I'm curious about your configuration; on my system, I don't have to run
setserial at all, as the serial driver detects the modem automatically
on boot. Perhaps this is the problem--your attempt at manual
configuration is breaking what the kernel has already done?
Does your kernel detect any serial ports on boot? try "dmesg | grep ttyS"
or "grep ttyS /var/log/dmesg" Tell me how that goes.
On Thu, Jul 18, 2002 at 09:26:27AM -0700, linux@davidtrott.com wrote:
> [1.] One line summary of the problem:
> Unable to use "Actiontec 56K Internal PCI Call Waiting modem" with linux
> 2.4.19-rc2 kernel
>
> [2.] Full description of the problem/report:
>
> When I issue the following command to setup my serial port I get the error:
>
> root@delta:~# setserial /dev/ttyS2 uart 16550A port 0x9000 irq 5
> Cannot set serial info: Address already in use
>
> However I think that this error is spurious as I have ensured that the card
> is not sharing an IRQ with any other devices.
>
> Additionally I have built older kernels with the same config file and my
> modem works with the 2.4.6 kernel and does not work with the 2.4.7 kernel.
>
> When setserial fails, if I try to use minicom I get no response from the
> modem when I type in AT commands. If I use a working kernel the AT commands
> act normally.
>
> As a test I copied the following files from the 2.4.6 source tree into my
> 2.4.19-rc2 tree:
>
> /usr/src/linux/drivers/char/serial.c
> /usr/src/linux/include/linux/serial.h
> /usr/src/linux/include/linux/serialP.h
>
> With this "patch" applied I can use my modem with no issues.
>
>
> [3.] Keywords (i.e., modules, networking, kernel):
> serial.c, actiontec, Modem
>
> [4.] Kernel version (from /proc/version):
> Linux version 2.4.19-rc2 (root@delta) (gcc version 2.95.3 20010315
> (release)) #1 Wed Jul 17 21:37:46 PDT 2002
>
>
> [5.] Output of Oops.. message (if applicable) with symbolic information resolved
> N/A
>
> [6.] A small shell script or example program which triggers the
> problem (if possible)
> See description
>
> [7.] Environment
> The follow is a non working environment from the vanilla rc2
>
> [7.1.] Software (add the output of the ver_linux script here)
>
> Linux delta 2.4.19-rc2 #1 Wed Jul 17 21:37:46 PDT 2002 i686 unknown
>
> Gnu C 2.95.3
> Gnu make 3.79.1
> binutils 2.11.90.0.19
> util-linux 2.11f
> mount 2.11b
> modutils 2.4.6
> e2fsprogs 1.27
> reiserfsprogs 3.x.0j
> pcmcia-cs 3.1.26
> PPP 2.4.1
> Linux C Library 2.2.3
> Dynamic linker (ldd) 2.2.3
> Procps 2.0.7
> Net-tools 1.60
> Kbd 1.06
> Sh-utils 2.0
> Modules Loaded iptable_filter ip_nat_ftp iptable_nat ip_conntrack_ftp ip_conntrack ip_tables apm ppp_deflate ppp_async ppp_generic slhc rtc nls_iso8859-1 nls_cp437 vfat fat
>
>
> [7.2.] Processor information (from /proc/cpuinfo):
>
> processor : 0
> vendor_id : AuthenticAMD
> cpu family : 6
> model : 2
> model name : AMD Athlon(tm) Processor
> stepping : 1
> cpu MHz : 800.047
> cache size : 512 KB
> fdiv_bug : no
> hlt_bug : no
> f00f_bug : no
> coma_bug : no
> fpu : yes
> fpu_exception : yes
> cpuid level : 1
> wp : yes
> flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr syscall mmxext 3dnowext 3dnow
> bogomips : 1595.80
>
>
> [7.3.] Module information (from /proc/modules):
>
> iptable_filter 1760 0 (autoclean) (unused)
> ip_nat_ftp 2944 0 (unused)
> iptable_nat 12880 1 [ip_nat_ftp]
> ip_conntrack_ftp 3184 0 (unused)
> ip_conntrack 13392 2 [ip_nat_ftp iptable_nat ip_conntrack_ftp]
> ip_tables 10560 4 [iptable_filter iptable_nat]
> apm 9440 1
> ppp_deflate 40160 0 (unused)
> ppp_async 6544 0 (unused)
> ppp_generic 15744 0 [ppp_deflate ppp_async]
> slhc 4624 0 [ppp_generic]
> rtc 6016 0 (autoclean)
> nls_iso8859-1 2880 1 (autoclean)
> nls_cp437 4384 1 (autoclean)
> vfat 9456 1 (autoclean)
> fat 29504 0 (autoclean) [vfat]
>
>
> [7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
>
> 0000-001f : dma1
> 0020-003f : pic1
> 0040-005f : timer
> 0060-006f : keyboard
> 0070-007f : rtc
> 0080-008f : dma page reg
> 00a0-00bf : pic2
> 00c0-00df : dma2
> 00f0-00ff : fpu
> 0170-0177 : ide1
> 01f0-01f7 : ide0
> 02f8-02ff : serial(auto)
> 0376-0376 : ide1
> 03c0-03df : vga+
> 03f6-03f6 : ide0
> 03f8-03ff : serial(auto)
> 0cf8-0cff : PCI conf1
> 7800-7807 : Creative Labs SB Live! MIDI/Game Port
> 8000-801f : Creative Labs SB Live! EMU10k1
> 8400-8407 : Lucent Microelectronics Venus Modem (V90, 56KFlex)
> 8800-88ff : Lucent Microelectronics Venus Modem (V90, 56KFlex)
> 9000-90ff : Lucent Microelectronics Venus Modem (V90, 56KFlex)
> 9000-9007 : serial(auto)
> 9400-947f : 3Com Corporation 3c905B 100BaseTX [Cyclone]
> 9400-947f : 00:09.0
> b000-b01f : VIA Technologies, Inc. UHCI USB (#2)
> b000-b01f : usb-uhci
> b400-b41f : VIA Technologies, Inc. UHCI USB
> b400-b41f : usb-uhci
> b800-b80f : VIA Technologies, Inc. Bus Master IDE
> b800-b807 : ide0
> b808-b80f : ide1
> d000-dfff : PCI Bus #01
> d800-d8ff : 3Dfx Interactive, Inc. Voodoo 3
> e400-e4ff : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
> e800-e80f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
>
>
> 00000000-0009fbff : System RAM
> 0009fc00-0009ffff : reserved
> 000a0000-000bffff : Video RAM area
> 000c0000-000c7fff : Video ROM
> 000f0000-000fffff : System ROM
> 00100000-0fffbfff : System RAM
> 00100000-00260f95 : Kernel code
> 00260f96-002ccaf7 : Kernel data
> 0fffc000-0fffefff : ACPI Tables
> 0ffff000-0fffffff : ACPI Non-volatile Storage
> dc800000-dc8000ff : Lucent Microelectronics Venus Modem (V90, 56KFlex)
> dd000000-dd0fffff : Sigma Designs, Inc. REALmagic Hollywood Plus DVD Decoder
> dd800000-dd80007f : 3Com Corporation 3c905B 100BaseTX [Cyclone]
> de000000-e1dfffff : PCI Bus #01
> de000000-dfffffff : 3Dfx Interactive, Inc. Voodoo 3
> e1f00000-e3ffffff : PCI Bus #01
> e2000000-e3ffffff : 3Dfx Interactive, Inc. Voodoo 3
> e4000000-e7ffffff : VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x]
> ffff0000-ffffffff : reserved
>
> [7.5.] PCI information ('lspci -vvv' as root)
>
> 00:00.0 Host bridge: VIA Technologies, Inc. VT82C691 [Apollo PRO] (rev 02)
> Subsystem: Asustek Computer, Inc.: Unknown device 8023
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
> Capabilities: [a0] AGP version 2.0
> Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
> Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
>
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP] (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: de000000-e1dfffff
> Prefetchable memory behind bridge: e1f00000-e3ffffff
> BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super] (rev 22)
> Subsystem: Asustek Computer, Inc.: Unknown device 8023
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:04.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 10) (prog-if 8a [Master SecP PriP])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Region 4: I/O ports at b800 [size=16]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10) (prog-if 00 [UHCI])
> Subsystem: Unknown device 0925:1234
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, cache line size 08
> Interrupt: pin D routed to IRQ 7
> Region 4: I/O ports at b400 [size=32]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.3 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10) (prog-if 00 [UHCI])
> Subsystem: Unknown device 0925:1234
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, cache line size 08
> Interrupt: pin D routed to IRQ 7
> Region 4: I/O ports at b000 [size=32]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin ? routed to IRQ 9
> Capabilities: [68] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:09.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
> Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (2500ns min, 2500ns max), cache line size 08
> Interrupt: pin A routed to IRQ 7
> Region 0: I/O ports at 9400 [size=128]
> Region 1: Memory at dd800000 (32-bit, non-prefetchable) [size=128]
> Expansion ROM at <unassigned> [disabled] [size=128K]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0a.0 Multimedia controller: Sigma Designs, Inc. REALmagic Hollywood Plus DVD Decoder (rev 02)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Interrupt: pin A routed to IRQ 10
> Region 0: Memory at dd000000 (32-bit, non-prefetchable) [size=1M]
> Capabilities: [40] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0b.0 Communication controller: Lucent Microelectronics Venus Modem (V90, 56KFlex)
> Subsystem: Action Tec Electronics Inc: Unknown device 0500
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (63000ns min, 3500ns max)
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at dc800000 (32-bit, non-prefetchable) [size=256]
> Region 1: I/O ports at 9000 [size=256]
> Region 2: I/O ports at 8800 [size=256]
> Region 3: I/O ports at 8400 [size=8]
> Capabilities: [f8] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0d.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 05)
> Subsystem: Creative Labs CT4620 SBLive!
