Hi everyone,
first of all a Happy New Year to all of you and all the best too!
And now to the problem....
I have a Dell Inspiron 8000 Laptop with PIII Mobile processor. I'm
trying to find a suitable kernel configuration that would allow me to
use the infrared port with my Nokia phone on a day-to-day basis and not
only occasionally ( well, basicly it works when it wants to, not when I
want it to - I might get a suitable result from irdadump promptly
reporting the phone being there, and then keep on trying for five days
with irdadump being blind for it all the time )... And untill then I'm
stuck with old bloody Windows (R!!!).
From what I've tried so far, the best setup is to have local APIC with
IO-APIC + ACPI for power management. APM won't do it at all. But I seem
to have a problem with APIC and changes of the power state. APIC gets
discovered and enabled when the kernel boots with no indication of any
problem. ACPI works too. Now, if I detach the power cable when it's
plugged in or vice versa, the system hangs without any chance for
recovery than hard boot. Here is the setup:
Debian GNU/Linux, testing
Dell Inspiron 8000, PIII Mobile@700-800MHz, Intel i815 chpset, 256 MB RAM
SMC-IRCC infrared chip LPC47N252 (if that matters to anyone)
acpi-20011205 patch (unpached vanilla source from 2.4.16 up compiles but
is not working, gives many errors in acpi at boot about something not
being true owner or similar)
avm1_cs isdn patch
obeserved hang behavior allways reproducable with kernels 2.4.16,
2.4.17-pre8, 2.4.17, 2.4.18-pre1, 2.5.1, 2.5.2-pre3 with APIC + either
ACPI or APM, tried compiles with gcc-2.95.4, gcc-3.0.1, gcc-3.0.2, gcc-3.0.3
This hangs occures allways when APIC support on uniprocessors is
compiled in, no matter what power managemnet sheme is used. It never
occures when APIC is not present, no matter of which kernel version
you'd take. Besides this, with APIC compiled in, shutdown -h or even
halt -f fails to pwer off the sistem (it goes down and halted but the
power remains on). I couldn't find anything in my logs that would help
indicateing the problem....
.config and dmesg attached (without APIC, just add it and you'll make
the difference between the two setups).
Kindly regards,
Todor
PS The only difference in dmesg with APIC is the 2 lines near the top:
Local APIC for uniprocessors found
APIC disabled by bios, reenableing
Anyone got any clue?
--------------080804080904080606090203
Content-Type: text/plain;
name="kconf"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="kconf"
#
# Automatically generated make config: don't edit
#
CONFIG_X86=y
CONFIG_ISA=y
# CONFIG_SBUS is not set
CONFIG_UID16=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y
#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
CONFIG_MPENTIUMIII=y
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_L1_CACHE_SHIFT=5
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_PGE=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
# CONFIG_TOSHIBA is not set
CONFIG_I8K=y
CONFIG_MICROCODE=m
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=m
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_SMP is not set
# CONFIG_X86_UP_APIC is not set
#
# General setup
#
CONFIG_NET=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_NAMES=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
CONFIG_HOTPLUG=y
#
# PCMCIA/CardBus support
#
CONFIG_PCMCIA=m
CONFIG_CARDBUS=y
# CONFIG_I82092 is not set
# CONFIG_I82365 is not set
# CONFIG_TCIC is not set
#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set
CONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
# CONFIG_BINFMT_AOUT is not set
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
