I apologize for the size of this post. I imagine that you'll
also need lspci -v and .config information, but I'll wait for
someone to ask for it.
Linux version 2.5.20 (root@turbulence.megapathdsl.net) (gcc version 3.0.4 (Red Hat Linux 7.2 3.0.4-1)) #22Video mode to be used for restore is f00
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000ffe0000 (usable)
BIOS-e820: 000000000ffe0000 - 000000000fff8000 (ACPI data)
BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65504
zone(0): 4096 pages.
zone(1): 61408 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 AMI ) @ 0x000fae70
ACPI: RSDT (v001 GATEWA 8DT-084 00529.06553) @ 0x0fff0000
ACPI: FADT (v001 GATEWA 8DT-084 00529.06553) @ 0x0fff1000
ACPI: MADT not present
Kernel command line: ro root=/dev/hda6 hdd=ide-scsi console=ttyS0,38400 console=tty0 video=riva:1600x1200-16
ide_setup: hdd=ide-scsi
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 848.370 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1690.82 BogoMIPS
Memory: 255648k/262016k available (2231k kernel code, 5980k reserved, 566k data, 256k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Machine check exception polling timer started.
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Intel machine check reporting enabled on CPU#0.
WARNING: This combination of AMD processors is not suitable for SMP.
CPU0: AMD Athlon(tm) Processor stepping 01
per-CPU timeslice cutoff: 1462.63 usecs.
task migration cache decay timeout: 10 msecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 848.3522 MHz.
..... host bus clock speed is 199.6121 MHz.
cpu: 0, clocks: 1996121, slice: 998060
CPU0<T0:1996112,T1:998048,D:4,S:998060,C:1996121>
migration_task 0 on cpu=0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
PCI: PCI BIOS revision 2.10 entry at 0xfdad1, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20020517
tbxface-0100 [03] Acpi_load_tables : ACPI Tables successfully loaded
Parsing Methods:...................................................................................
Table [DSDT] - 271 Objects with 26 Devices 83 Methods 15 Regions
ACPI Namespace successfully loaded at root c0450d7c
evxfevnt-0076 [04] Acpi_enable : Transition to ACPI mode successful
Executing all Device _STA and_INI methods:............... exfldio-0098 [47] Ex_setup_region : Field) exfldio-0108 [47] Ex_setup_region : Field [PS2E] Base+Offset+Width 0+0+4 is beyond end of region [) uteval-0430 [34] Ut_execute_STA : No object was returned from _STA
...........
26 Devices found containing: 25 _STA, 2 _INI methods
Completing Region/Field/Buffer/Package initialization:..........................................
Initialized 12/15 Regions 1/1 Fields 21/21 Buffers 8/9 Packages (271 nodes)
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
exfldio-0098 [76] Ex_setup_region : Field [PS2E] access width (4 bytes) too large for region [PSRG) exfldio-0108 [76] Ex_setup_region : Field [PS2E] Base+Offset+Width 0+0+4 is beyond end of region [)pci_link-0152 [114] acpi_pci_link_get_poss: Resource is not an IRQ entry
pci_link-0152 [116] acpi_pci_link_get_poss: Resource is not an IRQ entry
pci_link-0152 [118] acpi_pci_link_get_poss: Resource is not an IRQ entry
pci_link-0152 [120] acpi_pci_link_get_poss: Resource is not an IRQ entry
pci_link-0465 [116] acpi_pci_link_get_irq : Invalid link context
pci_irq-0288 [115] acpi_pci_irq_derive : Unable to derive IRQ for device 00:07.4
pci_link-0465 [116] acpi_pci_link_get_irq : Invalid link context
pci_irq-0288 [115] acpi_pci_irq_derive : Unable to derive IRQ for device 00:0f.0
pci_link-0465 [116] acpi_pci_link_get_irq : Invalid link context
pci_irq-0288 [115] acpi_pci_irq_derive : Unable to derive IRQ for device 00:11.0
pci_link-0465 [116] acpi_pci_link_get_irq : Invalid link context
pci_irq-0288 [115] acpi_pci_irq_derive : Unable to derive IRQ for device 00:11.1
pci_link-0465 [116] acpi_pci_link_get_irq : Invalid link context
pci_irq-0288 [115] acpi_pci_irq_derive : Unable to derive IRQ for device 00:11.2
pci_link-0465 [116] acpi_pci_link_get_irq : Invalid link context
pci_irq-0288 [115] acpi_pci_irq_derive : Unable to derive IRQ for device 00:12.0
pci_link-0465 [116] acpi_pci_link_get_irq : Invalid link context
pci_irq-0288 [115] acpi_pci_irq_derive : Unable to derive IRQ for device 00:13.0
pci_link-0465 [116] acpi_pci_link_get_irq : Invalid link context
pci_irq-0288 [115] acpi_pci_irq_derive : Unable to derive IRQ for device 00:14.0
PCI: No IRQ known for interrupt pin A of device 00:14.0
pci_link-0465 [116] acpi_pci_link_get_irq : Invalid link context
pci_irq-0288 [115] acpi_pci_irq_derive : Unable to derive IRQ for device 00:14.1
PCI: No IRQ known for interrupt pin B of device 00:14.1
pci_link-0465 [116] acpi_pci_link_get_irq : Invalid link context
pci_irq-0288 [115] acpi_pci_irq_derive : Unable to derive IRQ for device 01:05.0
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi'
Starting kswapd
BIO: pool of 256 setup, 14Kb (56 bytes/bio)
biovec: init pool 0, 1 entries, 12 bytes
biovec: init pool 1, 4 entries, 48 bytes
biovec: init pool 2, 16 entries, 192 bytes
biovec: init pool 3, 64 entries, 768 bytes
biovec: init pool 4, 128 entries, 1536 bytes
biovec: init pool 5, 256 entries, 3072 bytes
Journalled Block Device driver loaded
NTFS driver 2.0.7 [Flags: R/O DEBUG]. Copyright (c) 2001,2002 Anton Altaparmakov.