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (500ns min, 5000ns max)
> Interrupt: pin A routed to IRQ 7
> Region 0: I/O ports at 8000 [size=32]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0d.1 Input device controller: Creative Labs SB Live! (rev 05)
> Subsystem: Creative Labs Gameport Joystick
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Region 0: I/O ports at 7800 [size=8]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 01:00.0 VGA compatible controller: 3Dfx Interactive, Inc. Voodoo 3 (rev 01) (prog-if 00 [VGA])
> Subsystem: 3Dfx Interactive, Inc. Voodoo3 AGP
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=32M]
> Region 1: Memory at e2000000 (32-bit, prefetchable) [size=32M]
> Region 2: I/O ports at d800 [size=256]
> Expansion ROM at e1ff0000 [disabled] [size=64K]
> Capabilities: [54] AGP version 1.0
> Status: RQ=7 SBA+ 64bit+ FW- Rate=x1,x2
> Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
> Capabilities: [60] Power Management version 1
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>
>
> [7.6.] SCSI information (from /proc/scsi/scsi)
>
> Attached devices: none
>
>
> [7.7.] Other information that might be relevant to the problem
> (please look in /proc and include all information that you
> think to be relevant):
>
> /proc/tty/driver/serial
> serinfo:1.0 driver:5.05c revision:2001-07-08
> 0: uart:16550A port:3F8 irq:4 baud:9600 tx:0 rx:0
> 1: uart:16550A port:2F8 irq:3 baud:9600 tx:0 rx:0
> 4: uart:16550A port:9000 irq:5 baud:9600 tx:0 rx:0 CTS|DSR
>
> /proc/tty/drivers
> serial /dev/cua 5 64-127 serial:callout
> serial /dev/ttyS 4 64-127 serial
> pty_slave /dev/pts 136 0-255 pty:slave
> pty_master /dev/ptm 128 0-255 pty:master
> pty_slave /dev/ttyp 3 0-255 pty:slave
> pty_master /dev/pty 2 0-255 pty:master
> /dev/vc/0 /dev/vc/0 4 0 system:vtmaster
> /dev/ptmx /dev/ptmx 5 2 system
> /dev/console /dev/console 5 1 system:console
> /dev/tty /dev/tty 5 0 system:/dev/tty
> unknown /dev/vc/%d 4 1-63 console
>
>
>
> [X.] Other notes, patches, fixes, workarounds:
> See description
>
>
> -------------------------------------------------------------
> -------------------------------------------------------------
> ---------- PATCHED KERNEL -----------------------------------
> -------------------------------------------------------------
> -------------------------------------------------------------
>
> The following is the output from the patched 2.4.19-rc2 kernel
> per my patch in the description
>
> [7.] Environment
> [7.1.] Software (add the output of the ver_linux script here)
>
> Linux delta 2.4.19-patch #6 Wed Jul 17 22:49:11 PDT 2002 i686 unknown
>
> Gnu C 2.95.3
> Gnu make 3.79.1
> binutils 2.11.90.0.19
> util-linux 2.11f
> mount 2.11b
> modutils 2.4.6
> e2fsprogs 1.27
> reiserfsprogs 3.x.0j
> pcmcia-cs 3.1.26
> PPP 2.4.1
> Linux C Library 2.2.3
> Dynamic linker (ldd) 2.2.3
> Procps 2.0.7
> Net-tools 1.60
> Kbd 1.06
> Sh-utils 2.0
> Modules Loaded iptable_filter ip_nat_ftp iptable_nat
> ip_conntrack_ftp ip_conntrack ip_tables apm ppp_deflate ppp_async
> ppp_generic slhc rtc nls_iso8859-1 nls_cp437 vfat fat
>
> [7.2.] Processor information (from /proc/cpuinfo):
>
> processor : 0
> vendor_id : AuthenticAMD
> cpu family : 6
> model : 2
> model name : AMD Athlon(tm) Processor
> stepping : 1
> cpu MHz : 800.057
> cache size : 512 KB
> fdiv_bug : no
> hlt_bug : no
> f00f_bug : no
> coma_bug : no
> fpu : yes
> fpu_exception : yes
> cpuid level : 1
> wp : yes
> flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr syscall mmxext 3dnowext 3dnow
> bogomips : 1595.80
>
>
> [7.3.] Module information (from /proc/modules):
>
> iptable_filter 1760 0 (autoclean) (unused)
> ip_nat_ftp 2944 0 (unused)
> iptable_nat 12880 1 [ip_nat_ftp]
> ip_conntrack_ftp 3184 0 (unused)
> ip_conntrack 13392 2 [ip_nat_ftp iptable_nat ip_conntrack_ftp]
> ip_tables 10560 4 [iptable_filter iptable_nat]
> apm 9440 1
> ppp_deflate 40160 0 (unused)
> ppp_async 6576 0 (unused)
> ppp_generic 15744 0 [ppp_deflate ppp_async]
> slhc 4624 0 [ppp_generic]
> rtc 6032 0 (autoclean)
> nls_iso8859-1 2880 1 (autoclean)
> nls_cp437 4400 1 (autoclean)
> vfat 9456 1 (autoclean)
> fat 29504 0 (autoclean) [vfat]
>
> [7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
>
> 0000-001f : dma1
> 0020-003f : pic1
> 0040-005f : timer
> 0060-006f : keyboard
> 0070-007f : rtc
> 0080-008f : dma page reg
> 00a0-00bf : pic2
> 00c0-00df : dma2
> 00f0-00ff : fpu
> 0170-0177 : ide1
> 01f0-01f7 : ide0
> 02f8-02ff : serial(auto)
> 0376-0376 : ide1
> 03c0-03df : vga+
> 03f6-03f6 : ide0
> 03f8-03ff : serial(auto)
> 0cf8-0cff : PCI conf1
> 7800-7807 : Creative Labs SB Live! MIDI/Game Port
> 8000-801f : Creative Labs SB Live! EMU10k1
> 8400-8407 : Lucent Microelectronics Venus Modem (V90, 56KFlex)
> 8800-88ff : Lucent Microelectronics Venus Modem (V90, 56KFlex)
> 9000-90ff : Lucent Microelectronics Venus Modem (V90, 56KFlex)
> 9000-9007 : serial(set)
> 9400-947f : 3Com Corporation 3c905B 100BaseTX [Cyclone]
> 9400-947f : 00:09.0
> b000-b01f : VIA Technologies, Inc. UHCI USB (#2)
> b000-b01f : usb-uhci
> b400-b41f : VIA Technologies, Inc. UHCI USB
> b400-b41f : usb-uhci
> b800-b80f : VIA Technologies, Inc. Bus Master IDE
> b800-b807 : ide0
> b808-b80f : ide1
> d000-dfff : PCI Bus #01
> d800-d8ff : 3Dfx Interactive, Inc. Voodoo 3
