Got this error
hdi: timeout waiting for DMA
hdi: ide_dma_timeout: Lets do it again!stat = 0x58, dma_stat = 0x20
hdi: DMA disabled
hdi: irq timeout: status=0xd0 { Busy }
hdi: DMA disabled
hdi: ide_set_handler: handler not null; old=c019c89c, new=c019c89c
bug: kernel timer added twice at c019c73e.
ide4: reset: success
during I/O testing on a RAID0 set but no freeze, crash or oops.
Hopefully there are not SMP spinlock problems still hanging around.
I am willing to do specific testing if requested. Machine data below.
Also note CPU ID reporting changed from 2.2.20 as this board
has always running PGA370 Celeron 533's which used to be correctly
identified "Intel Celeron (Mendocino) stepping 05" and are now
incorrectly identified "Intel Mobile Pentium II stepping 05".
...
***************
*** 52,58 ****
smp kernel: mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
! smp kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
! smp kernel: CPU: L2 cache: 128K
smp kernel: Intel machine check reporting enabled on CPU#0.
smp kernel: per-CPU timeslice cutoff: 25.02 usecs.
! smp kernel: CPU0: Intel Mobile Pentium II stepping 05
smp kernel: Getting VERSION: 40011
--- 49,56 ----
smp kernel: mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
! smp kernel: Intel machine check architecture supported.
smp kernel: Intel machine check reporting enabled on CPU#0.
+ smp kernel: 128K L2 cache (4 way)
+ smp kernel: CPU: L2 Cache: 128K
smp kernel: per-CPU timeslice cutoff: 25.02 usecs.
! smp kernel: CPU0: Intel Celeron (Mendocino) stepping 05
smp kernel: Getting VERSION: 40011
Abit BP6 gets my vote for most interesting motherboard in history. Please
let me know if there's any other info needed.
rgds,
tim.
[tim@smp src]# hdparm -iv /dev/hdi
/dev/hdi:
multcount = 0 (off)
I/O support = 0 (default 16-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 1 (on)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 1027/255/63, sectors = 16514064, start = 0
Model=FUJITSU MPE3084AE, FwRev=EE-C0-24, SerialNo=05341919
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=512kB, MaxMultSect=16, MultSect=off
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=16514064
IORDY=yes, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
[tim@smp src]# lspci -vvv
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 32 set
Region 0: Memory at da000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d8000000-d9ffffff
Prefetchable memory behind bridge: d0000000-d7ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00:07.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set
Region 4: I/O ports at f000
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set
Interrupt: pin D routed to IRQ 0
Region 4: I/O ports at 9000
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:0d.0 Unknown mass storage controller: Promise Technology, Inc. 20262 (rev 01)
Subsystem: Promise Technology, Inc.: Unknown device 4d33
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 9400
Region 1: I/O ports at 9800
Region 2: I/O ports at 9c00
Region 3: I/O ports at a000
Region 4: I/O ports at a400
Region 5: Memory at dd000000 (32-bit, non-prefetchable)
Capabilities: [58] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.0 Ethernet controller: Lite-On Communications Inc LNE100TX (rev 20)
Subsystem: Netgear FA310TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at a800
Region 1: Memory at dd020000 (32-bit, non-prefetchable)
00:13.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 (rev 01)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 8 min, 8 max, 120 set, cache line size 08
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at ac00
Region 1: I/O ports at b000
Region 4: I/O ports at b400
00:13.1 Unknown mass storage controller: Triones Technologies, Inc. HPT366 (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 8 min, 8 max, 120 set, cache line size 08
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at b800
Region 1: I/O ports at bc00
Region 4: I/O ports at c000
01:00.0 VGA compatible controller: S3 Inc. Savage 4 (rev 02) (prog-if 00 [VGA])
Subsystem: S3 Inc.: Unknown device 8a22
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 4 min, 255 max, 248 set, cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d9000000 (32-bit, non-prefetchable)
Region 1: Memory at d0000000 (32-bit, prefetchable)
Capabilities: [dc] Power Management version 1
Flags: PMEClk- AuxPwr- DSI+ D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
smp syslogd 1.3-3: restart.
smp syslog: syslogd startup succeeded
smp kernel: klogd 1.3-3, log source = /proc/kmsg started.
smp kernel: Inspecting /boot/System.map
smp syslog: klogd startup succeeded
smp kernel: Loaded 8104 symbols from /boot/System.map.
smp kernel: Symbols match kernel version 2.2.21.
smp kernel: No module symbols loaded.
smp kernel: Linux version 2.2.21pre2-iOR (root@smp) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #8 SMP Sun Jan 27 1
smp kernel: BIOS-provided physical RAM map:
smp kernel: BIOS-e820: 0009e000 @ 00000000 (usable)
smp kernel: BIOS-e820: 0ff00000 @ 00100000 (usable)
smp kernel: Scan SMP from c0000000 for 1024 bytes.
