Andrew fix it: ethernet tulip misdetected starting 2.5.20

[Albert Cranford]

Andrew Morton already fixed it in pci device matching fix
Thanks,
Albert
http://marc.theaimsgroup.com/?l=linux-kernel&m=102315156003503&w=2
Albert Cranford wrote:
> 
> 2.5.19 works while 2.5.20 has mostly correct lspci output (PME- instead of PME+)
> but the wrong driver gets detected and fails loading.
> Similar to 3c509 vs 3c590 from Anton.
> Anyone have any ideas in troubleshooting this?
> Config:
> CONFIG_NET_TULIP=y
> # CONFIG_DE2104X is not set
> CONFIG_TULIP=m
> # CONFIG_TULIP_MWI is not set
> # CONFIG_TULIP_MMIO is not set
> # CONFIG_DE4X5 is not set
> 
>               linux-2.5.19
> dmesg
> Linux Tulip driver version 1.1.13 (May 11, 2002)
> PCI: Found IRQ 11 for device 00:0b.0
> eth0: ADMtek Comet rev 17 at 0xe800, 00:03:6D:16:4E:39, IRQ 11.
> 
> lspci -vv
> 00:0b.0 Ethernet controller: Bridgecom, Inc: Unknown device 0985 (rev 11)
>         Subsystem: Bridgecom, Inc: Unknown device 0574
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 255 min, 255 max, 32 set, cache line size 08
>         Interrupt: pin A routed to IRQ 11
>         Region 0: I/O ports at e800 [size=256]
>         Region 1: Memory at e3001000 (32-bit, non-prefetchable) [size=1K]
>         Expansion ROM at <unassigned> [disabled] [size=128K]
>         Capabilities: [c0] Power Management version 2
>                 Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME+
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME+
> 
> ------------------
>              linux-2.5.20
> dmesg
> Linux Tulip driver version 1.1.13 (May 11, 2002)
> PCI: Found IRQ 11 for device 00:0b.0
> tulip0:  MII transceiver #1 config 1000 status 786d advertising 01e1.
> eth0: Digital DS21140 Tulip rev 17 at 0xe800, EEPROM not present, 00:4C:69:6E:75:79, IRQ 11.
> 
> lspci -vv
> 00:0b.0 Ethernet controller: Bridgecom, Inc: Unknown device 0985 (rev 11)
>         Subsystem: Bridgecom, Inc: Unknown device 0574
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 255 min, 255 max, 32 set, cache line size 08
>         Interrupt: pin A routed to IRQ 11
>         Region 0: I/O ports at e800 [size=256]
>         Region 1: Memory at e3001000 (32-bit, non-prefetchable) [size=1K]
>         Expansion ROM at <unassigned> [disabled] [size=128K]
>         Capabilities: [c0] Power Management version 2
>                 Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME+
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> --
> Albert Cranford Deerfield Beach FL USA
> [e-mail]

-- 
Albert Cranford Deerfield Beach FL USA
[e-mail]