> e400-e4ff : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
> e800-e80f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
>
> 00000000-0009fbff : System RAM
> 0009fc00-0009ffff : reserved
> 000a0000-000bffff : Video RAM area
> 000c0000-000c7fff : Video ROM
> 000f0000-000fffff : System ROM
> 00100000-0fffbfff : System RAM
> 00100000-00260e25 : Kernel code
> 00260e26-002cc797 : Kernel data
> 0fffc000-0fffefff : ACPI Tables
> 0ffff000-0fffffff : ACPI Non-volatile Storage
> dc800000-dc8000ff : Lucent Microelectronics Venus Modem (V90, 56KFlex)
> dd000000-dd0fffff : Sigma Designs, Inc. REALmagic Hollywood Plus DVD Decoder
> dd800000-dd80007f : 3Com Corporation 3c905B 100BaseTX [Cyclone]
> de000000-e1dfffff : PCI Bus #01
> de000000-dfffffff : 3Dfx Interactive, Inc. Voodoo 3
> e1f00000-e3ffffff : PCI Bus #01
> e2000000-e3ffffff : 3Dfx Interactive, Inc. Voodoo 3
> e4000000-e7ffffff : VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x]
> ffff0000-ffffffff : reserved
>
>
> [7.5.] PCI information ('lspci -vvv' as root)
>
> 00:00.0 Host bridge: VIA Technologies, Inc. VT82C691 [Apollo PRO] (rev 02)
> Subsystem: Asustek Computer, Inc.: Unknown device 8023
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
> Capabilities: [a0] AGP version 2.0
> Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
> Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
>
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP] (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: de000000-e1dfffff
> Prefetchable memory behind bridge: e1f00000-e3ffffff
> BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super] (rev 22)
> Subsystem: Asustek Computer, Inc.: Unknown device 8023
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:04.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 10) (prog-if 8a [Master SecP PriP])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Region 4: I/O ports at b800 [size=16]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10) (prog-if 00 [UHCI])
> Subsystem: Unknown device 0925:1234
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, cache line size 08
> Interrupt: pin D routed to IRQ 7
> Region 4: I/O ports at b400 [size=32]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.3 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10) (prog-if 00 [UHCI])
> Subsystem: Unknown device 0925:1234
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, cache line size 08
> Interrupt: pin D routed to IRQ 7
> Region 4: I/O ports at b000 [size=32]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin ? routed to IRQ 9
> Capabilities: [68] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:09.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
> Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (2500ns min, 2500ns max), cache line size 08
> Interrupt: pin A routed to IRQ 7
> Region 0: I/O ports at 9400 [size=128]
> Region 1: Memory at dd800000 (32-bit, non-prefetchable) [size=128]
> Expansion ROM at <unassigned> [disabled] [size=128K]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0a.0 Multimedia controller: Sigma Designs, Inc. REALmagic Hollywood Plus DVD Decoder (rev 02)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Interrupt: pin A routed to IRQ 10
> Region 0: Memory at dd000000 (32-bit, non-prefetchable) [size=1M]
> Capabilities: [40] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0b.0 Communication controller: Lucent Microelectronics Venus Modem (V90, 56KFlex)
> Subsystem: Action Tec Electronics Inc: Unknown device 0500
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (63000ns min, 3500ns max)
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at dc800000 (32-bit, non-prefetchable) [size=256]
> Region 1: I/O ports at 9000 [size=256]
> Region 2: I/O ports at 8800 [size=256]
> Region 3: I/O ports at 8400 [size=8]
> Capabilities: [f8] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0d.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 05)
> Subsystem: Creative Labs CT4620 SBLive!
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (500ns min, 5000ns max)
> Interrupt: pin A routed to IRQ 7
> Region 0: I/O ports at 8000 [size=32]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0d.1 Input device controller: Creative Labs SB Live! (rev 05)
> Subsystem: Creative Labs Gameport Joystick
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Region 0: I/O ports at 7800 [size=8]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 01:00.0 VGA compatible controller: 3Dfx Interactive, Inc. Voodoo 3 (rev 01) (prog-if 00 [VGA])
> Subsystem: 3Dfx Interactive, Inc. Voodoo3 AGP
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=32M]
> Region 1: Memory at e2000000 (32-bit, prefetchable) [size=32M]
> Region 2: I/O ports at d800 [size=256]
> Expansion ROM at e1ff0000 [disabled] [size=64K]
> Capabilities: [54] AGP version 1.0
> Status: RQ=7 SBA+ 64bit+ FW- Rate=x1,x2
> Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
> Capabilities: [60] Power Management version 1
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>
> [7.6.] SCSI information (from /proc/scsi/scsi)
>
> Attached devices: none
>
> [7.7.] Other information that might be relevant to the problem
> (please look in /proc and include all information that you
> think to be relevant):
