = temp_seconds;
+ data.min = temp_minutes;
+ upd4990a_set_time(&data, 1);
+ }
+ } else {
+ printk(KERN_WARNING
+ "set_rtc_mmss: can't update from %d to %d\n",
+ cmos_minutes, real_minutes);
+ retval = -1;
+ }
+
+ /* uPD4990A users' manual says we should issue Register Hold
+ * command after reading time, or future Time Read command
+ * may not work. When we have set the time, this also starts
+ * the clock.
+ */
+ upd4990a_serial_command(UPD4990A_REGISTER_HOLD);
+
+ return retval;
+}
+
+#define RTC_SANITY_CHECK
+
+static inline unsigned long mach_get_cmos_time(void)
+{
+ int i;
+ u8 prev, cur;
+ unsigned int year;
+#ifdef RTC_SANITY_CHECK
+ int retry_count;
+#endif
+
+ struct upd4990a_raw_data data;
+
+#ifdef RTC_SANITY_CHECK
+ retry_count = 0;
+ retry:
+#endif
+ /* Connect uPD4990A's DATA OUT pin to its 1Hz reference clock. */
+ upd4990a_serial_command(UPD4990A_REGISTER_HOLD);
+
+ /* Catch rising edge of reference clock. */
+ prev = ~UPD4990A_READ_DATA();
+ for (i = 0; i < 1800000; i++) { /* may take up to 1 second... */
+ __asm__ ("outb %%al,%0" : : "N" (0x5f)); /* 0.6usec delay */
+ cur = UPD4990A_READ_DATA();
+ if (!(prev & cur & 1))
+ break;
+ prev = ~cur;
+ }
+
+ upd4990a_get_time(&data, 0);
+
+#ifdef RTC_SANITY_CHECK
+# define BCD_VALID_P(x, hi) (((x) & 0x0f) <= 9 && (x) <= 0x ## hi)
+# define DATA ((const unsigned char *) &data)
+
+ if (!BCD_VALID_P(data.sec, 59) ||
+ !BCD_VALID_P(data.min, 59) ||
+ !BCD_VALID_P(data.hour, 23) ||
+ data.mday == 0 || !BCD_VALID_P(data.mday, 31) ||
+ data.wday > 6 ||
+ data.mon < 1 || 12 < data.mon ||
+ !BCD_VALID_P(data.year, 99)) {
+ printk(KERN_ERR "RTC clock data is invalid! "
+ "(%02X %02X %02X %02X %02X %02X) - ",
+ DATA[0], DATA[1], DATA[2], DATA[3], DATA[4], DATA[5]);
+ if (++retry_count < 3) {
+ printk("retrying (%d)\n", retry_count);
+ goto retry;
+ }
+ printk("giving up, continuing\n");
+ }
+
+# undef BCD_VALID_P
+# undef DATA
+#endif /* RTC_SANITY_CHECK */
+
+#define CVT(x) (((x) & 0xF) + ((x) >> 4) * 10)
+ if ((year = CVT(data.year) + 1900) < 1995)
+ year += 100;
+ return mktime(year, data.mon, CVT(data.mday),
+ CVT(data.hour), CVT(data.min), CVT(data.sec));
+#undef CVT
+}
+
+#endif /* !_MACH_TIME_H */
diff -urN linux/arch/i386/mach-pc9800/mach_traps.h linux98/arch/i386/mach-pc9800/mach_traps.h
--- linux/arch/i386/mach-pc9800/mach_traps.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/mach_traps.h Mon Oct 21 11:26:12 2002
@@ -0,0 +1,29 @@
+/*
+ * arch/i386/mach-pc9800/mach_traps.h
+ *
+ * Machine specific NMI handling for PC-9800.