udf: registering filesystem
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU1] (supports C1)
rivafb: RIVA MTRR set to ON
-----------------------------------------------------------
With "pci=noacpi" set:
Linux version 2.5.20 (root@turbulence.megapathdsl.net) (gcc version 3.0.4 (Red Hat Linux 7.2 3.0.4-1)) #22Video mode to be used for restore is f00
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000ffe0000 (usable)
BIOS-e820: 000000000ffe0000 - 000000000fff8000 (ACPI data)
BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65504
zone(0): 4096 pages.
zone(1): 61408 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 AMI ) @ 0x000fae70
ACPI: RSDT (v001 GATEWA 8DT-084 00529.06553) @ 0x0fff0000
ACPI: FADT (v001 GATEWA 8DT-084 00529.06553) @ 0x0fff1000
ACPI: MADT not present
Kernel command line: ro root=/dev/hda6 hdd=ide-scsi console=ttyS0,38400 console=tty0 pci=noacpi video=riva:1600x1200-16
ide_setup: hdd=ide-scsi
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 848.372 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1690.82 BogoMIPS
Memory: 255648k/262016k available (2231k kernel code, 5980k reserved, 566k data, 256k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Machine check exception polling timer started.
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Intel machine check reporting enabled on CPU#0.
WARNING: This combination of AMD processors is not suitable for SMP.
CPU0: AMD Athlon(tm) Processor stepping 01
per-CPU timeslice cutoff: 1462.63 usecs.
task migration cache decay timeout: 10 msecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 848.3206 MHz.
..... host bus clock speed is 199.6048 MHz.
cpu: 0, clocks: 1996048, slice: 998024
CPU0<T0:1996048,T1:998016,D:8,S:998024,C:1996048>
migration_task 0 on cpu=0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
PCI: PCI BIOS revision 2.10 entry at 0xfdad1, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20020517
tbxface-0100 [03] Acpi_load_tables : ACPI Tables successfully loaded
Parsing Methods:...................................................................................
Table [DSDT] - 271 Objects with 26 Devices 83 Methods 15 Regions
ACPI Namespace successfully loaded at root c0450d7c
evxfevnt-0076 [04] Acpi_enable : Transition to ACPI mode successful
Executing all Device _STA and_INI methods:............... exfldio-0098 [47] Ex_setup_region : Field) exfldio-0108 [47] Ex_setup_region : Field [PS2E] Base+Offset+Width 0+0+4 is beyond end of region [) uteval-0430 [34] Ut_execute_STA : No object was returned from _STA
...........
26 Devices found containing: 25 _STA, 2 _INI methods
Completing Region/Field/Buffer/Package initialization:..........................................
Initialized 12/15 Regions 1/1 Fields 21/21 Buffers 8/9 Packages (271 nodes)
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
exfldio-0098 [76] Ex_setup_region : Field [PS2E] access width (4 bytes) too large for region [PSRG) exfldio-0108 [76] Ex_setup_region : Field [PS2E] Base+Offset+Width 0+0+4 is beyond end of region [)pci_link-0152 [114] acpi_pci_link_get_poss: Resource is not an IRQ entry
pci_link-0152 [116] acpi_pci_link_get_poss: Resource is not an IRQ entry
pci_link-0152 [118] acpi_pci_link_get_poss: Resource is not an IRQ entry
pci_link-0152 [120] acpi_pci_link_get_poss: Resource is not an IRQ entry
PCI: Probing PCI hardware
Starting kswapd
BIO: pool of 256 setup, 14Kb (56 bytes/bio)
biovec: init pool 0, 1 entries, 12 bytes
biovec: init pool 1, 4 entries, 48 bytes
biovec: init pool 2, 16 entries, 192 bytes
biovec: init pool 3, 64 entries, 768 bytes
biovec: init pool 4, 128 entries, 1536 bytes
biovec: init pool 5, 256 entries, 3072 bytes
Journalled Block Device driver loaded
NTFS driver 2.0.7 [Flags: R/O DEBUG]. Copyright (c) 2001,2002 Anton Altaparmakov.
udf: registering filesystem
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU1] (supports C1)
rivafb: RIVA MTRR set to ON
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/