>
> /proc/tty/driver/serial
>
> serinfo:1.0 driver:5.05a revision:2001-03-20
> 0: uart:16550A port:3F8 irq:4 baud:9600 tx:0 rx:0
> 1: uart:16550A port:2F8 irq:3 baud:9600 tx:0 rx:0
> 2: uart:16550A port:9000 irq:5 baud:9600 tx:0 rx:0 CTS|DSR
> 3: uart:unknown port:2E8 irq:3
> 4: uart:unknown port:FFFFFFFF irq:0
> 5: uart:unknown port:1A0 irq:9
> 6: uart:unknown port:1A8 irq:9
> 7: uart:unknown port:1B0 irq:9
> 8: uart:unknown port:1B8 irq:9
> 9: uart:unknown port:2A0 irq:5
> 10: uart:unknown port:2A8 irq:5
> 11: uart:unknown port:2B0 irq:5
> 12: uart:unknown port:2B8 irq:5
> 13: uart:unknown port:330 irq:4
> 14: uart:unknown port:338 irq:4
> 15: uart:unknown port:0 irq:0
> 16: uart:unknown port:0 irq:0
> 17: uart:unknown port:100 irq:12
> 18: uart:unknown port:108 irq:12
> 19: uart:unknown port:110 irq:12
> 20: uart:unknown port:118 irq:12
> 21: uart:unknown port:120 irq:12
> 22: uart:unknown port:128 irq:12
> 23: uart:unknown port:130 irq:12
> 24: uart:unknown port:138 irq:12
> 25: uart:unknown port:140 irq:12
> 26: uart:unknown port:148 irq:12
> 27: uart:unknown port:150 irq:12
> 28: uart:unknown port:158 irq:12
> 29: uart:unknown port:160 irq:12
> 30: uart:unknown port:168 irq:12
> 31: uart:unknown port:170 irq:12
> 32: uart:unknown port:178 irq:12
> 33: uart:unknown port:0 irq:0
> 34: uart:unknown port:0 irq:0
> 35: uart:unknown port:0 irq:0
> 36: uart:unknown port:0 irq:0
> 37: uart:unknown port:0 irq:0
> 38: uart:unknown port:0 irq:0
> 39: uart:unknown port:0 irq:0
> 40: uart:unknown port:0 irq:0
> 41: uart:unknown port:0 irq:0
> 42: uart:unknown port:0 irq:0
> 43: uart:unknown port:0 irq:0
> 44: uart:unknown port:0 irq:0
> 45: uart:unknown port:0 irq:0
> 46: uart:unknown port:0 irq:0
> 47: uart:unknown port:0 irq:0
> 48: uart:unknown port:0 irq:0
> 49: uart:unknown port:0 irq:0
> 50: uart:unknown port:0 irq:0
> 51: uart:unknown port:0 irq:0
> 52: uart:unknown port:0 irq:0
> 53: uart:unknown port:0 irq:0
> 54: uart:unknown port:0 irq:0
> 55: uart:unknown port:0 irq:0
> 56: uart:unknown port:0 irq:0
> 57: uart:unknown port:0 irq:0
> 58: uart:unknown port:0 irq:0
> 59: uart:unknown port:0 irq:0
> 60: uart:unknown port:0 irq:0
> 61: uart:unknown port:0 irq:0
> 62: uart:unknown port:0 irq:0
> 63: uart:unknown port:0 irq:0
>
>
> /proc/tty/drivers
> serial /dev/cua 5 64-127 serial:callout
> serial /dev/ttyS 4 64-127 serial
> pty_slave /dev/pts 136 0-255 pty:slave
> pty_master /dev/ptm 128 0-255 pty:master
> pty_slave /dev/ttyp 3 0-255 pty:slave
> pty_master /dev/pty 2 0-255 pty:master
> /dev/vc/0 /dev/vc/0 4 0 system:vtmaster
> /dev/ptmx /dev/ptmx 5 2 system
> /dev/console /dev/console 5 1 system:console
> /dev/tty /dev/tty 5 0 system:/dev/tty
> unknown /dev/vc/%d 4 1-63 console
>
> #
> # Automatically generated by make menuconfig: don't edit
> #
> CONFIG_X86=y
> CONFIG_ISA=y
> # CONFIG_SBUS is not set
> CONFIG_UID16=y
>
> #
> # Code maturity level options
> #
> # CONFIG_EXPERIMENTAL is not set
>
> #
> # Loadable module support
> #
> CONFIG_MODULES=y
> # CONFIG_MODVERSIONS is not set
> CONFIG_KMOD=y
>
> #
> # Processor type and features
> #
> # CONFIG_M386 is not set
> # CONFIG_M486 is not set
> # CONFIG_M586 is not set
> # CONFIG_M586TSC is not set
> # CONFIG_M586MMX is not set
> # CONFIG_M686 is not set
> # CONFIG_MPENTIUMIII is not set
> # CONFIG_MPENTIUM4 is not set
> # CONFIG_MK6 is not set
> CONFIG_MK7=y
> # CONFIG_MELAN is not set
> # CONFIG_MCRUSOE is not set
> # CONFIG_MWINCHIPC6 is not set
> # CONFIG_MWINCHIP2 is not set
> # CONFIG_MWINCHIP3D is not set
> # CONFIG_MCYRIXIII is not set
> CONFIG_X86_WP_WORKS_OK=y
> CONFIG_X86_INVLPG=y
> CONFIG_X86_CMPXCHG=y
> CONFIG_X86_XADD=y
> CONFIG_X86_BSWAP=y
> CONFIG_X86_POPAD_OK=y
> # CONFIG_RWSEM_GENERIC_SPINLOCK is not set
> CONFIG_RWSEM_XCHGADD_ALGORITHM=y
> CONFIG_X86_L1_CACHE_SHIFT=6
> CONFIG_X86_TSC=y
> CONFIG_X86_GOOD_APIC=y
> CONFIG_X86_USE_3DNOW=y
> CONFIG_X86_PGE=y
> CONFIG_X86_USE_PPRO_CHECKSUM=y
> CONFIG_X86_MCE=y
> # CONFIG_TOSHIBA is not set
> # CONFIG_I8K is not set
> # CONFIG_MICROCODE is not set
> # CONFIG_X86_MSR is not set
> # CONFIG_X86_CPUID is not set
> CONFIG_NOHIGHMEM=y
> # CONFIG_HIGHMEM4G is not set
> # CONFIG_HIGHMEM64G is not set
> # CONFIG_MATH_EMULATION is not set
> CONFIG_MTRR=y
> # CONFIG_SMP is not set
> # CONFIG_X86_UP_APIC is not set
> # CONFIG_X86_UP_IOAPIC is not set
>
> #
> # General setup
> #
> CONFIG_NET=y
> CONFIG_PCI=y
> # CONFIG_PCI_GOBIOS is not set
> # CONFIG_PCI_GODIRECT is not set
> CONFIG_PCI_GOANY=y
> CONFIG_PCI_BIOS=y
> CONFIG_PCI_DIRECT=y
> CONFIG_PCI_NAMES=y
> # CONFIG_EISA is not set
> # CONFIG_MCA is not set
> CONFIG_HOTPLUG=y
>
> #
> # PCMCIA/CardBus support
> #
> CONFIG_PCMCIA=y
> CONFIG_CARDBUS=y
> # CONFIG_TCIC is not set
> # CONFIG_I82092 is not set
> # CONFIG_I82365 is not set
>
> #
> # PCI Hotplug Support
> #
> # CONFIG_HOTPLUG_PCI is not set
> # CONFIG_HOTPLUG_PCI_COMPAQ is not set
> # CONFIG_HOTPLUG_PCI_COMPAQ_NVRAM is not set
> # CONFIG_HOTPLUG_PCI_ACPI is not set
> CONFIG_SYSVIPC=y
> # CONFIG_BSD_PROCESS_ACCT is not set
> CONFIG_SYSCTL=y
> CONFIG_KCORE_ELF=y
> # CONFIG_KCORE_AOUT is not set
> CONFIG_BINFMT_AOUT=y
> CONFIG_BINFMT_ELF=y
> CONFIG_BINFMT_MISC=y
> CONFIG_PM=y
> CONFIG_APM=m
> # CONFIG_APM_IGNORE_USER_SUSPEND is not set
> # CONFIG_APM_DO_ENABLE is not set