smp kernel: Scan SMP from c009fc00 for 1024 bytes.
smp kernel: Scan SMP from c00f0000 for 65536 bytes.
smp kernel: Intel MultiProcessor Specification v1.4
smp kernel: Virtual Wire compatibility mode.
smp kernel: OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
smp kernel: Processor #0 Pentium(tm) Pro APIC version 17
smp kernel: Floating point unit present.
smp kernel: Machine Exception supported.
smp kernel: 64 bit compare & exchange supported.
smp kernel: Internal APIC present.
smp kernel: Bootup CPU
smp kernel: Processor #1 Pentium(tm) Pro APIC version 17
smp kernel: Floating point unit present.
smp kernel: Machine Exception supported.
smp kernel: 64 bit compare & exchange supported.
smp kernel: Internal APIC present.
smp kernel: Bus #0 is PCI
smp kernel: Bus #1 is PCI
smp kernel: Bus #2 is ISA
smp kernel: I/O APIC #2 Version 17 at 0xFEC00000.
smp kernel: Processors: 2
smp kernel: mapped APIC to ffffe000 (fee00000)
smp kernel: mapped IOAPIC to ffffd000 (fec00000)
smp kernel: Detected 575919 kHz processor.
smp kernel: ide_setup: idebus=36
smp kernel: Console: colour VGA+ 80x25
smp kernel: Calibrating delay loop... 1150.15 BogoMIPS
smp kernel: Memory: 257336k/262144k available (1304k kernel code, 424k reserved, 3000k data, 80k init)
smp kernel: Dentry hash table entries: 32768 (order 6, 256k)
smp kernel: Buffer cache hash table entries: 262144 (order 8, 1024k)
smp kernel: Page cache hash table entries: 65536 (order 6, 256k)
smp kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
smp kernel: CPU: L2 cache: 128K
smp kernel: Intel machine check architecture supported.
smp kernel: Intel machine check reporting enabled on CPU#0.
smp kernel: Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
smp kernel: Checking 'hlt' instruction... OK.
smp kernel: POSIX conformance testing by UNIFIX
smp kernel: mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
smp kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
smp kernel: CPU: L2 cache: 128K
smp kernel: Intel machine check reporting enabled on CPU#0.
smp kernel: per-CPU timeslice cutoff: 25.02 usecs.
smp kernel: CPU0: Intel Mobile Pentium II stepping 05
smp kernel: Getting VERSION: 40011
smp kernel: Getting VERSION: 40011
smp kernel: Getting LVT0: 700
smp kernel: Getting LVT1: 400
smp kernel: setup_APIC_clock() called.
smp kernel: calibrating APIC timer ...
smp kernel: ..... 5759061 CPU clocks in 1 timer chip tick.
smp kernel: ..... 719881 APIC bus clocks in 1 timer chip tick.
smp kernel: ..... CPU clock speed is 575.9061 MHz.
smp kernel: ..... system bus clock speed is 71.9881 MHz.
smp kernel: CPU map: 3
smp kernel: Booting processor 1 eip 2000
smp kernel: Setting warm reset code and vector.
smp kernel: 1.
smp kernel: 2.
smp kernel: 3.
smp kernel: Asserting INIT.
smp kernel: Deasserting INIT.
smp kernel: Sending STARTUP #1.
smp kernel: After apic_write.
smp kernel: Before start apic_write.
smp kernel: Startup point 1.
smp kernel: CPU#1 waiting for CALLOUT
smp kernel: Waiting for send to finish...
smp kernel: +Sending STARTUP #2.
smp kernel: After apic_write.
smp kernel: Before start apic_write.
smp kernel: Startup point 1.
smp kernel: Waiting for send to finish...
smp kernel: +After Startup.
smp kernel: Before Callout 1.
smp kernel: After Callout 1.
smp kernel: CALLIN, before enable_local_APIC().
smp kernel: setup_APIC_clock() called.
smp kernel: waiting for other CPU calibrating APIC ... done, continuing.
smp kernel: Calibrating delay loop... 1150.15 BogoMIPS
smp kernel: Stack at about cfffbfbc
smp kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
smp kernel: CPU: L2 cache: 128K
smp kernel: Intel machine check reporting enabled on CPU#1.
smp kernel: OK.
smp kernel: CPU1: Intel Mobile Pentium II stepping 05
smp kernel: CPU has booted.
smp kernel: Before bogomips.
smp kernel: Total of 2 processors activated (2300.31 BogoMIPS).
smp kernel: Before bogocount - setting activated=1.
smp kernel: Boot done.
smp kernel: enabling symmetric IO mode... ...done.