CONFIG_PM=y
# CONFIG_APM is not set
#
# ACPI Support
#
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_DEBUG=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_BUS=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_CML1=m
CONFIG_PARPORT_SERIAL=m
CONFIG_PARPORT_PC_FIFO=y
CONFIG_PARPORT_PC_SUPERIO=y
# CONFIG_PARPORT_PC_PCMCIA is not set
# CONFIG_PARPORT_AMIGA is not set
# CONFIG_PARPORT_MFC3 is not set
# CONFIG_PARPORT_ATARI is not set
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_SUNBPP is not set
CONFIG_PARPORT_OTHER=y
CONFIG_PARPORT_1284=y
#
# Plug and Play configuration
#
CONFIG_PNP=y
CONFIG_ISAPNP=y
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=m
CONFIG_BLK_DEV_RAM_SIZE=4096
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
# CONFIG_NETLINK is not set
# CONFIG_NETFILTER is not set
CONFIG_FILTER=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_INET_ECN is not set
CONFIG_SYN_COOKIES=y
# CONFIG_IPV6 is not set
# CONFIG_KHTTPD is not set
# CONFIG_ATM is not set
# CONFIG_VLAN_8021Q is not set
#
#
#
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_LLC is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# ATA/IDE/MFM/RLL support
#
CONFIG_IDE=y
#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
# CONFIG_BLK_DEV_COMMERIAL is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
#
# IDE chipset support/bugfixes
#
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_BLK_DEV_ADMA=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
CONFIG_BLK_DEV_PIIX=y
CONFIG_PIIX_TUNING=y
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set
# CONFIG_DMA_NONPCI is not set
CONFIG_BLK_DEV_IDE_MODES=y
# CONFIG_BLK_DEV_ATARAID is not set
#
# SCSI support
#
CONFIG_SCSI=m
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
CONFIG_SD_EXTRA_DEVS=40
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
CONFIG_CHR_DEV_SG=m
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_DEBUG is not set
#
# PCMCIA SCSI adapter support
#
# CONFIG_SCSI_PCMCIA is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_BOOT is not set
# CONFIG_FUSION_ISENSE is not set
# CONFIG_FUSION_CTL is not set
# CONFIG_FUSION_LAN is not set
#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
CONFIG_IEEE1394=m
#
# Device Drivers
#
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=m
#
# Protocol Drivers
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
CONFIG_IEEE1394_RAWIO=m
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_NET_SB1000 is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_CS89x0 is not set
# CONFIG_DE2104X is not set
# CONFIG_TULIP is not set
# CONFIG_DE4X5 is not set
# CONFIG_DGRS is not set
# CONFIG_DM9102 is not set
CONFIG_EEPRO100=m
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_SK98LIN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPPOE=m
# CONFIG_SLIP is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# PCMCIA network device support
#
CONFIG_NET_PCMCIA=y
CONFIG_PCMCIA_3C589=m
CONFIG_PCMCIA_3C574=m
CONFIG_PCMCIA_FMVJ18X=m
CONFIG_PCMCIA_PCNET=m
CONFIG_PCMCIA_NMCLAN=m
CONFIG_PCMCIA_SMC91C92=m
CONFIG_PCMCIA_XIRC2PS=m
CONFIG_PCMCIA_AXNET=m
CONFIG_PCMCIA_XIRCOM=m
CONFIG_PCMCIA_XIRTULIP=m
CONFIG_NET_PCMCIA_RADIO=y
CONFIG_PCMCIA_RAYCS=m
CONFIG_PCMCIA_NETWAVE=m
CONFIG_PCMCIA_WAVELAN=m
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
CONFIG_IRDA=m
#
# IrDA protocols
#
CONFIG_IRLAN=m
CONFIG_IRNET=m
CONFIG_IRCOMM=m
CONFIG_IRDA_ULTRA=y
#
# IrDA options
#
CONFIG_IRDA_CACHE_LAST_LSAP=y
CONFIG_IRDA_FAST_RR=y
CONFIG_IRDA_DEBUG=y
#
# Infrared-port device drivers
#
#
# SIR device drivers
#
CONFIG_IRTTY_SIR=m
CONFIG_IRPORT_SIR=m