> # CONFIG_APM_CPU_IDLE is not set
> CONFIG_APM_DISPLAY_BLANK=y
> # CONFIG_APM_RTC_IS_GMT is not set
> # CONFIG_APM_ALLOW_INTS is not set
> # CONFIG_APM_REAL_MODE_POWER_OFF is not set
>
> #
> # Memory Technology Devices (MTD)
> #
> # CONFIG_MTD is not set
>
> #
> # Parallel port support
> #
> # CONFIG_PARPORT is not set
>
> #
> # Plug and Play configuration
> #
> CONFIG_PNP=y
> CONFIG_ISAPNP=y
>
> #
> # Block devices
> #
> CONFIG_BLK_DEV_FD=y
> # CONFIG_BLK_DEV_XD is not set
> # CONFIG_PARIDE is not set
> # CONFIG_BLK_CPQ_DA is not set
> # CONFIG_BLK_CPQ_CISS_DA is not set
> # CONFIG_CISS_SCSI_TAPE is not set
> # CONFIG_BLK_DEV_DAC960 is not set
> # CONFIG_BLK_DEV_UMEM is not set
> CONFIG_BLK_DEV_LOOP=m
> CONFIG_BLK_DEV_NBD=m
> CONFIG_BLK_DEV_RAM=y
> CONFIG_BLK_DEV_RAM_SIZE=4096
> CONFIG_BLK_DEV_INITRD=y
>
> #
> # Multi-device support (RAID and LVM)
> #
> # CONFIG_MD is not set
> # CONFIG_BLK_DEV_MD is not set
> # CONFIG_MD_LINEAR is not set
> # CONFIG_MD_RAID0 is not set
> # CONFIG_MD_RAID1 is not set
> # CONFIG_MD_RAID5 is not set
> # CONFIG_MD_MULTIPATH is not set
> # CONFIG_BLK_DEV_LVM is not set
>
> #
> # Networking options
> #
> CONFIG_PACKET=y
> # CONFIG_PACKET_MMAP is not set
> # CONFIG_NETLINK_DEV is not set
> CONFIG_NETFILTER=y
> # CONFIG_NETFILTER_DEBUG is not set
> # CONFIG_FILTER is not set
> CONFIG_UNIX=y
> CONFIG_INET=y
> CONFIG_IP_MULTICAST=y
> # CONFIG_IP_ADVANCED_ROUTER is not set
> # CONFIG_IP_PNP is not set
> # CONFIG_NET_IPIP is not set
> # CONFIG_NET_IPGRE is not set
> # CONFIG_IP_MROUTE is not set
> # CONFIG_INET_ECN is not set
> # CONFIG_SYN_COOKIES is not set
>
> #
> # IP: Netfilter Configuration
> #
> CONFIG_IP_NF_CONNTRACK=m
> CONFIG_IP_NF_FTP=m
> # CONFIG_IP_NF_IRC is not set
> CONFIG_IP_NF_IPTABLES=m
> CONFIG_IP_NF_MATCH_LIMIT=m
> # CONFIG_IP_NF_MATCH_MAC is not set
> # CONFIG_IP_NF_MATCH_MARK is not set
> CONFIG_IP_NF_MATCH_MULTIPORT=m
> CONFIG_IP_NF_MATCH_TOS=m
> # CONFIG_IP_NF_MATCH_AH_ESP is not set
> # CONFIG_IP_NF_MATCH_LENGTH is not set
> # CONFIG_IP_NF_MATCH_TTL is not set
> # CONFIG_IP_NF_MATCH_TCPMSS is not set
> CONFIG_IP_NF_MATCH_STATE=m
> CONFIG_IP_NF_FILTER=m
> CONFIG_IP_NF_TARGET_REJECT=m
> CONFIG_IP_NF_NAT=m
> CONFIG_IP_NF_NAT_NEEDED=y
> CONFIG_IP_NF_TARGET_MASQUERADE=m
> CONFIG_IP_NF_TARGET_REDIRECT=m
> # CONFIG_IP_NF_NAT_LOCAL is not set
> CONFIG_IP_NF_NAT_FTP=m
> # CONFIG_IP_NF_MANGLE is not set
> CONFIG_IP_NF_TARGET_LOG=m
> # CONFIG_IP_NF_TARGET_ULOG is not set
> # CONFIG_IP_NF_TARGET_TCPMSS is not set
> # CONFIG_IP_NF_ARPTABLES is not set
> # CONFIG_IP_NF_COMPAT_IPCHAINS is not set
> # CONFIG_IP_NF_COMPAT_IPFWADM is not set
> # CONFIG_VLAN_8021Q is not set
> # CONFIG_IPX is not set
> # CONFIG_ATALK is not set
>
> #
> # Appletalk devices
> #
> # CONFIG_DEV_APPLETALK is not set
> # CONFIG_DECNET is not set
> # CONFIG_BRIDGE is not set
>
> #
> # QoS and/or fair queueing
> #
> # CONFIG_NET_SCHED is not set
>
> #
> # Network testing
> #
> # CONFIG_NET_PKTGEN is not set
>
> #
> # Telephony Support
> #
> # CONFIG_PHONE is not set
> # CONFIG_PHONE_IXJ is not set
> # CONFIG_PHONE_IXJ_PCMCIA is not set
>
> #
> # ATA/IDE/MFM/RLL support
> #
> CONFIG_IDE=y
>
> #
> # IDE, ATA and ATAPI Block devices
> #
> CONFIG_BLK_DEV_IDE=y
> # CONFIG_BLK_DEV_HD_IDE is not set
> # CONFIG_BLK_DEV_HD is not set
> CONFIG_BLK_DEV_IDEDISK=y
> # CONFIG_IDEDISK_MULTI_MODE is not set
> # CONFIG_IDEDISK_STROKE is not set
> # CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
> # CONFIG_BLK_DEV_IDEDISK_FUJITSU is not set
> # CONFIG_BLK_DEV_IDEDISK_IBM is not set
> # CONFIG_BLK_DEV_IDEDISK_MAXTOR is not set
> # CONFIG_BLK_DEV_IDEDISK_QUANTUM is not set
> # CONFIG_BLK_DEV_IDEDISK_SEAGATE is not set
> # CONFIG_BLK_DEV_IDEDISK_WD is not set
> # CONFIG_BLK_DEV_COMMERIAL is not set
> # CONFIG_BLK_DEV_TIVO is not set
> # CONFIG_BLK_DEV_IDECS is not set
> CONFIG_BLK_DEV_IDECD=m
> # CONFIG_BLK_DEV_IDETAPE is not set
> # CONFIG_BLK_DEV_IDEFLOPPY is not set
> CONFIG_BLK_DEV_IDESCSI=m
> # CONFIG_IDE_TASK_IOCTL is not set
> CONFIG_BLK_DEV_CMD640=y
> # CONFIG_BLK_DEV_CMD640_ENHANCED is not set
> # CONFIG_BLK_DEV_ISAPNP is not set
> CONFIG_BLK_DEV_RZ1000=y
> CONFIG_BLK_DEV_IDEPCI=y
> CONFIG_IDEPCI_SHARE_IRQ=y
> CONFIG_BLK_DEV_IDEDMA_PCI=y
> # CONFIG_BLK_DEV_OFFBOARD is not set
> # CONFIG_BLK_DEV_IDEDMA_FORCED is not set
> CONFIG_IDEDMA_PCI_AUTO=y
> # CONFIG_IDEDMA_ONLYDISK is not set
> CONFIG_BLK_DEV_IDEDMA=y
> # CONFIG_IDEDMA_PCI_WIP is not set
> # CONFIG_BLK_DEV_IDEDMA_TIMEOUT is not set
> # CONFIG_IDEDMA_NEW_DRIVE_LISTINGS is not set
> CONFIG_BLK_DEV_ADMA=y
> # CONFIG_BLK_DEV_AEC62XX is not set
> # CONFIG_AEC62XX_TUNING is not set
> # CONFIG_BLK_DEV_ALI15X3 is not set
> # CONFIG_WDC_ALI15X3 is not set
> # CONFIG_BLK_DEV_AMD74XX is not set
> # CONFIG_AMD74XX_OVERRIDE is not set
> # CONFIG_BLK_DEV_CMD64X is not set
> # CONFIG_BLK_DEV_CMD680 is not set
> # CONFIG_BLK_DEV_CY82C693 is not set
> # CONFIG_BLK_DEV_CS5530 is not set
> # CONFIG_BLK_DEV_HPT34X is not set
> # CONFIG_HPT34X_AUTODMA is not set
> # CONFIG_BLK_DEV_HPT366 is not set
> CONFIG_BLK_DEV_PIIX=y
> CONFIG_PIIX_TUNING=y
> # CONFIG_BLK_DEV_NS87415 is not set
> # CONFIG_BLK_DEV_OPTI621 is not set
> # CONFIG_BLK_DEV_PDC202XX is not set
> # CONFIG_PDC202XX_BURST is not set
> # CONFIG_PDC202XX_FORCE is not set
> # CONFIG_BLK_DEV_SVWKS is not set
