Re: SiS900 driver after v.1.07.11 (==Linux 2.4.5) won't allow connect.

[Rune Petersen]

try a temp. solution,
but keep trying to get this fixed

copy the last drivers from the kernel that works into the new kernel tree.
that's what I do, because the drivers (kernel 2.4.4+) is incompatible with
my switch

Rune Petersen
----- Original Message -----
From: Mike <[e-mail]>
To: LKML <[e-mail]>
Cc: <[e-mail]>; Jeff Garzik <[e-mail]>
Sent: Tuesday, January 08, 2002 8:21 AM
Subject: Re: SiS900 driver after v.1.07.11 (==Linux 2.4.5) won't allow
connect.

> Darn, same problem as before; it gives me "Media Link ON 10mbps
half-duplex"
> but now atleast dhcpcd doesn't fail.
> What's worse: I pinged my nameserver across the street and lost 10% of 19
> pings. Dunno if "half-baked-duplex" is what does that...but I'm still
forced
> to use 2.4.5 for now. :'-(
>
>
> I wrote:
>
> > Heh, just read about the 2.4.18pre1 sis900 patch, I wonder if that'll be
> > what it takes...I'm compiling it now.
> > Will reply with results.
> > Gtreets, Mike
> >
> > I wrote:
> >
> > > Hello,
> > >
> > > I've got this weird problem, I know the problem is mine 'cuz the
latest
> > > in 2.4.17 doesn't work either, and I don't think Linus would keep a
bad
> > > copy of widely-used code in his kernel, right?  ;-)
> > > Anyway, the hardware in question is an ECS K7S5A motherboard with a
> > > SiS735 chipset and on-board LAN. The only Realtek chip I see on the
> > > mainboard is one marked "RTL8201L".
> > >
> > > WHAT HAPPENS WHEN IT WORKS (flawlessly):
> > > With a modular kernel 2.4.5 I simply 'modprobe sis900' and presto...I
> > > follow that with 'dhcpcd' and I'm on the 'net. Here's what syslog
says:
> > > SiS900.c: v.1.07.11 4/10/2001
> > > PCI: Assigned IRQ3 for device 00:03.0
> > > eth0: Unknown PHY transceiver found at address 1 <<<-------!!!!
> > > eth0: Using transceiver found at address1 as default
> > > eth0: SiS900 PCI Fast Ethernet at 0xdc00, IRQ3, <MAC-address here>
> > > logger: (dhcpcd) IP changed to <IP-address here>
> > >
> > > WHAT HAPPENS WHEN IT FAILS:
> > > With a modular kernel 2.4.6 or 2.4.13 or 2.4.17 I 'modprobe sis900'
and
> > > get:
> > > SiS900.c: v.1.08.01 9/25/2001 <<<--------Some kernels differ
accordingly
> > > in version and date. All >=1.08 fail.
> > > PCI: Assigned IRQ3 for device 00:03.0
> > > eth0: Realtek RTL8201 PHY transceiver found at address 1
> > > eth0: Using transceiver found at address1 as default
> > > eth0: SiS900 PCI Fast Ethernet at 0xdc00, IRQ3, <MAC-address here>
> > >
> > > I follow this with 'dhcpcd' and syslog says:
> > > Media Link ON 10mbps half-duplex
> > > ....And my prompt hangs there until dhcpcd time-outs after 3 or 5
> > > minutes...
> > >
> > > What am I missing here? Should I add some stuff to the 'modprobe
sis900'
> > > string now??
> > > And yeah, I've read all the relevant (?!) docs in the kernel sources.
> > > Also, linux-2.4.17/Documentation/networking/sis900.txt only goes up to
> > > v.1.07, shouldn't it reflect the current revision (1.08.01)??
> > >
> > > I hope it's possible to just copy the old 2.4.5 source into the 2.4.17
> > > dir (as you can tell: I've never done this) and compile.
> > > TIA for any help and greets!
> > > -Mike
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [e-mail]
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/