I'm running 2.4.19-rc2-aa1 on an AMD K6-II 450 (bluemoon).
The CPU is family 5, model 8, stepping 12. It's constantly at no more
than fifty degree Fahrenheit, so it's certainly not a temperature bugset.
The problems are:
1. When booting, I always have to specify hde=none hdf=none ... hdl=none,
because otherwise IDE will start probing wildly. (never had that before)
2. Mouse and keyboard are both on one port. Now if I load gpm, the whole
PS/2 controller gets stuck until I unplug both mouse and keyboard and then
re-plug them. It all worked fine ever before.
bluemoon:/proc/pci
PCI devices found:
Bus 0, device 0, function 0:
Host bridge: Acer Laboratories Inc. [ALi] M1541 (rev 4).
Master Capable. Latency=64.
Non-prefetchable 32 bit memory at 0xd0000000 [0xdfffffff].
Bus 0, device 1, function 0:
PCI bridge: Acer Laboratories Inc. [ALi] M1541 PCI to AGP Controller (rev 4).
Master Capable. Latency=64. Min Gnt=8.
Bus 0, device 2, function 0:
USB Controller: Acer Laboratories Inc. [ALi] USB 1.1 Controller (rev 3).
IRQ 9.
Master Capable. Latency=64. Max Lat=80.
Non-prefetchable 32 bit memory at 0xce800000 [0xce800fff].
Bus 0, device 3, function 0:
Bridge: Acer Laboratories Inc. [ALi] M7101 PMU (rev 0).
Bus 0, device 6, function 0:
Multimedia audio controller: ESS Technology ES1969 Solo-1 Audiodrive (rev 1).
IRQ 5.
Master Capable. Latency=32. Min Gnt=2.Max Lat=24.
I/O at 0xd800 [0xd83f].
I/O at 0xd400 [0xd40f].
I/O at 0xd000 [0xd00f].
I/O at 0xb800 [0xb803].
I/O at 0xb400 [0xb403].
Bus 0, device 7, function 0:
ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge [Aladdin IV] (rev 195).
Bus 0, device 9, function 0:
SCSI storage controller: Advanced Micro Devices [AMD] 53c974 [PCscsi] (rev 16).
IRQ 9.
Master Capable. Latency=32. Min Gnt=4.Max Lat=40.
I/O at 0xb000 [0xb07f].
Bus 0, device 10, function 0:
Ethernet controller: 3Com Corporation 3cSOHO100-TX Hurricane (rev 48).
IRQ 5.
Master Capable. Latency=32. Min Gnt=10.Max Lat=10.
I/O at 0xa800 [0xa87f].
Non-prefetchable 32 bit memory at 0xce000000 [0xce00007f].
Bus 0, device 11, function 0:
Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 4).
IRQ 10.
Master Capable. Latency=32. Min Gnt=2.Max Lat=20.
I/O at 0xa400 [0xa41f].
Bus 0, device 11, function 1:
Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 1).
Master Capable. Latency=32.
I/O at 0xa000 [0xa007].
Bus 0, device 13, function 0:
Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS) (rev 0).
IRQ 9.
I/O at 0x9800 [0x981f].
Bus 0, device 15, function 0:
IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev 193).
Master Capable. Latency=32. Min Gnt=2.Max Lat=4.
I/O at 0x9400 [0x940f].
Bus 1, device 0, function 0:
VGA compatible controller: nVidia Corporation Vanta [NV6] (rev 21).
IRQ 11.
Master Capable. Latency=64. Min Gnt=5.Max Lat=1.
Non-prefetchable 32 bit memory at 0xcf000000 [0xcfffffff].
Prefetchable 32 bit memory at 0xe6000000 [0xe7ffffff].
bluemoon:/proc/ide/ali:
Ali M15x3 Chipset.
------------------
PCI Clock: 33.
CD_ROM FIFO:No , CD_ROM DMA:Yes
FIFO Status: contains 0 Words, runs.
-------------------primary channel-------------------secondary channel---------
channel status: Off Off
both channels togth: Yes Yes
Channel state: OK OK
Add. Setup Timing: 1T 1T
Command Act. Count: 8T 8T
Command Rec. Count: 16T 16T
----------------drive0-----------drive1------------drive0-----------drive1------
DMA enabled: Yes Yes Yes Yes
FIFO threshold: 8 Words 8 Words 4 Words 4 Words
FIFO mode: FIFO On FIFO On FIFO Off FIFO Off
Dt RW act. Cnt 3T 3T 3T 4T
Dt RW rec. Cnt 1T 1T 1T 3T
-----------------------------------UDMA Timings--------------------------------
UDMA: OK OK No No
UDMA timings: 2.5T 2.5T 1.5T 1.5T
Regards,
Thunder
-- (Use http://www.ebb.org/ungeek if you can't decode) ------BEGIN GEEK CODE BLOCK------ Version: 3.12 GCS/E/G/S/AT d- s++:-- a? C++$ ULAVHI++++$ P++$ L++++(+++++)$ E W-$ N--- o? K? w-- O- M V$ PS+ PE- Y- PGP+ t+ 5+ X+ R- !tv b++ DI? !D G e++++ h* r--- y- ------END GEEK CODE BLOCK------- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/