#
# Dongle support
#
# CONFIG_DONGLE is not set
#
# FIR device drivers
#
# CONFIG_USB_IRDA is not set
# CONFIG_NSC_FIR is not set
# CONFIG_WINBOND_FIR is not set
# CONFIG_TOSHIBA_FIR is not set
CONFIG_SMC_IRCC_FIR=m
# CONFIG_ALI_FIR is not set
# CONFIG_VLSI_FIR is not set
#
# ISDN subsystem
#
CONFIG_ISDN=m
CONFIG_ISDN_PPP=y
CONFIG_ISDN_PPP_VJ=y
CONFIG_ISDN_MPP=y
CONFIG_ISDN_PPP_BSDCOMP=m
CONFIG_ISDN_AUDIO=y
CONFIG_ISDN_TTY_FAX=y
#
# ISDN feature submodules
#
CONFIG_ISDN_DRV_LOOP=m
CONFIG_ISDN_DIVERSION=m
#
# low-level hardware drivers
#
#
# Passive ISDN cards
#
CONFIG_ISDN_DRV_HISAX=m
#
# D-channel protocol features
#
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
# CONFIG_HISAX_NO_SENDCOMPLETE is not set
# CONFIG_HISAX_NO_LLC is not set
# CONFIG_HISAX_NO_KEYPAD is not set
# CONFIG_HISAX_1TR6 is not set
# CONFIG_HISAX_NI1 is not set
#
# HiSax supported cards
#
# CONFIG_HISAX_16_0 is not set
# CONFIG_HISAX_16_3 is not set
# CONFIG_HISAX_TELESPCI is not set
# CONFIG_HISAX_S0BOX is not set
# CONFIG_HISAX_AVM_A1 is not set
# CONFIG_HISAX_FRITZPCI is not set
CONFIG_HISAX_AVM_A1_PCMCIA=y
# CONFIG_HISAX_ELSA is not set
# CONFIG_HISAX_IX1MICROR2 is not set
# CONFIG_HISAX_DIEHLDIVA is not set
# CONFIG_HISAX_ASUSCOM is not set
# CONFIG_HISAX_TELEINT is not set
# CONFIG_HISAX_HFCS is not set
# CONFIG_HISAX_SEDLBAUER is not set
# CONFIG_HISAX_SPORTSTER is not set
# CONFIG_HISAX_MIC is not set
# CONFIG_HISAX_NETJET is not set
# CONFIG_HISAX_NETJET_U is not set
# CONFIG_HISAX_NICCY is not set
# CONFIG_HISAX_ISURF is not set
# CONFIG_HISAX_HSTSAPHIR is not set
# CONFIG_HISAX_BKM_A4T is not set
# CONFIG_HISAX_SCT_QUADRO is not set
# CONFIG_HISAX_GAZEL is not set
# CONFIG_HISAX_HFC_PCI is not set
# CONFIG_HISAX_W6692 is not set
# CONFIG_HISAX_HFC_SX is not set
# CONFIG_HISAX_DEBUG is not set
# CONFIG_HISAX_SEDLBAUER_CS is not set
# CONFIG_HISAX_ELSA_CS is not set
# CONFIG_HISAX_ST5481 is not set
# CONFIG_HISAX_FRITZ_PCIPNP is not set
#
# Active ISDN cards
#
# CONFIG_ISDN_DRV_ICN is not set
# CONFIG_ISDN_DRV_PCBIT is not set
# CONFIG_ISDN_DRV_SC is not set
# CONFIG_ISDN_DRV_ACT2000 is not set
# CONFIG_ISDN_DRV_EICON is not set
# CONFIG_ISDN_DRV_TPAM is not set
# CONFIG_ISDN_CAPI is not set
# CONFIG_HYSDN is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Input core support
#
CONFIG_INPUT=m
CONFIG_INPUT_KEYBDEV=m
CONFIG_INPUT_MOUSEDEV=m
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1400
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=1050
# CONFIG_INPUT_JOYDEV is not set
CONFIG_INPUT_EVDEV=m
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
# CONFIG_SERIAL_CONSOLE is not set
# CONFIG_SERIAL_ACPI is not set
# CONFIG_SERIAL_EXTENDED is not set
# CONFIG_SERIAL_NONSTANDARD is not set
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set
#
# I2C support
#
# CONFIG_I2C is not set
#
# Mice
#
# CONFIG_BUSMOUSE is not set
CONFIG_MOUSE=y
CONFIG_PSMOUSE=y
# CONFIG_82C710_MOUSE is not set
# CONFIG_PC110_PAD is not set
#
# Joysticks
#
# CONFIG_INPUT_GAMEPORT is not set
# CONFIG_INPUT_SERIO is not set
#
# Joysticks
#
# CONFIG_INPUT_IFORCE_USB is not set
# CONFIG_INPUT_DB9 is not set
# CONFIG_INPUT_GAMECON is not set
# CONFIG_INPUT_TURBOGRAFX is not set
# CONFIG_QIC02_TAPE is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_INTEL_RNG is not set
CONFIG_NVRAM=y
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=m
CONFIG_AGP_INTEL=y
CONFIG_AGP_I810=y
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_DRM is not set
#
# PCMCIA character devices
#
# CONFIG_PCMCIA_SERIAL_CS is not set
# CONFIG_MWAVE is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# File systems
#
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_BFS_FS is not set
CONFIG_EXT3_FS=y
