I am experiencing problems using a 3Com Network card and Adaptec SCSI
card under 2.4.17 in SMP mode. Since the only other PCI card in my system
is a very under used sound card I am wondering if this is a deeper
problem with SMP under Linux on my system.
I recently installed two Intel P3 Coppermine processors onto my Abit
VP6 motherboard and recompiled my kernel as SMP. I am seeing
problems that never once occured during the month I ran the system
with one P3 processor in UP mode.
During light network load I am seeing messages appear frequently in the
kernel messages and the network card stop receiving/transmitting traffic
out onto the network. This did not happen (and does not happen) when
running Uni-processor:
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
diagnostics: net 0c80 media 88c0 dma ffffffff.
eth0: Updating statistics failed, disabling stats as an interrupt source.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
diagnostics: net 0c80 media 88c0 dma ffffffff.
Also I am seeing problems with the SCSI system:
scsi0: PCI error Interrupt at seqaddr = 0x8
scsi0: Data Parity Error Detected during address or write data phase
I have to devices on the SCSI bus: Yamaha 2100S scsi CDRW and a HP DDS3
DAT tape drive. Again, I have had no problems with these devices prior to
running with SMP.
I've included a rundown of the hard I'm using and some stats:
ABIT VP6 Dual intel Motherboard
VIA VT82C686 Chipset
2x 1Ghz PIII Coppermine
512 Mb Ram
3Com 3c595 100baseT NIC
Adaptec 29160N SCSI card
Creative SB512 sound card ( Ensoniq 5880 AudioPCI )
Matrox G200 AGP graphics card
Slackware 8.0 with 2.4.17
#lspci -vv
00:00.0 Host bridge: VIA Technologies, Inc. VT82C691 [Apollo PRO] (rev c4)
Subsystem: ABIT Computer Corp.: Unknown device a204
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d4000000-d6ffffff
Prefetchable memory behind bridge: d7000000-d7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super] (rev 40)
Subsystem: ABIT Computer Corp.: Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586 IDE [Apollo]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at d000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at d800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 02)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI128
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at dc00 [size=64]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 SCSI storage controller: Adaptec 7892A (rev 02)
Subsystem: Adaptec: Unknown device 62a0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (10000ns min, 6250ns max), cache line size 08
Interrupt: pin A routed to IRQ 17
BIST result: 00
Region 0: I/O ports at e000 [disabled] [size=256]
Region 1: Memory at d9000000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 Ethernet controller: 3Com Corporation 3c595 100BaseTX [Vortex]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (750ns min, 2000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at e400 [size=32]
Expansion ROM at <unassigned> [disabled] [size=64K]
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP (rev 01) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G200 AGP
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d7000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at d4000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at d5000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x2
#cat /proc/interrupts
CPU0 CPU1
0: 189811 129350 IO-APIC-edge timer
1: 2 0 IO-APIC-edge keyboard
2: 0 0 XT-PIC cascade
8: 1 0 IO-APIC-edge rtc
14: 2384 2334 IO-APIC-edge ide0
15: 5523 4584 IO-APIC-edge ide1
16: 9646 9627 IO-APIC-level es1371
17: 28430 28517 IO-APIC-level aic7xxx
19: 45890 45280 IO-APIC-level eth0, usb-uhci, usb-uhci
NMI: 0 0
LOC: 319056 319075
ERR: 0
MIS: 0
# dmesg
Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1992.29 BogoMIPS
Memory: 512688k/524224k available (1673k kernel code, 11148k reserved, 570k data, 248k init, 0k highmem)
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000
CPU serial number disabled.
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Coppermine) stepping 0a
per-CPU timeslice cutoff: 730.97 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1992.29 BogoMIPS
CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000
CPU serial number disabled.
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU1: Intel Pentium III (Coppermine) stepping 0a
Total of 2 processors activated (3984.58 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-18, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 20.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178011
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 003 03 0 0 0 0 0 1 1 51
07 003 03 0 0 0 0 0 1 1 59
08 003 03 0 0 0 0 0 1 1 61
09 003 03 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 003 03 0 0 0 0 0 1 1 71
0d 003 03 0 0 0 0 0 1 1 79
0e 003 03 0 0 0 0 0 1 1 81
0f 003 03 0 0 0 0 0 1 1 89
10 003 03 1 1 0 1 0 1 1 91
11 003 03 1 1 0 1 0 1 1 99
12 000 00 1 0 0 0 0 0 0 00
13 003 03 1 1 0 1 0 1 1 A1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ19 -> 0:19
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 998.3772 MHz.