+ * Written by Osamu Tomita <tomita@cinet.co.jp>
+ */
+#ifndef _MACH_TRAPS_H
+#define _MACH_TRAPS_H
+
+#define HANDLE_REASON_0X40(reason, regs) mem_parity_error(reason, regs)
+
+static inline void clear_mem_error(unsigned char reason)
+{
+ outb(0x08, 0x37);
+ outb(0x09, 0x37);
+}
+
+static inline unsigned char get_nmi_reason(void)
+{
+ return inb(0x33) << 5;
+}
+
+static inline void reassert_nmi(void)
+{
+ outb(0x09, 0x50); /* disable NMI once */
+ outb(0x09, 0x52); /* re-enable it */
+}
+
+#endif /* !_MACH_TRAPS_H */
diff -urN linux/arch/i386/mach-pc9800/setup.c linux98/arch/i386/mach-pc9800/setup.c
--- linux/arch/i386/mach-pc9800/setup.c Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/setup.c Sat Oct 26 17:08:45 2002
@@ -0,0 +1,117 @@
+/*
+ * Machine specific setup for generic
+ */
+
+#include <linux/config.h>
+#include <linux/mm.h>
+#include <linux/smp.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <asm/setup.h>
+#include <asm/arch_hooks.h>
+
+struct sys_desc_table_struct {
+ unsigned short length;
+ unsigned char table[0];
+};
+
+/* Indicates PC-9800 architecture No:0 Yes:1 */
+extern int pc98;
+
+/**
+ * pre_intr_init_hook - initialisation prior to setting up interrupt vectors
+ *
+ * Description:
+ * Perform any necessary interrupt initialisation prior to setting up
+ * the "ordinary" interrupt call gates. For legacy reasons, the ISA
+ * interrupts should be initialised here if the machine emulates a PC
+ * in any way.
+ **/
+void __init pre_intr_init_hook(void)
+{
+ init_ISA_irqs();
+}
+
+/*
+ * IRQ7 is cascade interrupt to second interrupt controller
+ */
+static struct irqaction irq7 = { no_action, 0, 0, "cascade", NULL, NULL};
+
+/**
+ * intr_init_hook - post gate setup interrupt initialisation
+ *
+ * Description:
+ * Fill in any interrupts that may have been left out by the general
+ * init_IRQ() routine. interrupts having to do with the machine rather
+ * than the devices on the I/O bus (like APIC interrupts in intel MP
+ * systems) are started here.
+ **/
+void __init intr_init_hook(void)
+{
+#ifdef CONFIG_X86_LOCAL_APIC
+ apic_intr_init();
+#endif
+
+ setup_irq(7, &irq7);
+}
+
+/**
+ * pre_setup_arch_hook - hook called prior to any setup_arch() execution
+ *
+ * Description:
+ * generally used to activate any machine specific identification
+ * routines that may be needed before setup_arch() runs. On VISWS
+ * this is used to get the board revision and type.
+ **/
+void __init pre_setup_arch_hook(void)
+{
+ SYS_DESC_TABLE.length = 0;
+ MCA_bus = 0;
+ pc98 = 1;
+}
+
+/**
+ * trap_init_hook - initialise system specific traps
+ *
+ * Description:
+ * Called as the final act of trap_init(). Used in VISWS to initialise
+ * the various board specific APIC traps.
+ **/
+void __init trap_init_hook(void)
+{
+}
+
+static struct irqaction irq0 = { timer_interrupt, SA_INTERRUPT, 0, "timer", NULL, NULL};
+
+/**
+ * time_init_hook - do any specific initialisations for the system timer.
+ *
+ * Description:
+ * Must plug the system timer interrupt source at HZ into the IRQ listed
+ * in irq_vectors.h:TIMER_IRQ
+ **/
+void __init time_init_hook(void)
+{
+ setup_irq(0, &irq0);
+}
+
+#ifdef CONFIG_MCA
+/**
+ * mca_nmi_hook - hook into MCA specific NMI chain
+ *
+ * Description:
+ * The MCA (Microchannel Arcitecture) has an NMI chain for NMI sources
+ * along the MCA bus. Use this to hook into that chain if you will need
+ * it.