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FAT_FS=m
# CONFIG_MSDOS_FS is not set
CONFIG_VFAT_FS=m
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
CONFIG_TMPFS=y
CONFIG_RAMFS=y
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_MINIX_FS=m
# CONFIG_VXFS_FS is not set
CONFIG_NTFS_FS=m
# CONFIG_NTFS_RW is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
CONFIG_DEVPTS_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
CONFIG_UDF_FS=y
# CONFIG_UDF_RW is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_CODA_FS=m
# CONFIG_INTERMEZZO_FS is not set
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
CONFIG_SUNRPC=m
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_SMB_FS=m
CONFIG_SMB_NLS_DEFAULT=y
CONFIG_SMB_NLS_REMOTE="cp850"
# CONFIG_NCP_FS is not set
CONFIG_ZISOFS_FS=y
CONFIG_ZLIB_FS_INFLATE=y
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_SMB_NLS=y
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_DEFAULT="iso8859-15"
# CONFIG_NLS_CODEPAGE_437 is not set
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=m
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ISO8859_1=m
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
CONFIG_NLS_ISO8859_5=m
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=m
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=m
#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
CONFIG_VIDEO_SELECT=y
# CONFIG_MDA_CONSOLE is not set
#
# Frame-buffer support
#
# CONFIG_FB is not set
#
# Sound
#
CONFIG_SOUND=m
# CONFIG_SOUND_BT878 is not set
# CONFIG_SOUND_CMPCI is not set
# CONFIG_SOUND_EMU10K1 is not set
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
CONFIG_SOUND_MAESTRO3=m
# CONFIG_SOUND_ICH is not set
# CONFIG_SOUND_RME96XX is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_SOUND_OSS is not set
#
# USB support
#
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_BANDWIDTH=y
CONFIG_USB_LONG_TIMEOUT=y
#
# USB Controllers
#
# CONFIG_USB_UHCI is not set
CONFIG_USB_UHCI_ALT=m
# CONFIG_USB_OHCI is not set
#
# USB Device Class drivers
#
CONFIG_USB_AUDIO=m
# CONFIG_USB_BLUETOOTH is not set
CONFIG_USB_STORAGE=m
CONFIG_USB_STORAGE_DEBUG=y
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_HP8200e=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_JUMPSHOT=y
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
#
# USB Human Interface Devices (HID)
#
CONFIG_USB_HID=m
CONFIG_USB_HIDDEV=y
CONFIG_USB_KBD=m
CONFIG_USB_MOUSE=m
CONFIG_USB_WACOM=m
#
# USB Imaging devices
#
CONFIG_USB_DC2XX=m
CONFIG_USB_MDC800=m
CONFIG_USB_SCANNER=m
CONFIG_USB_MICROTEK=m
CONFIG_USB_HPUSBSCSI=m
#
# USB Multimedia devices
#
#
# Video4Linux support is needed for USB Multimedia device support
#
#
# USB Network adaptors
#
CONFIG_USB_PEGASUS=m
CONFIG_USB_KAWETH=m
CONFIG_USB_CATC=m
CONFIG_USB_CDCETHER=m
CONFIG_USB_USBNET=m
#
# USB port drivers
#
CONFIG_USB_USS720=m
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
#
# USB Miscellaneous drivers
#
CONFIG_USB_RIO500=m
#
# Bluetooth support
#
# CONFIG_BLUEZ is not set
#
# Kernel hacking
#
# CONFIG_DEBUG_KERNEL is not set
--------------080804080904080606090203
Content-Type: text/plain;
name="dmsg.out"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="dmsg.out"
Linux version 2.5.2-pre3-acpi (root@skrkg100) (gcc version 2.95.4 20011223 (Debian prerelease)) #2 Mon Dec 31 21:01:25 UTC 2001
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 0000000000100000 - 000000000ffea800 (usable)
BIOS-e820: 000000000ffea800 - 0000000010000000 (reserved)
BIOS-e820: 00000000feea0000 - 00000000fef00000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 65514
zone(0): 4096 pages.
zone(1): 61418 pages.
zone(2): 0 pages.