..... host bus clock speed is 133.1168 MHz.
cpu: 0, clocks: 1331168, slice: 443722
CPU0<T0:1331168,T1:887440,D:6,S:443722,C:1331168>
cpu: 1, clocks: 1331168, slice: 443722
CPU1<T0:1331168,T1:443712,D:12,S:443722,C:1331168>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs
PCI: PCI BIOS revision 2.10 entry at 0xfb370, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
PCI->APIC IRQ transform: (B0,I7,P3) -> 19
PCI->APIC IRQ transform: (B0,I7,P3) -> 19
PCI->APIC IRQ transform: (B0,I9,P0) -> 16
PCI->APIC IRQ transform: (B0,I10,P0) -> 17
PCI->APIC IRQ transform: (B0,I12,P0) -> 19
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI: Enabling Via external APIC routing
PCI: Via IRQ fixup for 00:07.2, from 10 to 3
PCI: Via IRQ fixup for 00:07.3, from 10 to 3
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.15)
apm: disabled - APM is not SMP safe (power off active).
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
Journalled Block Device driver loaded
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
parport0: faking semi-colon
parport0: Multimedia device, Connectix Color QuickCam 2.0
parport_pc: Via 686A parallel port: io=0x378
matroxfb: Matrox Millennium G200 (AGP) detected
matroxfb: MTRR's turned on
matroxfb: 640x480x8bpp (virtual: 640x26208)
matroxfb: framebuffer at 0xD7000000, mapped to 0xe0812000, size 16777216
Console: switching to colour frame buffer device 80x30
fb0: MATROX VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: 128 slots per queue, batch=32
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:pio
hda: ST320430A, ATA DISK drive
hdb: WDC AC420400D, ATA DISK drive
hdc: Maxtor 4G120J6, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 40079088 sectors (20520 MB) w/512KiB Cache, CHS=2494/255/63, UDMA(33)
hdb: 39876480 sectors (20417 MB) w/1966KiB Cache, CHS=2482/255/63, UDMA(33)
hdc: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=238216/16/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2
/dev/ide/host0/bus0/target1/lun0: p1 p2
/dev/ide/host0/bus1/target0/lun0: p1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
00:0c.0: 3Com PCI 3c595 Vortex 100baseTx at 0xe400. Vers LK1.1.16
00:0c.0: Overriding PCI latency timer (CFLT) setting of 32, new value is 248.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro chipset
agpgart: AGP aperture is 64M @ 0xd0000000
SCSI subsystem driver Revision: 1.00
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.4
<Adaptec 29160N Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Vendor: HP Model: C1537A Rev: L706
Type: Sequential-Access ANSI SCSI revision: 02
(scsi0:A:4): 10.000MB/s transfers (10.000MHz, offset 32)
Vendor: YAMAHA Model: CRW2100S Rev: 1.0H
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:5): 20.000MB/s transfers (20.000MHz, offset 7)
st: Version 20011103, bufsize 32768, wrt 30720, max init. bufs 4, s/g segs 16
Attached scsi tape st0 at scsi0, channel 0, id 4, lun 0
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
es1371: version v0.30 time 20:04:37 Jan 6 2002
es1371: found chip, vendor id 0x1274 device id 0x5880 revision 0x02
es1371: found es1371 rev 2 at io 0xdc00 irq 16
es1371: features: joystick 0x0
ac97_codec: AC97 codec, id: 0x5452:0x4123 (TriTech TR A5)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 1728.400 MB/sec
32regs : 1225.200 MB/sec
pIII_sse : 2058.400 MB/sec
pII_mmx : 2242.000 MB/sec
p5_mmx : 2360.000 MB/sec
raid5: using function: pIII_sse (2058.400 MB/sec)
md: multipath personality registered as nr 7
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
[events: 0000002d]
[events: 00000026]
[events: 0000002d]
[events: 00000026]
[events: 0000002a]
md: autorun ...
md: considering ide/host0/bus1/target0/lun0/part1 ...
md: adding ide/host0/bus1/target0/lun0/part1 ...