+ **/
+void __init mca_nmi_hook(void)
+{
+ /* If I recall correctly, there's a whole bunch of other things that
+ * we can do to check for NMI problems, but that's all I know about
+ * at the moment.
+ */
+
+ printk("NMI generated from unknown source!\n");
+}
+#endif
diff -urN linux/arch/i386/mach-pc9800/setup_arch_post.h linux98/arch/i386/mach-pc9800/setup_arch_post.h
--- linux/arch/i386/mach-pc9800/setup_arch_post.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/setup_arch_post.h Sat Sep 21 23:00:26 2002
@@ -0,0 +1,29 @@
+/**
+ * machine_specific_memory_setup - Hook for machine specific memory setup.
+ *
+ * Description:
+ * This is included late in kernel/setup.c so that it can make
+ * use of all of the static functions.
+ **/
+
+static inline char * __init machine_specific_memory_setup(void)
+{
+ char *who;
+ unsigned long low_mem_size, lower_high, higher_high;
+
+
+ who = "BIOS (common area)";
+
+ low_mem_size = ((*(unsigned char *)__va(PC9800SCA_BIOS_FLAG) & 7) + 1) << 17;
+ add_memory_region(0, low_mem_size, 1);
+ lower_high = (__u32) *(__u8 *) bus_to_virt(PC9800SCA_EXPMMSZ) << 17;
+ higher_high = (__u32) *(__u16 *) bus_to_virt(PC9800SCA_MMSZ16M) << 20;
+ if (lower_high != 0x00f00000UL) {
+ add_memory_region(HIGH_MEMORY, lower_high, 1);
+ add_memory_region(0x01000000UL, higher_high, 1);
+ }
+ else
+ add_memory_region(HIGH_MEMORY, lower_high + higher_high, 1);
+
+ return who;
+}
diff -urN linux/arch/i386/mach-pc9800/setup_arch_pre.h linux98/arch/i386/mach-pc9800/setup_arch_pre.h
--- linux/arch/i386/mach-pc9800/setup_arch_pre.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/setup_arch_pre.h Sun Sep 22 07:58:29 2002
@@ -0,0 +1,36 @@
+/* Hook to call BIOS initialisation function */
+
+/* no action for generic */
+
+#define ARCH_SETUP arch_setup_pc9800();
+
+#include <linux/timex.h>
+#include <asm/io.h>
+#include <asm/pc9800.h>
+#include <asm/pc9800_sca.h>
+
+int CLOCK_TICK_RATE;
+unsigned long tick_usec; /* ACTHZ period (usec) */
+unsigned long tick_nsec; /* USER_HZ period (nsec) */
+unsigned char pc9800_misc_flags;
+/* (bit 0) 1:High Address Video ram exists 0:otherwise */
+
+#ifdef CONFIG_SMP
+#define MPC_TABLE_SIZE 512
+#define MPC_TABLE ((char *) (PARAM+0x400))
+char mpc_table[MPC_TABLE_SIZE];
+#endif
+
+static inline void arch_setup_pc9800(void)
+{
+ CLOCK_TICK_RATE = PC9800_8MHz_P() ? 1996800 : 2457600;
+ printk(KERN_DEBUG "CLOCK_TICK_RATE = %d\n", CLOCK_TICK_RATE);
+ tick_usec = TICK_USEC; /* ACTHZ period (usec) */
+ tick_nsec = TICK_NSEC(TICK_USEC); /* USER_HZ period (nsec) */
+
+ pc9800_misc_flags = PC9800_MISC_FLAGS;
+#ifdef CONFIG_SMP
+ if ((*(u32 *)(MPC_TABLE)) == 0x504d4350)
+ memcpy(mpc_table, MPC_TABLE, *(u16 *)(MPC_TABLE + 4));
+#endif /* CONFIG_SMP */
+}
diff -urN linux/arch/i386/mach-pc9800/smpboot_hooks.h linux98/arch/i386/mach-pc9800/smpboot_hooks.h
--- linux/arch/i386/mach-pc9800/smpboot_hooks.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-pc9800/smpboot_hooks.h Sun Sep 22 06:56:46 2002
@@ -0,0 +1,33 @@
+/* two abstractions specific to kernel/smpboot.c, mainly to cater to visws
+ * which needs to alter them. */
+
+static inline void smpboot_clear_io_apic_irqs(void)
+{
+ io_apic_irqs = 0;
+}
+
+static inline void smpboot_setup_warm_reset_vector(void)
+{
+ /*
+ * Install writable page 0 entry to set BIOS data area.