> # CONFIG_BLK_DEV_SIS5513 is not set
> # CONFIG_BLK_DEV_SLC90E66 is not set
> # CONFIG_BLK_DEV_TRM290 is not set
> CONFIG_BLK_DEV_VIA82CXXX=y
> # CONFIG_IDE_CHIPSETS is not set
> CONFIG_IDEDMA_AUTO=y
> # CONFIG_IDEDMA_IVB is not set
> # CONFIG_DMA_NONPCI is not set
> CONFIG_BLK_DEV_IDE_MODES=y
> # CONFIG_BLK_DEV_ATARAID is not set
> # CONFIG_BLK_DEV_ATARAID_PDC is not set
> # CONFIG_BLK_DEV_ATARAID_HPT is not set
>
> #
> # SCSI support
> #
> CONFIG_SCSI=y
> # CONFIG_BLK_DEV_SD is not set
> # CONFIG_CHR_DEV_ST is not set
> # CONFIG_CHR_DEV_OSST is not set
> CONFIG_BLK_DEV_SR=y
> CONFIG_BLK_DEV_SR_VENDOR=y
> CONFIG_SR_EXTRA_DEVS=2
> CONFIG_CHR_DEV_SG=y
> CONFIG_SCSI_DEBUG_QUEUES=y
> CONFIG_SCSI_MULTI_LUN=y
> CONFIG_SCSI_CONSTANTS=y
> # CONFIG_SCSI_LOGGING is not set
>
> #
> # SCSI low-level drivers
> #
> # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
> # CONFIG_SCSI_7000FASST is not set
> # CONFIG_SCSI_ACARD is not set
> # CONFIG_SCSI_AHA152X is not set
> # CONFIG_SCSI_AHA1542 is not set
> # CONFIG_SCSI_AHA1740 is not set
> # CONFIG_SCSI_AIC7XXX is not set
> # CONFIG_SCSI_AIC7XXX_OLD is not set
> # CONFIG_SCSI_DPT_I2O is not set
> # CONFIG_SCSI_ADVANSYS is not set
> # CONFIG_SCSI_IN2000 is not set
> # CONFIG_SCSI_AM53C974 is not set
> # CONFIG_SCSI_MEGARAID is not set
> # CONFIG_SCSI_BUSLOGIC is not set
> # CONFIG_SCSI_CPQFCTS is not set
> # CONFIG_SCSI_DMX3191D is not set
> # CONFIG_SCSI_DTC3280 is not set
> # CONFIG_SCSI_EATA is not set
> # CONFIG_SCSI_EATA_DMA is not set
> # CONFIG_SCSI_EATA_PIO is not set
> # CONFIG_SCSI_FUTURE_DOMAIN is not set
> # CONFIG_SCSI_GDTH is not set
> # CONFIG_SCSI_GENERIC_NCR5380 is not set
> # CONFIG_SCSI_IPS is not set
> # CONFIG_SCSI_INITIO is not set
> # CONFIG_SCSI_INIA100 is not set
> # CONFIG_SCSI_NCR53C406A is not set
> # CONFIG_SCSI_NCR53C7xx is not set
> # CONFIG_SCSI_SYM53C8XX_2 is not set
> # CONFIG_SCSI_NCR53C8XX is not set
> CONFIG_SCSI_SYM53C8XX=m
> CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS=4
> CONFIG_SCSI_NCR53C8XX_MAX_TAGS=32
> CONFIG_SCSI_NCR53C8XX_SYNC=20
> # CONFIG_SCSI_NCR53C8XX_PROFILE is not set
> # CONFIG_SCSI_NCR53C8XX_IOMAPPED is not set
> # CONFIG_SCSI_NCR53C8XX_PQS_PDS is not set
> # CONFIG_SCSI_PAS16 is not set
> # CONFIG_SCSI_PCI2000 is not set
> # CONFIG_SCSI_PCI2220I is not set
> # CONFIG_SCSI_PSI240I is not set
> # CONFIG_SCSI_QLOGIC_FAS is not set
> # CONFIG_SCSI_QLOGIC_ISP is not set
> # CONFIG_SCSI_QLOGIC_FC is not set
> # CONFIG_SCSI_QLOGIC_1280 is not set
> # CONFIG_SCSI_SEAGATE is not set
> # CONFIG_SCSI_SIM710 is not set
> # CONFIG_SCSI_SYM53C416 is not set
> # CONFIG_SCSI_DC390T is not set
> # CONFIG_SCSI_T128 is not set
> # CONFIG_SCSI_U14_34F is not set
> # CONFIG_SCSI_ULTRASTOR is not set
>
> #
> # PCMCIA SCSI adapter support
> #
> # CONFIG_SCSI_PCMCIA is not set
>
> #
> # Fusion MPT device support
> #
> # CONFIG_FUSION is not set
> # CONFIG_FUSION_BOOT is not set
> # CONFIG_FUSION_ISENSE is not set
> # CONFIG_FUSION_CTL is not set
> # CONFIG_FUSION_LAN is not set
>
> #
> # I2O device support
> #
> # CONFIG_I2O is not set
> # CONFIG_I2O_PCI is not set
> # CONFIG_I2O_BLOCK is not set
> # CONFIG_I2O_LAN is not set
> # CONFIG_I2O_SCSI is not set
> # CONFIG_I2O_PROC is not set
>
> #
> # Network device support
> #
> CONFIG_NETDEVICES=y
>
> #
> # ARCnet devices
> #
> # CONFIG_ARCNET is not set
> CONFIG_DUMMY=m
> # CONFIG_BONDING is not set
> # CONFIG_EQUALIZER is not set
> # CONFIG_TUN is not set
> # CONFIG_NET_SB1000 is not set
>
> #
> # Ethernet (10 or 100Mbit)
> #
> CONFIG_NET_ETHERNET=y
> # CONFIG_SUNLANCE is not set
> # CONFIG_HAPPYMEAL is not set
> # CONFIG_SUNBMAC is not set
> # CONFIG_SUNQE is not set
> # CONFIG_SUNGEM is not set
> CONFIG_NET_VENDOR_3COM=y
> # CONFIG_EL1 is not set
> # CONFIG_EL2 is not set
> # CONFIG_ELPLUS is not set
> # CONFIG_EL16 is not set
> # CONFIG_EL3 is not set
> # CONFIG_3C515 is not set
> # CONFIG_ELMC is not set
> # CONFIG_ELMC_II is not set
> CONFIG_VORTEX=y
> # CONFIG_LANCE is not set
> # CONFIG_NET_VENDOR_SMC is not set
> # CONFIG_NET_VENDOR_RACAL is not set
> # CONFIG_AT1700 is not set
> # CONFIG_DEPCA is not set
> # CONFIG_HP100 is not set
> # CONFIG_NET_ISA is not set
> CONFIG_NET_PCI=y
> # CONFIG_PCNET32 is not set
> # CONFIG_ADAPTEC_STARFIRE is not set
> # CONFIG_AC3200 is not set
> # CONFIG_APRICOT is not set
> # CONFIG_CS89x0 is not set
> # CONFIG_TULIP is not set
> # CONFIG_TC35815 is not set
> # CONFIG_DE4X5 is not set
> # CONFIG_DGRS is not set
> # CONFIG_DM9102 is not set
> CONFIG_EEPRO100=y
> # CONFIG_LNE390 is not set
> # CONFIG_FEALNX is not set
> # CONFIG_NATSEMI is not set
> # CONFIG_NE2K_PCI is not set
> # CONFIG_NE3210 is not set
> # CONFIG_ES3210 is not set
> # CONFIG_8139CP is not set
> # CONFIG_8139TOO is not set
> # CONFIG_8139TOO_PIO is not set
> # CONFIG_8139TOO_TUNE_TWISTER is not set
> # CONFIG_8139TOO_8129 is not set
> # CONFIG_8139_NEW_RX_RESET is not set
> # CONFIG_SIS900 is not set
> # CONFIG_EPIC100 is not set
> # CONFIG_SUNDANCE is not set
> # CONFIG_TLAN is not set
> # CONFIG_VIA_RHINE is not set
> # CONFIG_VIA_RHINE_MMIO is not set
> # CONFIG_WINBOND_840 is not set
> # CONFIG_NET_POCKET is not set
>
> #
> # Ethernet (1000 Mbit)
> #
> # CONFIG_ACENIC is not set
> # CONFIG_DL2K is not set
> # CONFIG_MYRI_SBUS is not set
