Hello,
kernel: linux-2.5.44
hardware:DELL Inspiron 8100
mouse: Logitech USB Optical Mouse
config:
CONFIG_INPUT_MOUSEDEV
CONFIG_INPUT_EVDEV
CONFIG_SERIO
CONFIG_SERIO_I8042
CONFIG_INPUT_MOUSE
CONFIG_MOUSE_PS2
CONFIG_USB
CONFIG_USB_HID
CONFIG_USB_HIDINPUT
dmesg output:
drivers/usb/core/hub.c: new USB device 00:1f.2-1, assigned address 2
drivers/usb/input/hid-ff.c: hid_ff_init could not find initializer
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-00:1f.2-1
--- snip ---
drivers/usb/host/uhci-hcd.c: bce0: host controller halted. very bad
drivers/usb/core/usb.c: USB disconnect on device 2
drivers/usb/core/hub.c: new USB device 00:1f.2-1, assigned address 3
drivers/usb/core/hub.c: new USB device 00:1f.2-1, assigned address 4
drivers/usb/core/hub.c: new USB device 00:1f.2-2, assigned address 5
drivers/usb/input/hid-ff.c: hid_ff_init could not find initializer
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-00:1f.2-2
drivers/usb/core/usb.c: USB disconnect on device 5
drivers/usb/core/hub.c: new USB device 00:1f.2-2, assigned address 6
drivers/usb/core/hub.c: new USB device 00:1f.2-2, assigned address 7
drivers/usb/core/hub.c: new USB device 00:1f.2-1, assigned address 8
drivers/usb/core/hub.c: new USB device 00:1f.2-1, assigned address 9
Events:
The USB mouse is connected to port 1
After boot the mouse works
I remove the USB mouse, then re-insert it in port 1
The mouse turns on the LED 3 times, then off, the mouse does not work.
I remove the USB mouse, then re-insert it in port 1
The mouse turns on the LED 3 times, then off, the mouse does not work.
I remove the USB mouse, the insert it in port 2
The mouse works
I remove the USB mouse, then re-insert it in port 2
The mouse turns on the LED 3 times, then off, the mouse does not work.
I remove the USB mouse, then re-insert it in port 2
The mouse turns on the LED 3 times, then off, the mouse does not work.
I remove the USB mouse from port 2, then re-insert it in port 1
The mouse turns on the LED 3 times, then off, the mouse does not work.
I remove the USB mouse, then re-insert it in port 1
The mouse turns on the LED 3 times, then off, the mouse does not work.
Thanks,
Take
- --
Take Vos <Take.Vos@binary-magic.com>
GnuPG: 2A5C110609995A378302A27630C962CCFD54AA85
http://binary-magic.com/~takev/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.0.7 (GNU/Linux)
iD8DBQE9tlbeMMlizP1UqoURAlxWAKDHK22AVYlmgBAXZbxbkuO7MuChYQCdGkWE
M3lpxFwv3lh9TJ/EDG4yJvQ=
=yNds
-----END PGP SIGNATURE-----
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/