------*******-----
Linux version 2.4.19-pre8 (root@metalbox) (gcc version 2.95.4 20011002
(Debian prerelease)) #3 Tue May 14 11:56:35 EDT 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000017ff0000 (usable)
BIOS-e820: 0000000017ff0000 - 0000000017ff3000 (ACPI NVS)
BIOS-e820: 0000000017ff3000 - 0000000018000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
383MB LOWMEM available.
On node 0 totalpages: 98288
zone(0): 4096 pages.
zone(1): 94192 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=Linux ro root=303
Initializing CPU#0
Detected 1002.275 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1998.84 BogoMIPS
Memory: 386184k/393152k available (1435k kernel code, 6580k reserved, 455k
data, 232k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0383f9ff c1cbf9ff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After vendor init, caps: 0383f9ff c1cbf9ff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383f9ff c1cbf9ff 00000000 00000000
CPU: Common caps: 0383f9ff c1cbf9ff 00000000 00000000
CPU: AMD Duron(tm) processor stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb370, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router SIS [1039/0008] at 00:01.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
PCI: Found IRQ 9 for device 00:01.6
PCI: Sharing IRQ 9 with 00:0b.0
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller on PCI bus 00 dev 01
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later
SiS730
ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:DMA, hdd:pio
hda: FUJITSU MPG3307AT, ATA DISK drive
hdb: AOPEN CRW1232, ATAPI CD/DVD-ROM drive
hdc: TOSHIBA DVD-ROM SD-M1502, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 60046560 sectors (30744 MB) w/2048KiB Cache, CHS=3971/240/63, UDMA(100)
hdb: ATAPI 32X CD-ROM CD-R/RW drive, 4096kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
hdc: ATAPI 48X DVD-ROM drive, 128kB Cache, UDMA(33)
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
8139too Fast Ethernet driver 0.9.24
PCI: Found IRQ 5 for device 00:09.0
eth0: SMC1211TX EZCard 10/100 (RealTek RTL8139) at 0xd8800000,
00:e0:29:94:ca:bc, IRQ 5
eth0: Identified 8139 chip type 'RTL-8139C'
PCI: Found IRQ 11 for device 00:0d.0
PCI: Sharing IRQ 11 with 00:01.2
PCI: Sharing IRQ 11 with 00:01.3
eth1: RealTek RTL8139 Fast Ethernet at 0xd8802000, 00:07:95:ad:61:d6, IRQ 11
eth1: Identified 8139 chip type 'RTL-8139C'
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 321M
agpgart: Detected SiS 730 chipset
agpgart: AGP aperture is 64M @ 0xd8000000
[drm] Initialized tdfx 1.0.0 20010216 on minor 0
[drm] AGP 0.99 on SiS @ 0xd8000000 64MB
[drm] Initialized radeon 1.1.1 20010405 on minor 1
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Creative EMU10K1 PCI Audio Driver, version 0.18, 11:58:56 May 14 2002
PCI: Found IRQ 9 for device 00:0b.0
PCI: Sharing IRQ 9 with 00:01.6
emu10k1: EMU10K1 rev 8 model 0x8027 found, IO at 0xdc00-0xdc1f, IRQ 9
ac97_codec: AC97 codec, id: 0x5452:0x4123 (TriTech TR A5)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
ds: no socket drivers loaded!