> # CONFIG_NS83820 is not set
> # CONFIG_HAMACHI is not set
> # CONFIG_YELLOWFIN is not set
> # CONFIG_SK98LIN is not set
> # CONFIG_TIGON3 is not set
> # CONFIG_FDDI is not set
> # CONFIG_PLIP is not set
> CONFIG_PPP=m
> # CONFIG_PPP_MULTILINK is not set
> # CONFIG_PPP_FILTER is not set
> CONFIG_PPP_ASYNC=m
> CONFIG_PPP_SYNC_TTY=m
> CONFIG_PPP_DEFLATE=m
> CONFIG_PPP_BSDCOMP=m
> # CONFIG_PPPOATM is not set
> # CONFIG_SLIP is not set
>
> #
> # Wireless LAN (non-hamradio)
> #
> # CONFIG_NET_RADIO is not set
>
> #
> # Token Ring devices
> #
> # CONFIG_TR is not set
> # CONFIG_NET_FC is not set
>
> #
> # Wan interfaces
> #
> # CONFIG_WAN is not set
>
> #
> # PCMCIA network device support
> #
> # CONFIG_NET_PCMCIA is not set
>
> #
> # Amateur Radio support
> #
> # CONFIG_HAMRADIO is not set
>
> #
> # IrDA (infrared) support
> #
> # CONFIG_IRDA is not set
>
> #
> # ISDN subsystem
> #
> # CONFIG_ISDN is not set
>
> #
> # Old CD-ROM drivers (not SCSI, not IDE)
> #
> # CONFIG_CD_NO_IDESCSI is not set
>
> #
> # Input core support
> #
> # CONFIG_INPUT is not set
> # CONFIG_INPUT_KEYBDEV is not set
> # CONFIG_INPUT_MOUSEDEV is not set
> # CONFIG_INPUT_JOYDEV is not set
> # CONFIG_INPUT_EVDEV is not set
>
> #
> # Character devices
> #
> CONFIG_VT=y
> CONFIG_VT_CONSOLE=y
> CONFIG_SERIAL=y
> # CONFIG_SERIAL_CONSOLE is not set
> # CONFIG_SERIAL_EXTENDED is not set
> CONFIG_SERIAL_NONSTANDARD=y
> # CONFIG_COMPUTONE is not set
> # CONFIG_ROCKETPORT is not set
> # CONFIG_CYCLADES is not set
> # CONFIG_DIGIEPCA is not set
> # CONFIG_DIGI is not set
> # CONFIG_ESPSERIAL is not set
> # CONFIG_MOXA_INTELLIO is not set
> # CONFIG_MOXA_SMARTIO is not set
> # CONFIG_SYNCLINK is not set
> CONFIG_N_HDLC=m
> # CONFIG_RISCOM8 is not set
> # CONFIG_SPECIALIX is not set
> # CONFIG_SX is not set
> # CONFIG_RIO is not set
> # CONFIG_STALDRV is not set
> CONFIG_UNIX98_PTYS=y
> CONFIG_UNIX98_PTY_COUNT=256
>
> #
> # I2C support
> #
> # CONFIG_I2C is not set
>
> #
> # Mice
> #
> # CONFIG_BUSMOUSE is not set
> CONFIG_MOUSE=y
> CONFIG_PSMOUSE=y
> # CONFIG_82C710_MOUSE is not set
> # CONFIG_PC110_PAD is not set
> # CONFIG_MK712_MOUSE is not set
>
> #
> # Joysticks
> #
> # CONFIG_INPUT_GAMEPORT is not set
> # CONFIG_QIC02_TAPE is not set
>
> #
> # Watchdog Cards
> #
> # CONFIG_WATCHDOG is not set
> # CONFIG_AMD_RNG is not set
> CONFIG_INTEL_RNG=m
> # CONFIG_NVRAM is not set
> CONFIG_RTC=m
> # CONFIG_DTLK is not set
> # CONFIG_R3964 is not set
> # CONFIG_APPLICOM is not set
>
> #
> # Ftape, the floppy tape device driver
> #
> # CONFIG_FTAPE is not set
> CONFIG_AGP=y
> CONFIG_AGP_INTEL=y
> CONFIG_AGP_I810=y
> CONFIG_AGP_VIA=y
> CONFIG_AGP_AMD=y
> CONFIG_AGP_SIS=y
> CONFIG_AGP_ALI=y
> # CONFIG_AGP_SWORKS is not set
> CONFIG_DRM=y
> # CONFIG_DRM_OLD is not set
> CONFIG_DRM_NEW=y
> CONFIG_DRM_TDFX=y
> # CONFIG_DRM_R128 is not set
> CONFIG_DRM_RADEON=y
> # CONFIG_DRM_I810 is not set
> # CONFIG_DRM_MGA is not set
> # CONFIG_DRM_SIS is not set
>
> #
> # PCMCIA character devices
> #
> # CONFIG_PCMCIA_SERIAL_CS is not set
> # CONFIG_MWAVE is not set
>
> #
> # Multimedia devices
> #
> # CONFIG_VIDEO_DEV is not set
>
> #
> # File systems
> #
> # CONFIG_QUOTA is not set
> # CONFIG_AUTOFS_FS is not set
> CONFIG_AUTOFS4_FS=y
> # CONFIG_REISERFS_FS is not set
> # CONFIG_REISERFS_CHECK is not set
> # CONFIG_REISERFS_PROC_INFO is not set
> # CONFIG_ADFS_FS is not set
> # CONFIG_ADFS_FS_RW is not set
> # CONFIG_AFFS_FS is not set
> # CONFIG_HFS_FS is not set
> # CONFIG_BFS_FS is not set
> CONFIG_EXT3_FS=y
> CONFIG_JBD=y
> CONFIG_JBD_DEBUG=y
> CONFIG_FAT_FS=m
> CONFIG_MSDOS_FS=m
> # CONFIG_UMSDOS_FS is not set
> CONFIG_VFAT_FS=m
> # CONFIG_EFS_FS is not set
> # CONFIG_JFFS_FS is not set
> # CONFIG_JFFS2_FS is not set
> # CONFIG_CRAMFS is not set
> CONFIG_TMPFS=y
> CONFIG_RAMFS=y
> CONFIG_ISO9660_FS=y
> CONFIG_JOLIET=y
> # CONFIG_ZISOFS is not set
> CONFIG_MINIX_FS=m
> # CONFIG_VXFS_FS is not set
> # CONFIG_NTFS_FS is not set
> # CONFIG_NTFS_RW is not set
> # CONFIG_HPFS_FS is not set
> CONFIG_PROC_FS=y
> # CONFIG_DEVFS_FS is not set
> # CONFIG_DEVFS_MOUNT is not set
> # CONFIG_DEVFS_DEBUG is not set
> CONFIG_DEVPTS_FS=y
> # CONFIG_QNX4FS_FS is not set
> # CONFIG_QNX4FS_RW is not set
> # CONFIG_ROMFS_FS is not set
> CONFIG_EXT2_FS=y
> # CONFIG_SYSV_FS is not set
> # CONFIG_UDF_FS is not set
> # CONFIG_UDF_RW is not set
> # CONFIG_UFS_FS is not set
> # CONFIG_UFS_FS_WRITE is not set
>
> #
> # Network File Systems
> #
> # CONFIG_CODA_FS is not set
> # CONFIG_INTERMEZZO_FS is not set
> CONFIG_NFS_FS=y
> CONFIG_NFS_V3=y
> # CONFIG_ROOT_NFS is not set
> CONFIG_NFSD=y
> CONFIG_NFSD_V3=y
> CONFIG_SUNRPC=y
> CONFIG_LOCKD=y
> CONFIG_LOCKD_V4=y
> CONFIG_SMB_FS=m
> # CONFIG_SMB_NLS_DEFAULT is not set
> # CONFIG_NCP_FS is not set
> # CONFIG_NCPFS_PACKET_SIGNING is not set
> # CONFIG_NCPFS_IOCTL_LOCKING is not set
> # CONFIG_NCPFS_STRONG is not set
> # CONFIG_NCPFS_NFS_NS is not set
> # CONFIG_NCPFS_OS2_NS is not set
> # CONFIG_NCPFS_SMALLDOS is not set
> # CONFIG_NCPFS_NLS is not set
> # CONFIG_NCPFS_EXTRAS is not set
> # CONFIG_ZISOFS_FS is not set
> # CONFIG_ZLIB_FS_INFLATE is not set
>
> #
> # Partition Types
> #
> # CONFIG_PARTITION_ADVANCED is not set
> CONFIG_MSDOS_PARTITION=y
> CONFIG_SMB_NLS=y
> CONFIG_NLS=y
>
> #
> # Native Language Support
> #