smp kernel: ENABLING IO-APIC IRQs
smp kernel: init IO_APIC IRQs
smp kernel: IO-APIC (apicid-pin) 2-0, 2-7, 2-10, 2-11, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
smp kernel: number of MP IRQ sources: 19.
smp kernel: number of IO-APIC #2 registers: 24.
smp kernel: testing the IO APIC.......................
smp kernel:
smp kernel: IO APIC #2......
smp kernel: .... register #00: 02000000
smp kernel: ....... : physical APIC id: 02
smp kernel: .... register #01: 00170011
smp kernel: ....... : max redirection entries: 0017
smp kernel: ....... : IO APIC version: 0011
smp kernel: .... register #02: 00000000
smp kernel: ....... : arbitration: 00
smp kernel: .... IRQ redirection table:
smp kernel: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
smp kernel: 00 000 00 1 0 0 0 0 0 0 00
smp kernel: 01 0FF 0F 1 0 0 0 0 1 1 59
smp kernel: 02 0FF 0F 0 0 0 0 0 1 1 51
smp kernel: 03 0FF 0F 1 0 0 0 0 1 1 61
smp kernel: 04 0FF 0F 1 0 0 0 0 1 1 69
smp kernel: 05 0FF 0F 1 0 0 0 0 1 1 71
smp kernel: 06 0FF 0F 1 0 0 0 0 1 1 79
smp kernel: 07 000 00 1 0 0 0 0 0 0 00
smp kernel: 08 0FF 0F 1 0 0 0 0 1 1 81
smp kernel: 09 0FF 0F 1 0 0 0 0 1 1 89
smp kernel: 0a 000 00 1 0 0 0 0 0 0 00
smp kernel: 0b 000 00 1 0 0 0 0 0 0 00
smp kernel: 0c 0FF 0F 1 0 0 0 0 1 1 91
smp kernel: 0d 000 00 1 0 0 0 0 0 0 00
smp kernel: 0e 0FF 0F 1 0 0 0 0 1 1 99
smp kernel: 0f 0FF 0F 1 0 0 0 0 1 1 A1
smp kernel: 10 0FF 0F 1 1 0 1 0 1 1 A9
smp kernel: 11 0FF 0F 1 1 0 1 0 1 1 B1
smp kernel: 12 0FF 0F 1 1 0 1 0 1 1 B9
smp kernel: 13 000 00 1 0 0 0 0 0 0 00
smp kernel: 14 000 00 1 0 0 0 0 0 0 00
smp kernel: 15 000 00 1 0 0 0 0 0 0 00
smp kernel: 16 000 00 1 0 0 0 0 0 0 00
smp kernel: 17 000 00 1 0 0 0 0 0 0 00
smp nscd: nscd startup succeeded
smp kernel: .................................... done.
smp kernel: checking TSC synchronization across CPUs: passed.
smp kernel: Setting commenced=1, go go go
smp kernel: mtrr: your CPUs had inconsistent fixed MTRR settings
smp kernel: mtrr: probably your BIOS does not setup all CPUs
smp kernel: PCI: Using configuration type 1
smp kernel: PCI: Probing PCI hardware
smp kernel: PCI->APIC IRQ transform: (B0,I13,P0) -> 17
smp kernel: PCI->APIC IRQ transform: (B0,I15,P0) -> 16
smp kernel: PCI->APIC IRQ transform: (B0,I19,P0) -> 18
smp kernel: PCI->APIC IRQ transform: (B0,I19,P1) -> 18
smp kernel: PCI->APIC IRQ transform: (B1,I0,P0) -> 16
smp kernel: Linux NET4.0 for Linux 2.2
smp kernel: Based upon Swansea University Computer Society NET3.039
smp kernel: NET4: Unix domain sockets 1.0 for Linux NET4.0.
smp kernel: NET4: Linux TCP/IP 1.0 for NET4.0
smp kernel: IP Protocols: ICMP, UDP, TCP
smp kernel: TCP: Hash tables configured (ehash 262144 bhash 65536)
smp kernel: Starting kswapd v 1.5
smp kernel: Detected PS/2 Mouse Port.
