usb.c: unable to get major 180 for usb devices
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.268 $ time 13:10:52 Jan 7 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: kmalloc IF c4b76e80, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI Root Hub
SerialNumber: d000
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface c4b76e80
usb.c: kusbd: /sbin/hotplug add 1
usb.c: kusbd policy returned 0xfffffffe
usb-uhci.c: USB UHCI at I/O 0xcc00, IRQ 10
usb-uhci.c: Detected 2 ports
hub.c: port 1 connection change
hub.c: port 1, portstatus 100, change 3, 12 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 100, change 3, 12 Mb/s
hub.c: port 1 enable change, status 100
hub.c: port 2 enable change, status 100
usb.c: new USB bus registered, assigned bus number 2
usb.c: kmalloc IF c4b76c80, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI Root Hub
SerialNumber: cc00
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface c4b76c80
usb.c: kusbd: /sbin/hotplug add 1
usb.c: kusbd policy returned 0xfffffffe
usb-uhci.c: USB UHCI at I/O 0xc800, IRQ 10
usb-uhci.c: Detected 2 ports
hub.c: port 1 connection change
hub.c: port 1, portstatus 100, change 3, 12 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 101, change 3, 12 Mb/s
hub.c: port 2, portstatus 103, change 0, 12 Mb/s
hub.c: USB new device connect on bus2/2, assigned device number 2
usb.c: new USB bus registered, assigned bus number 3
usb.c: kmalloc IF c4b76ac0, numif 1
usb.c: new device strings: Mfr=0, Product=1, SerialNumber=0
usb.c: kmalloc IF c4b76980, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI Root Hub
SerialNumber: c800
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: USB device number 2 default language ID 0x409
Product: USB Host To Host Bridge
usb.c: unhandled interfaces on device
usb.c: USB device 2 (vend/prod 0x5e3/0x502) is not claimed by any active
driver.
Length = 18
DescriptorType = 01
USB version = 1.00
Vendor:Product = 05e3:0502
MaxPacketSize0 = 8
NumConfigurations = 1
Device version = 1.80
Device Class:SubClass:Protocol = 00:00:00
Per-interface classes
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 0027
bNumInterfaces = 01
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = 80
MaxPower = 8mA
Interface: 0
Alternate Setting: 0
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 00
bNumEndpoints = 03
bInterface Class:SubClass:Protocol = ff:00:00
iInterface = 01
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0040
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 02 (out)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0040
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 83 (in)
bmAttributes = 03 (Interrupt)
wMaxPacketSize = 0008
bInterval = 10
usb.c: kusbd: /sbin/hotplug add 2
usb.c: kusbd policy returned 0xfffffffe
hub.c: port 1 enable change, status 100
usb.c: hub driver claimed interface c4b76980
usb.c: kusbd: /sbin/hotplug add 1
usb.c: kusbd policy returned 0xfffffffe
usb-uhci.c: v1.268:USB Universal Host Controller Interface driver
hub.c: port 1 connection change
hub.c: port 1, portstatus 100, change 3, 12 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 101, change 3, 12 Mb/s
hub.c: port 2, portstatus 103, change 0, 12 Mb/s
hub.c: USB new device connect on bus3/2, assigned device number 2
usb.c: kmalloc IF c4b76880, numif 1
usb.c: new device strings: Mfr=1, Product=1, SerialNumber=0
usb.c: USB device number 2 default language ID 0x409
Manufacturer: ScanLogic USBIDE
Product: ScanLogic USBIDE
usb.c: unhandled interfaces on device
usb.c: USB device 2 (vend/prod 0x4ce/0x2) is not claimed by any active driver.
Length = 18
DescriptorType = 01
USB version = 1.10
Vendor:Product = 04ce:0002
MaxPacketSize0 = 8
NumConfigurations = 1
Device version = 2.60
Device Class:SubClass:Protocol = 00:00:00
Per-interface classes
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 0020
bNumInterfaces = 01
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = 40
MaxPower = 0mA
Interface: 0
Alternate Setting: 0
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 00
bNumEndpoints = 02
bInterface Class:SubClass:Protocol = 08:06:50
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 02 (out)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0040
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0040
bInterval = 00
usb.c: kusbd: /sbin/hotplug add 2
usb.c: kusbd policy returned 0xfffffffe
hub.c: port 1 enable change, status 100
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
usb-storage: act_altsettting is 0
usb-storage: id_index calculated to be: 52
usb-storage: Array length appears to be: 54
usb-storage: USB Mass Storage device detected
usb-storage: Endpoints: In: 0xcff64154 Out: 0xcff64140 Int: 0x00000000
(Period 0)
usb-storage: New GUID 04ce00020000000000000000
usb-storage: GetMaxLUN command result is 1, data is 0
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: *** thread sleeping.
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 ff 00 00 00 75 04 1a c0
usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 255 F 128 CL 6
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 255 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 255/255
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x600350 R 159 Stat 0x0
usb-storage: Bulk logical error
usb-storage: Bulk reset requested
and more.... :
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=c800
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=04ce ProdID=0002 Rev= 2.60
S: Manufacturer=ScanLogic USBIDE
S: Product=ScanLogic USBIDE
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=cc00
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=05e3 ProdID=0502 Rev= 1.80
S: Product=USB Host To Host Bridge
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 8mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl= 16ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=d000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/