md: created md10
md: bind<ide/host0/bus1/target0/lun0/part1,1>
md: running: <ide/host0/bus1/target0/lun0/part1>
md: ide/host0/bus1/target0/lun0/part1's event counter: 0000002a
md: RAID level 1 does not need chunksize! Continuing anyway.
md10: max total readahead window set to 124k
md10: 1 data-disks, max readahead per data-disk: 124k
raid1: device ide/host0/bus1/target0/lun0/part1 operational as mirror 0
raid1: md10, not all disks are operational -- trying to recover array
raid1: raid set md10 active with 1 out of 2 mirrors
md: recovery thread got woken up ...
md10: no spare disk to reconstruct array! -- continuing in degraded mode
md: recovery thread finished ...
md: updating md10 RAID superblock on device
md: ide/host0/bus1/target0/lun0/part1 [events: 0000002b]<6>(write) ide/host0/bus1/target0/lun0/part1's sb offset: 120060736
md: considering ide/host0/bus0/target1/lun0/part2 ...
md: adding ide/host0/bus0/target1/lun0/part2 ...
md: adding ide/host0/bus0/target0/lun0/part2 ...
md: created md2
md: bind<ide/host0/bus0/target0/lun0/part2,1>
md: bind<ide/host0/bus0/target1/lun0/part2,2>
md: running: <ide/host0/bus0/target1/lun0/part2><ide/host0/bus0/target0/lun0/part2>
md: ide/host0/bus0/target1/lun0/part2's event counter: 00000026
md: ide/host0/bus0/target0/lun0/part2's event counter: 00000026
md: RAID level 1 does not need chunksize! Continuing anyway.
md2: max total readahead window set to 124k
md2: 1 data-disks, max readahead per data-disk: 124k
raid1: device ide/host0/bus0/target1/lun0/part2 operational as mirror 1
raid1: device ide/host0/bus0/target0/lun0/part2 operational as mirror 0
raid1: raid set md2 active with 2 out of 2 mirrors
md: updating md2 RAID superblock on device
md: ide/host0/bus0/target1/lun0/part2 [events: 00000027]<6>(write) ide/host0/bus0/target1/lun0/part2's sb offset: 530048
md: ide/host0/bus0/target0/lun0/part2 [events: 00000027]<6>(write) ide/host0/bus0/target0/lun0/part2's sb offset: 530048
md: considering ide/host0/bus0/target1/lun0/part1 ...
md: adding ide/host0/bus0/target1/lun0/part1 ...
md: adding ide/host0/bus0/target0/lun0/part1 ...
md: created md1
md: bind<ide/host0/bus0/target0/lun0/part1,1>
md: bind<ide/host0/bus0/target1/lun0/part1,2>
md: running: <ide/host0/bus0/target1/lun0/part1><ide/host0/bus0/target0/lun0/part1>
md: ide/host0/bus0/target1/lun0/part1's event counter: 0000002d
md: ide/host0/bus0/target0/lun0/part1's event counter: 0000002d
md: RAID level 1 does not need chunksize! Continuing anyway.
md1: max total readahead window set to 124k
md1: 1 data-disks, max readahead per data-disk: 124k
raid1: device ide/host0/bus0/target1/lun0/part1 operational as mirror 0
raid1: device ide/host0/bus0/target0/lun0/part1 operational as mirror 1
raid1: raid set md1 active with 2 out of 2 mirrors
md: updating md1 RAID superblock on device
md: ide/host0/bus0/target1/lun0/part1 [events: 0000002e]<6>(write) ide/host0/bus0/target1/lun0/part1's sb offset: 19406400
md: ide/host0/bus0/target0/lun0/part1 [events: 0000002e]<6>(write) ide/host0/bus0/target0/lun0/part1's sb offset: 19502784
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 248k freed
Adding Swap: 530040k swap-space (priority -1)
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide0(3,1), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on md(9,10), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usb-uhci.c: $Revision: 1.268 $ time 20:05:57 Jan 6 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.268:USB Universal Host Controller Interface driver
VFS: Disk change detected on device sr(11,0)
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
diagnostics: net 0c80 media 88c0 dma ffffffff.
eth0: Updating statistics failed, disabling stats as an interrupt source.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
diagnostics: net 0c80 media 88c0 dma ffffffff.
scsi0: PCI error Interrupt at seqaddr = 0x8
scsi0: Data Parity Error Detected during address or write data phase
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
diagnostics: net 0c80 media 88c0 dma ffffffff.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/