+ */
+ local_flush_tlb();
+
+ /*
+ * Paranoid: Set warm reset code and vector here back
+ * to default values.
+ */
+ outb(0x0f, 0x37); /* SHUT0 = 1 */
+
+ *((volatile long *) phys_to_virt(0x404)) = 0;
+}
+
+static inline void smpboot_setup_io_apic(void)
+{
+ /*
+ * Here we can be sure that there is an IO-APIC in the system. Let's
+ * go and set it up:
+ */
+ if (!skip_ioapic_setup && nr_ioapics)
+ setup_IO_APIC();
+}
diff -urN linux/arch/i386/mach-summit/calibrate_tsc.h linux98/arch/i386/mach-summit/calibrate_tsc.h
--- linux/arch/i386/mach-summit/calibrate_tsc.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-summit/calibrate_tsc.h Mon Oct 21 02:46:34 2002
@@ -0,0 +1 @@
+#include "../mach-generic/calibrate_tsc.h"
diff -urN linux/arch/i386/mach-summit/io_ports.h linux98/arch/i386/mach-summit/io_ports.h
--- linux/arch/i386/mach-summit/io_ports.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-summit/io_ports.h Sun Oct 20 18:08:54 2002
@@ -0,0 +1 @@
+#include "../mach-generic/io_ports.h"
diff -urN linux/arch/i386/mach-summit/mach_reboot.h linux98/arch/i386/mach-summit/mach_reboot.h
--- linux/arch/i386/mach-summit/mach_reboot.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-summit/mach_reboot.h Sun Oct 20 18:10:25 2002
@@ -0,0 +1 @@
+#include "../mach-generic/mach_reboot.h"
diff -urN linux/arch/i386/mach-summit/mach_resources.h linux98/arch/i386/mach-summit/mach_resources.h
--- linux/arch/i386/mach-summit/mach_resources.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-summit/mach_resources.h Sun Oct 20 18:11:27 2002
@@ -0,0 +1 @@
+#include "../mach-generic/mach_resources.h"
diff -urN linux/arch/i386/mach-summit/mach_time.h linux98/arch/i386/mach-summit/mach_time.h
--- linux/arch/i386/mach-summit/mach_time.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-summit/mach_time.h Sun Oct 20 20:00:44 2002
@@ -0,0 +1 @@
+#include "../mach-generic/mach_time.h"
diff -urN linux/arch/i386/mach-summit/mach_traps.h linux98/arch/i386/mach-summit/mach_traps.h
--- linux/arch/i386/mach-summit/mach_traps.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-summit/mach_traps.h Mon Oct 21 02:48:48 2002
@@ -0,0 +1 @@
+#include "../mach-generic/mach_traps.h"
diff -urN linux/arch/i386/mach-visws/calibrate_tsc.h linux98/arch/i386/mach-visws/calibrate_tsc.h
--- linux/arch/i386/mach-visws/calibrate_tsc.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-visws/calibrate_tsc.h Mon Oct 21 02:46:34 2002
@@ -0,0 +1 @@
+#include "../mach-generic/calibrate_tsc.h"
diff -urN linux/arch/i386/mach-visws/io_ports.h linux98/arch/i386/mach-visws/io_ports.h
--- linux/arch/i386/mach-visws/io_ports.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-visws/io_ports.h Sun Oct 20 18:08:54 2002
@@ -0,0 +1 @@
+#include "../mach-generic/io_ports.h"
diff -urN linux/arch/i386/mach-visws/mach_reboot.h linux98/arch/i386/mach-visws/mach_reboot.h
--- linux/arch/i386/mach-visws/mach_reboot.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-visws/mach_reboot.h Sun Oct 20 18:10:25 2002