ACPI: RSD PTR (v0 DELL ) @ 0x000fde50
ACPI: RSDT (v1 DELL CPi R 10193.2324) @ 0x000fde64
ACPI: FACP (v1 DELL CPi R 10193.2324) @ 0x000fde90
Kernel command line: root=/dev/hda3 vga=5
Initializing CPU#0
Detected 797.360 MHz processor.
Console: colour VGA+ 80x34
Calibrating delay loop... 1592.52 BogoMIPS
Memory: 255572k/262056k available (1193k kernel code, 6096k reserved, 363k data, 196k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 0a
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfc06e, last bus=8
PCI: Using configuration type 1
tbxface-0099 [01] Acpi_load_tables : ACPI Tables successfully loaded
Parsing Methods:..........................................................................................................................................................
154 Control Methods found and parsed (363 nodes total)
ACPI Namespace successfully loaded at root c02ca5e8
ACPI: Core Subsystem version [20011205]
evxfevnt-0081 [02] Acpi_enable : Transition to ACPI mode successful
Executing device _INI methods:....................................................
52 Devices found: 52 _STA, 3 _INI
Completing Region and Field initialization:..
0/2 Regions, 2/10 Fields initialized (363 nodes total)
ACPI: Subsystem enabled
ACPI: Power Resource found
ACPI: System firmware supports S1 S3 S4 S5
ACPI: PCI Root Bridge (bus 00)
PCI: Probing PCI hardware (bus 00)
Unknown bridge resource 2: assuming transparent
Unknown bridge resource 2: assuming transparent
ACPI: PCI Routing Table (bus 00)
device=1f pin=00 irq=11
device=1f pin=01 irq=5
device=1f pin=02 irq=7
device=1f pin=03 irq=11
device=01 pin=00 irq=11
device=01 pin=01 irq=5
ACPI: PCI Routing Table (bus 01)
device=00 pin=00 irq=11
ACPI: PCI Routing Table (bus 02)
device=0f pin=00 irq=11
device=0f pin=01 irq=11
device=0f pin=02 irq=11
device=03 pin=00 irq=5
device=06 pin=00 irq=11
device=06 pin=01 irq=7
device=08 pin=00 irq=7
ACPI: PCI Routing Table (bus ff)
device=00 pin=00 irq=0
PCI: Using IRQ router PIIX [8086/244c] at 00:1f.0
PCI: Found IRQ 11 for device 02:0f.0
PCI: Sharing IRQ 11 with 00:1f.2
PCI: Sharing IRQ 11 with 02:0f.1
PCI: Sharing IRQ 11 with 02:0f.2
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd
BIO: pool of 256 setup, 14Kb (56 bytes/bio)
biovec: init pool 0, 1 entries, 12 bytes
biovec: init pool 1, 4 entries, 48 bytes
biovec: init pool 2, 16 entries, 192 bytes
biovec: init pool 3, 64 entries, 768 bytes
biovec: init pool 4, 128 entries, 1536 bytes
biovec: init pool 5, 256 entries, 3072 bytes
Journalled Block Device driver loaded
udf: registering filesystem
ACPI: Processor[0]: C0 C1 C2
ACPI: Battery socket found, battery absent
ACPI: Battery socket found, battery present
ACPI: AC Adapter found
ACPI: Power Button (CM) found
ACPI: Sleep Button (CM) found
ACPI: Lid Switch (CM) found
ACPI: Thermal Zone found
pty: 256 Unix98 ptys configured
Inspiron 8000 SMM driver v1.1 02/11/2001 Massimo Dal Zotto (dz@debian.org)
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Non-volatile memory driver v1.1
block: 256 slots per queue, batch=32
Uniform Multi-Platform E-IDE driver Revision: 6.32
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2-M: IDE controller on PCI slot 00:1f.1
ICH2-M: chipset revision 3
ICH2-M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:pio, hdd:pio
hda: HITACHI_DK23BA-20, ATA DISK drive
hdb: LG DVD-ROM DRN-8080B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
blk: queue c02e60a4, I/O limit 4095Mb (mask 0xffffffff)
hda: 39070080 sectors (20004 MB) w/2048KiB Cache, CHS=2432/255/63, UDMA(66)
hdb: ATAPI DVD-ROM drive, 512kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 196k freed
Adding Swap: 489940k swap-space (priority -1)
EXT3 FS 2.4-0.9.15, 06 Nov 2001 on ide0(3,3), internal journal
maestro3: version 1.22 built at 19:15:20 Dec 31 2001
PCI: Found IRQ 5 for device 02:03.0
maestro3: Configuring ESS Maestro3(i) found at IO 0xDC00 IRQ 5
maestro3: subvendor id: 0x00a41028
ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
eth0: OEM i82557/i82558 10/100 Ethernet, 00:20:E0:69:12:4F, IRQ 11.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 727095-002, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
Receiver lock-up workaround activated.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: agpgart: Detected an Intel i815, but could not find the secondary device. Assuming a non-integrated video card.