> CONFIG_NLS_DEFAULT="iso8859-1"
> CONFIG_NLS_CODEPAGE_437=m
> # CONFIG_NLS_CODEPAGE_737 is not set
> # CONFIG_NLS_CODEPAGE_775 is not set
> # CONFIG_NLS_CODEPAGE_850 is not set
> CONFIG_NLS_CODEPAGE_852=m
> # CONFIG_NLS_CODEPAGE_855 is not set
> # CONFIG_NLS_CODEPAGE_857 is not set
> # CONFIG_NLS_CODEPAGE_860 is not set
> # CONFIG_NLS_CODEPAGE_861 is not set
> # CONFIG_NLS_CODEPAGE_862 is not set
> # CONFIG_NLS_CODEPAGE_863 is not set
> # CONFIG_NLS_CODEPAGE_864 is not set
> # CONFIG_NLS_CODEPAGE_865 is not set
> # CONFIG_NLS_CODEPAGE_866 is not set
> # CONFIG_NLS_CODEPAGE_869 is not set
> # CONFIG_NLS_CODEPAGE_936 is not set
> # CONFIG_NLS_CODEPAGE_950 is not set
> CONFIG_NLS_CODEPAGE_932=m
> # CONFIG_NLS_CODEPAGE_949 is not set
> # CONFIG_NLS_CODEPAGE_874 is not set
> # CONFIG_NLS_ISO8859_8 is not set
> # CONFIG_NLS_CODEPAGE_1250 is not set
> # CONFIG_NLS_CODEPAGE_1251 is not set
> CONFIG_NLS_ISO8859_1=m
> # CONFIG_NLS_ISO8859_2 is not set
> # CONFIG_NLS_ISO8859_3 is not set
> # CONFIG_NLS_ISO8859_4 is not set
> # CONFIG_NLS_ISO8859_5 is not set
> # CONFIG_NLS_ISO8859_6 is not set
> # CONFIG_NLS_ISO8859_7 is not set
> # CONFIG_NLS_ISO8859_9 is not set
> # CONFIG_NLS_ISO8859_13 is not set
> # CONFIG_NLS_ISO8859_14 is not set
> # CONFIG_NLS_ISO8859_15 is not set
> # CONFIG_NLS_KOI8_R is not set
> # CONFIG_NLS_KOI8_U is not set
> CONFIG_NLS_UTF8=m
>
> #
> # Console drivers
> #
> CONFIG_VGA_CONSOLE=y
> # CONFIG_VIDEO_SELECT is not set
>
> #
> # Sound
> #
> CONFIG_SOUND=y
> # CONFIG_SOUND_BT878 is not set
> # CONFIG_SOUND_CMPCI is not set
> CONFIG_SOUND_EMU10K1=m
> # CONFIG_MIDI_EMU10K1 is not set
> # CONFIG_SOUND_FUSION is not set
> # CONFIG_SOUND_CS4281 is not set
> # CONFIG_SOUND_ES1370 is not set
> # CONFIG_SOUND_ES1371 is not set
> # CONFIG_SOUND_ESSSOLO1 is not set
> # CONFIG_SOUND_MAESTRO is not set
> # CONFIG_SOUND_MAESTRO3 is not set
> # CONFIG_SOUND_ICH is not set
> # CONFIG_SOUND_RME96XX is not set
> # CONFIG_SOUND_SONICVIBES is not set
> # CONFIG_SOUND_TRIDENT is not set
> # CONFIG_SOUND_MSNDCLAS is not set
> # CONFIG_SOUND_MSNDPIN is not set
> # CONFIG_SOUND_VIA82CXXX is not set
> # CONFIG_MIDI_VIA82CXXX is not set
> # CONFIG_SOUND_OSS is not set
> # CONFIG_SOUND_TVMIXER is not set
>
> #
> # USB support
> #
> CONFIG_USB=y
> # CONFIG_USB_DEBUG is not set
> # CONFIG_USB_DEVICEFS is not set
> # CONFIG_USB_BANDWIDTH is not set
> # CONFIG_USB_LONG_TIMEOUT is not set
> # CONFIG_USB_EHCI_HCD is not set
> CONFIG_USB_UHCI_ALT=y
> # CONFIG_USB_OHCI is not set
> # CONFIG_USB_AUDIO is not set
> # CONFIG_USB_EMI26 is not set
> # CONFIG_USB_BLUETOOTH is not set
> # CONFIG_USB_STORAGE is not set
> # CONFIG_USB_STORAGE_DEBUG is not set
> # CONFIG_USB_STORAGE_DATAFAB is not set
> # CONFIG_USB_STORAGE_FREECOM is not set
> # CONFIG_USB_STORAGE_ISD200 is not set
> # CONFIG_USB_STORAGE_DPCM is not set
> # CONFIG_USB_STORAGE_HP8200e is not set
> # CONFIG_USB_STORAGE_SDDR09 is not set
> # CONFIG_USB_STORAGE_JUMPSHOT is not set
> # CONFIG_USB_ACM is not set
> CONFIG_USB_PRINTER=m
> # CONFIG_USB_HID is not set
> # CONFIG_USB_HIDINPUT is not set
> # CONFIG_USB_HIDDEV is not set
> # CONFIG_USB_KBD is not set
> # CONFIG_USB_MOUSE is not set
> # CONFIG_USB_WACOM is not set
> # CONFIG_USB_DC2XX is not set
> # CONFIG_USB_MDC800 is not set
> CONFIG_USB_SCANNER=m
> # CONFIG_USB_MICROTEK is not set
> # CONFIG_USB_HPUSBSCSI is not set
> # CONFIG_USB_PEGASUS is not set
> # CONFIG_USB_RTL8150 is not set
> # CONFIG_USB_KAWETH is not set
> # CONFIG_USB_CATC is not set
> # CONFIG_USB_CDCETHER is not set
> # CONFIG_USB_USBNET is not set
> # CONFIG_USB_USS720 is not set
>
> #
> # USB Serial Converter support
> #
> # CONFIG_USB_SERIAL is not set
> # CONFIG_USB_SERIAL_GENERIC is not set
> # CONFIG_USB_SERIAL_BELKIN is not set
> # CONFIG_USB_SERIAL_WHITEHEAT is not set
> # CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
> # CONFIG_USB_SERIAL_EMPEG is not set
> # CONFIG_USB_SERIAL_FTDI_SIO is not set
> # CONFIG_USB_SERIAL_VISOR is not set
> # CONFIG_USB_SERIAL_IPAQ is not set
> # CONFIG_USB_SERIAL_IR is not set
> # CONFIG_USB_SERIAL_EDGEPORT is not set
> # CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
> # CONFIG_USB_SERIAL_KEYSPAN is not set
> # CONFIG_USB_SERIAL_KEYSPAN_USA28 is not set
> # CONFIG_USB_SERIAL_KEYSPAN_USA28X is not set
> # CONFIG_USB_SERIAL_KEYSPAN_USA28XA is not set
> # CONFIG_USB_SERIAL_KEYSPAN_USA28XB is not set
> # CONFIG_USB_SERIAL_KEYSPAN_USA19 is not set
> # CONFIG_USB_SERIAL_KEYSPAN_USA18X is not set
> # CONFIG_USB_SERIAL_KEYSPAN_USA19W is not set
> # CONFIG_USB_SERIAL_KEYSPAN_USA49W is not set
> # CONFIG_USB_SERIAL_MCT_U232 is not set
> # CONFIG_USB_SERIAL_KLSI is not set
> # CONFIG_USB_SERIAL_PL2303 is not set
> # CONFIG_USB_SERIAL_CYBERJACK is not set
> # CONFIG_USB_SERIAL_XIRCOM is not set
> # CONFIG_USB_SERIAL_OMNINET is not set
> # CONFIG_USB_RIO500 is not set
> # CONFIG_USB_AUERSWALD is not set
> # CONFIG_USB_BRLVGER is not set
>
> #
> # Bluetooth support
> #
> # CONFIG_BLUEZ is not set
>
> #
> # Kernel hacking
> #
> # CONFIG_DEBUG_KERNEL is not set
-- -Steven In a time of universal deceit, telling the truth is a revolutionary act. -- George Orwell This concept of "wuv" confuses and infuriates us! -- Lur of Omicron Persei VIII - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/