smp kernel: Serial driver version 4.27 with no serial options enabled
smp kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
smp kernel: Real Time Clock Driver v1.09
smp kernel: loop: registered device at major 7
smp kernel: Uniform Multi-Platform E-IDE driver Revision: 6.30
smp kernel: ide: Assuming 36MHz system bus speed for PIO modes
smp kernel: PIIX4: IDE controller on PCI bus 00 dev 39
smp kernel: PIIX4: chipset revision 1
smp kernel: PIIX4: not 100% native mode: will probe irqs later
smp kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
smp kernel: PDC20262: IDE controller on PCI bus 00 dev 68
smp kernel: PDC20262: chipset revision 1
smp kernel: PDC20262: not 100% native mode: will probe irqs later
smp kernel: PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
smp kernel: ide2: BM-DMA at 0xa400-0xa407, BIOS settings: hde:DMA, hdf:DMA
smp kernel: ide3: BM-DMA at 0xa408-0xa40f, BIOS settings: hdg:DMA, hdh:pio
smp kernel: HPT366: onboard version of chipset, pin1=1 pin2=2
smp kernel: PCI: HPT366: Fixing interrupt 18 pin 2 to ZERO
smp kernel: HPT366: IDE controller on PCI bus 00 dev 98
smp kernel: HPT366: chipset revision 1
smp rc.sysinit: Mounting proc filesystem succeeded
smp kernel: HPT366: not 100% native mode: will probe irqs later
smp sysctl: net.ipv4.ip_forward = 0
smp kernel: ide1: BM-DMA at 0xb400-0xb407, BIOS settings: hdc:pio, hdd:pio
smp sysctl: net.ipv4.conf.all.rp_filter = 1
smp sysctl: net.ipv4.ip_always_defrag = 0
smp sysctl: kernel.sysrq = 0
smp rc.sysinit: Configuring kernel parameters succeeded
smp date: Sun Jan 27 19:43:16 PST 2002
smp rc.sysinit: Setting clock : Sun Jan 27 19:43:16 PST 2002 succeeded
smp kernel: HPT366: IDE controller on PCI bus 00 dev 99
smp kernel: HPT366: chipset revision 1
smp kernel: HPT366: not 100% native mode: will probe irqs later
smp kernel: ide4: BM-DMA at 0xc000-0xc007, BIOS settings: hdi:pio, hdj:pio
smp kernel: hda: FUJITSU MPD3084AT, ATA DISK drive
smp kernel: hdc: FUJITSU MPE3084AE, ATA DISK drive
smp kernel: hde: IBM-DTLA-307020, ATA DISK drive
smp kernel: hdg: IBM-DTLA-307020, ATA DISK drive
smp kernel: hdi: FUJITSU MPE3084AE, ATA DISK drive
smp kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
smp kernel: ide1 at 0xac00-0xac07,0xb002 on irq 18
smp kernel: ide2 at 0x9400-0x9407,0x9802 on irq 17
smp kernel: ide3 at 0x9c00-0x9c07,0xa002 on irq 17
smp kernel: ide4 at 0xb800-0xb807,0xbc02 on irq 18
smp kernel: hda: FUJITSU MPD3084AT, 8063MB w/512kB Cache, CHS=1027/255/63, UDMA(33)
smp kernel: hdc: FUJITSU MPE3084AE, 8063MB w/512kB Cache, CHS=16383/16/63, UDMA(33)
smp kernel: hde: IBM-DTLA-307020, 19623MB w/1916kB Cache, CHS=39870/16/63, UDMA(66)
smp kernel: hdg: IBM-DTLA-307020, 19623MB w/1916kB Cache, CHS=39870/16/63, UDMA(66)
smp kernel: hdi: FUJITSU MPE3084AE, 8063MB w/512kB Cache, CHS=16383/16/63, UDMA(33)
smp kernel: Floppy drive(s): fd0 is 1.44M
smp kernel: FDC 0 is a post-1991 82077
smp kernel: md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
smp kernel: raid0 personality registered
smp kernel: 3ware Storage Controller device driver for Linux v1.02.00.010.
smp kernel: 3w-xxxx: tw_findcards(): No cards found.
smp kernel: scsi0 : SCSI host adapter emulation for IDE ATAPI devices
smp kernel: scsi : 1 host.
smp kernel: scsi : detected total.
smp kernel: tulip.c:v0.91g-ppc 7/16/99 becker@cesdis.gsfc.nasa.gov
smp kernel: eth0: Lite-On 82c168 PNIC rev 32 at 0xa800, 00:A0:CC:58:BD:19, IRQ 16.
smp kernel: eth0: MII transceiver #1 config 3000 status 7829 advertising 01e1.
smp kernel: md.c: sizeof(mdp_super_t) = 4096
smp kernel: Partition check:
smp kernel: hda: hda1 hda2 hda3 hda4
smp kernel: hdc: [PTBL] [1027/255/63] hdc1 hdc2
smp kernel: hde: [PTBL] [2501/255/63] hde1 hde2 hde3
smp kernel: hdg: [PTBL] [2501/255/63] hdg1 hdg2 hdg3
smp kernel: hdi: [PTBL] [1027/255/63] hdi1 hdi2
smp kernel: VFS: Mounted root (ext2 filesystem) readonly.
smp kernel: Freeing unused kernel memory: 80k freed
smp kernel: Adding Swap: 257032k swap-space (priority 1)
-- - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/