agpgart: Detected Intel i815 chipset
agpgart: AGP aperture is 64M @ 0xe8000000
NVRM: loading NVIDIA NVdriver Kernel Module 1.0.2313 Tue Nov 27 12:01:24 PST 2001
MSDOS FS: Using codepage 850
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Enabling device 02:0f.0 (0000 -> 0002)
PCI: Found IRQ 11 for device 02:0f.0
PCI: Sharing IRQ 11 with 00:1f.2
PCI: Sharing IRQ 11 with 02:0f.1
PCI: Sharing IRQ 11 with 02:0f.2
PCI: Enabling device 02:0f.1 (0000 -> 0002)
PCI: Found IRQ 11 for device 02:0f.1
PCI: Sharing IRQ 11 with 00:1f.2
PCI: Sharing IRQ 11 with 02:0f.0
PCI: Sharing IRQ 11 with 02:0f.2
Yenta IRQ list 0498, PCI irq11
Socket status: 30000006
Yenta IRQ list 0498, PCI irq11
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x280-0x287 0x370-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
irda_init()
ircc_init
ircc_init Try to open all known SMC chipsets
smc_superio_flat()
smc_probe()
smc_access()
smc_superio_paged()
smc_probe()
smc_access()
smc_superio_flat()
smc_probe()
smc_access()
smc_superio_paged()
smc_probe()
smc_access()
smc_superio_flat()
smc_probe()
smc_access()
smc_superio_paged()
smc_probe()
smc_access()
smc_superio_flat()
smc_probe()
smc_access()
smc_access()
smc_superio_paged()
smc_probe()
smc_access()
smc_access()
smc_access()
found SMC SuperIO Chip (devid=0x0e rev=01 base=0x002e): LPC47N252
ircc_open
SMC IrDA Controller found
IrCC version 2.0, firport 0x280, sirport 0x2f8 dma=3, irq=3
irport_open_R749eb1f5()
irport_open_R749eb1f5(), can't get iobase of 0x2f8
smc_superio_flat()
smc_probe()
smc_access()
smc_superio_paged()
smc_probe()
smc_access()
irport_close_R7fc631f0(), Releasing Region 2f8
usb.c: registered new driver usbfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 11 for device 00:1f.2
PCI: Sharing IRQ 11 with 02:0f.0
PCI: Sharing IRQ 11 with 02:0f.1
PCI: Sharing IRQ 11 with 02:0f.2
PCI: Setting latency timer of device 00:1f.2 to 64
uhci.c: USB UHCI at I/O 0xbce0, IRQ 11
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
lp0: using parport0 (polling).
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
NVRM: AGPGART: Intel i815 chipset
NVRM: AGPGART: aperture: 64M @ 0xe8000000
NVRM: AGPGART: aperture mapped from 0xe8000000 to 0xd59fa000
NVRM: AGPGART: mode 4x
NVRM: AGPGART: allocated 16 pages
VFS: Disk change detected on device ide0(3,64)
--------------080804080904080606090203--
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/