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 232k freed
Adding Swap: 506480k swap-space (priority -1)
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hdb: DMA disabled
ide0: reset: success
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
_______*******_______
Heres the ifconfig before pinging:
_______*******_______
eth0 Link encap:Ethernet HWaddr 00:E0:29:94:CA:BC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:2052 (2.0 KiB)
Interrupt:5
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:560 (560.0 b) TX bytes:560 (560.0 b)
___________**************___________
Then i tried to ping 192.168.0.1 (My Firewall/DHCP Server)
then ran ifconfig again
__________************__________
eth0 Link encap:Ethernet HWaddr 00:E0:29:94:CA:BC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:2052 (2.0 KiB)
Interrupt:5
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:560 (560.0 b) TX bytes:560 (560.0 b)
______________***************___________
Heres the dmesg from the 2.2.20 kernel just for reference
_______________*************______________
Linux version 2.2.20 (herbert@gondolin) (gcc version 2.7.2.3) #1 Mon Dec 31
07:05:08 EST 2001
BIOS-provided physical RAM map:
BIOS-e820: 0009f000 @ 00000000 (usable)
BIOS-e820: 17ef0000 @ 00100000 (usable)
Detected 1002293 kHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1998.84 BogoMIPS
Memory: 386576k/393152k available (1756k kernel code, 412k reserved, 4256k
data, 152k init)
Dentry hash table entries: 65536 (order 7, 512k)
Buffer cache hash table entries: 524288 (order 9, 2048k)
Page cache hash table entries: 131072 (order 7, 512k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: L1 I Cache: 64K L1 D Cache: 64K
CPU: L2 Cache: 64K
CPU: AMD Duron(tm) processor stepping 01
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xfb370
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 524288 bhash 65536)
Starting kswapd v 1.5
Serial driver version 4.27 with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
loop: registered device at major 7
SIS5513: IDE controller on PCI bus 00 dev 01
SIS5513: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:DMA, hdd:pio
hda: FUJITSU MPG3307AT, ATA DISK drive
hdb: AOPEN CRW1232, ATAPI CDROM drive
hdc: TOSHIBA DVD-ROM SD-M1502, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: FUJITSU MPG3307AT, 29319MB w/2048kB Cache, CHS=3971/240/63
hdb: ATAPI 32X CD-ROM CD-R/RW drive, 4096kB Cache
Uniform CD-ROM driver Revision: 3.11
hdc: ATAPI 48X DVD-ROM drive, 128kB Cache
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
scsi: <fdomain> Detection failed (no card)
NCR53c406a: no available ports found
sym53c416.c: Version 1.0.0
Failed initialization of WD-7000 SCSI card!
IBM MCA SCSI: Version 3.2
IBM MCA SCSI: No Microchannel-bus present --> Aborting.
This machine does not have any IBM MCA-bus
or the MCA-Kernel-support is not enabled!
megaraid: v1.11 (Aug 23, 2000)
aec671x_detect:
3ware Storage Controller device driver for Linux v1.02.00.008.
3w-xxxx: tw_findcards(): No cards found.
scsi : 0 hosts.
scsi : detected total.
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 >
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.13)
apm: disabled on user request.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 152k freed
NET4: Unix domain sockets 1.0 for Linux NET4.0.
Adding Swap: 506480k swap-space (priority -1)
eth0: 8139too Fast Ethernet driver 0.9.18-pre4 Jeff Garzik
<jgarzik@mandrakesoft.com>
eth0: Linux-2.2 bug reports to Jens David <dg1kjd@afthd.tu-darmstadt.de>
eth0: RealTek RTL8139 Fast Ethernet board found at 0xd8050000, IRQ 11
eth0: Chip is 'RTL-8139C' - MAC address '00:07:95:ad:61:d6'.
eth1: SMC1211TX EZCard 10/100 (RealTek RTL8139) board found at 0xd8052000,
IRQ 5
eth1: Chip is 'RTL-8139C' - MAC address '00:e0:29:94:ca:bc'.
Creative EMU10K1 PCI Audio Driver, version 0.7, 07:13:36 Dec 31 2001
emu10k1: EMU10K1 rev 8 model 0x8027 found, IO at 0xdc00-0xdc1f, IRQ 9
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability
41e1.
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability
41e1.
__________**********___________
I also noticed that when booting, the 2.2.20 kernel identifies media type
100MBit Full duplex, and under 2.4.19-pre8 it detects 10MBit half duplex.,
if that makes a difference
----- Original Message -----
From: "bert hubert" <ahu@ds9a.nl>
To: "Andre LeBlanc" <ap.leblanc@shaw.ca>
Cc: <linux-kernel@vger.kernel.org>
Sent: Tuesday, May 14, 2002 1:29 PM
Subject: Re: No Network after Compiling, 2.4.19-pre8 under Debian Woody
> On Tue, May 14, 2002 at 04:15:14PM -0700, Andre LeBlanc wrote:
> > Ok, the system is a Duron 1GHz on an ECS Motherboard with the SiS 730S
> > Chipset. 384 MB PC133, with a realtek 8139 based Nic.
> > heres the .config
> >
> > network works fine if I boot the old(2.2.20) kernel but booting
2.4.19-pre8
> > causes me to have no network connection, But the device is configured
> > properly. (I Think)
> > I can also send my dmesg if it will help
>
> Please do. Also show the output of ifconfig before and after trying to
ping
> some hosts.
>
> --
> http://www.PowerDNS.com Versatile DNS Software & Services
> http://www.tk the dot in .tk
> http://lartc.org Linux Advanced Routing & Traffic Control HOWTO
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/