[BUG] 2.5.30 ide problems booting

[Ed Tomlinson]

Hi,

I get the following booting 2.5.30:

Linux version 2.5.30 (ed@oscar) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 Thu Aug 1 21:16:02 EDT 2002
Video mode to be used for restore is f00
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
 BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
 BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=Linux25 ro root=2103 console=tty0 console=ttyS0,38400 video=matrox:mem:32 idebus=33
idebus=33
Initializing CPU#0
Detected 400.879 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 790.52 BogoMIPS
Memory: 516836k/524224k available (1076k kernel code, 7004k reserved, 324k data, 208k init, 0k highmem)
Security Scaffold v1.0.0 initialized
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Enabling new style K6 write allocation for 511 Mb
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: L2 Cache: 256K (32 bytes/line)
CPU: AMD-K6(tm) 3D+ Processor stepping 01
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([e-mail])
mtrr: detected mtrr type: AMD K6
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
PCI: PCI BIOS revision 2.10 entry at 0xfb520, last bus=1
PCI: Using configuration type 1
usb.c: registered new driver usbfs
usb.c: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0586] at 00:07.0
Starting kswapd
BIO: pool of 256 setup, 14Kb (56 bytes/bio)
biovec: init pool 0, 1 entries, 12 bytes
biovec: init pool 1, 4 entries, 48 bytes
biovec: init pool 2, 16 entries, 192 bytes
biovec: init pool 3, 64 entries, 768 bytes
biovec: init pool 4, 128 entries, 1536 bytes
biovec: init pool 5, 256 entries, 3072 bytes
Capability LSM initialized
Activating ISA DMA hang workarounds.
Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
matroxfb: Matrox Millennium G400 MAX (AGP) detected
matroxfb: MTRR's turned on
matroxfb: 640x480x8bpp (virtual: 640x26208)
matroxfb: framebuffer at 0xE8000000, mapped to 0xe0805000, size 33554432
Console: switching to colour frame buffer device 80x30
fb0: MATROX VGA frame buffer device
pty: 256 Unix98 ptys configured
block: 256 slots per queue, batch=32
ATA/ATAPI device driver v7.0.0
ATA: PCI bus speed 33.3MHz
ATA: VIA Technologies, Inc. Bus Master IDE, PCI slot 00:07.1
ATA: chipset rev.: 6
ATA: non-legacy mode: IRQ probe delayed
VP_IDE: VIA vt82c586b (rev 47) ATA UDMA33 controller on PCI 00:07.1
    ide0: BM-DMA at 0xa000-0xa007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xa008-0xa00f, BIOS settings: hdc:DMA, hdd:DMA
ATA: Promise Technology, Inc. 20267, PCI slot 00:09.0
PCI: Found IRQ 12 for device 00:09.0
ATA: chipset rev.: 2
ATA: non-legacy mode: IRQ probe delayed
Promise Technology, Inc. 20267: ROM enabled at 0xeb000000
Promise Technology, Inc. 20267: (U)DMA BURST enabled, primary PCI mode, secondary PCI mode.
    ide2: BM-DMA at 0xbc00-0xbc07, BIOS settings: hde:DMA, hdf:pio
    ide3: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdg:DMA, hdh:DMA
hda: QUANTUM FIREBALLP KA13.6, DISK drive
hdc: CD-ROM 50X, ATAPI CD/DVD-ROM drive
hdd: HP COLORADO 20GB, ATAPI TAPE drive
hde: QUANTUM FIREBALLP AS40.0, DISK drive
hdg: QUANTUM FIREBALLP AS40.0, DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xac00-0xac07,0xb002 on irq 12
ide3 at 0xb400-0xb407,0xb802 on irq 12
 hda: 27067824 sectors w/371KiB Cache, CHS=26853/16/63, UDMA(33)
 hda: hda1 hda2 hda3 hda4 < hda5 >
 hde: 78177792 sectors w/1902KiB Cache, CHS=77557/16/63, UDMA(100)
 hde: hde1 hde2 hde3 hde4 < hde5 >
 hdg: 78177792 sectors w/1902KiB Cache, CHS=77557/16/63, UDMA(100)
 hdg: hdg1 hdg2 hdg3 hdg4 < hdg5 >
uhci-hcd.c: USB Universal Host Controller Interface driver v2.0
hcd-pci.c: uhci-hcd @ 00:07.2, VIA Technologies, Inc. UHCI USB
hcd-pci.c: irq 10, io base 0000a400
hcd.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found at /
hub.c: 2 ports detected
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device ide2(33,3), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (ide2(33,3)) for (ide2(33,3))
hde: dma_intr: bad DMA status (dma_stat=36)
hde: ide_dma_intr: status=0x50 [ drive ready,seek complete] 
hde: request error, nr. 1

The system did work compile from the bk tree before ide 110/111 were added.

Ed Tomlinson