@@ -0,0 +1 @@
+#include "../mach-generic/mach_reboot.h"
diff -urN linux/arch/i386/mach-visws/mach_resources.h linux98/arch/i386/mach-visws/mach_resources.h
--- linux/arch/i386/mach-visws/mach_resources.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-visws/mach_resources.h Sun Oct 20 18:11:27 2002
@@ -0,0 +1 @@
+#include "../mach-generic/mach_resources.h"
diff -urN linux/arch/i386/mach-visws/mach_time.h linux98/arch/i386/mach-visws/mach_time.h
--- linux/arch/i386/mach-visws/mach_time.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-visws/mach_time.h Sun Oct 20 20:00:44 2002
@@ -0,0 +1 @@
+#include "../mach-generic/mach_time.h"
diff -urN linux/arch/i386/mach-visws/mach_traps.h linux98/arch/i386/mach-visws/mach_traps.h
--- linux/arch/i386/mach-visws/mach_traps.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-visws/mach_traps.h Mon Oct 21 02:48:48 2002
@@ -0,0 +1 @@
+#include "../mach-generic/mach_traps.h"
diff -urN linux/arch/i386/mach-voyager/calibrate_tsc.h linux98/arch/i386/mach-voyager/calibrate_tsc.h
--- linux/arch/i386/mach-voyager/calibrate_tsc.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-voyager/calibrate_tsc.h Mon Oct 21 02:46:34 2002
@@ -0,0 +1 @@
+#include "../mach-generic/calibrate_tsc.h"
diff -urN linux/arch/i386/mach-voyager/io_ports.h linux98/arch/i386/mach-voyager/io_ports.h
--- linux/arch/i386/mach-voyager/io_ports.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-voyager/io_ports.h Sun Oct 20 18:08:54 2002
@@ -0,0 +1 @@
+#include "../mach-generic/io_ports.h"
diff -urN linux/arch/i386/mach-voyager/mach_reboot.h linux98/arch/i386/mach-voyager/mach_reboot.h
--- linux/arch/i386/mach-voyager/mach_reboot.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-voyager/mach_reboot.h Sun Oct 20 18:10:25 2002
@@ -0,0 +1 @@
+#include "../mach-generic/mach_reboot.h"
diff -urN linux/arch/i386/mach-voyager/mach_resources.h linux98/arch/i386/mach-voyager/mach_resources.h
--- linux/arch/i386/mach-voyager/mach_resources.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-voyager/mach_resources.h Sun Oct 20 18:11:27 2002
@@ -0,0 +1 @@
+#include "../mach-generic/mach_resources.h"
diff -urN linux/arch/i386/mach-voyager/mach_time.h linux98/arch/i386/mach-voyager/mach_time.h
--- linux/arch/i386/mach-voyager/mach_time.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-voyager/mach_time.h Sun Oct 20 20:00:44 2002
@@ -0,0 +1 @@
+#include "../mach-generic/mach_time.h"
diff -urN linux/arch/i386/mach-voyager/mach_traps.h linux98/arch/i386/mach-voyager/mach_traps.h
--- linux/arch/i386/mach-voyager/mach_traps.h Thu Jan 1 09:00:00 1970
+++ linux98/arch/i386/mach-voyager/mach_traps.h Mon Oct 21 02:48:48 2002
@@ -0,0 +1 @@
+#include "../mach-generic/mach_traps.h"
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Osamu Tomita: "[RFC][Patchset 5/20] Support for PC-9800 (core2)"
Previous message: Osamu Tomita: "[RFC][Patchset 3/20] Support for PC-9800 (console)"