> Hi!
>
> We experience a problem with a HP Ultrium LTO drive connected
> to a Compaq ProLiant ML380 server: in the last 6 months we had
> two deadlocks of the machine which seem to be related to the
> sym53c8xx driver.
>
> What happens seems to be as follows:
>
> *) From monday to friday, once a day an amanda backup process
> starts and dumps about 70GB of data to the tape.
>
> *) this works quite fine, but twice in the last 6 months we
> got the following tape error at the start of the backup:
>
> [...]
> Dec 10 15:00:00 server kernel: sym53c1510D-0-<3,*>: FAST-20 WIDE SCSI
> 40.0 MB/s (50 ns, offset 15)
This messages indicates teh synchronous parameters that have been
negotiated with the device.
> Dec 10 15:00:01 server kernel: st0: Error with sense data: Info
> fld=0x8000, Current st09:00: sense key Hardware Error
> Dec 10 15:00:01 server kernel: Additional sense indicates Internal
> target failure
This one is the result of a REQUEST SENSE performed due probably to a
CHECK condition SCSI status reported by the device. It is not a SCSI
transport problem. The device just reports an error to the application
client. This is not a normal situation but happens very often.
> [...]
>
> After that, the amanda process hangs in state "D" and
> cannot be killed anymore. The machine itself is still
> working.
> This _seems_ to be the indication of an error of the
> HP Ultrium itself, though the drive works quite fine
> otherwise...
The 'D' states indicates that the process is waiting for something without
being interruptible. This may be due to it not having been waken up on the
IO error. The sym53c8xx driver did its work by performing the REQUEST
SENSE, but something in upper layer seem not to complete the IO.
> *) In order to unlock the hanging amanda process I tried to
> remove the SCSI drive from the driver:
>
> echo "scsi remove-single-device" > /proc/scsi/scsi
>
> This did work well: the hanging amanda process terminated
> fine after that.
Hmmm... You seems brave. :-)
> *) Next I tried to re-scan the SCSI bus to make the Ultrium
> drive available again for a new backup:
>
> echo "scsi add-single-device 0 0 3 0" > /proc/scsi/scsi
>
> Result: the machine completely deadlocked. No log-message,
> no ping (the server currently runs without monitor and
> keyboard connected...)
> We had to power-switch the machine to get it back... :-(
But certainly too much. :)
To be serious, I cannot explain what happenned here. But something was
messy since the hang-up, so you should only expect some luck here to help
you.
> I now have the following problems/questions:
>
> a) Does anyone have any experience with such an HP Ultrium drive?
> (good/bad?)
None, here.
> b) Does the st0 error message indicate it should be replaced?
Probably not. But it is very poor an information about the real issue.
> c) Is there a bug in the sym53c8xx driver which makes the
> amanda process hang uninterruptable when this error occurs?
Not known. But possible, even if in my opinion, the driver is not at
fault.
> It is not nice to be forced to reboot the machine just because
> the SCSI tape drive reported some error... :-((
Agreed.
> After all, this is not a windows server, and there are 40
> workstations which get fileservice from this server!
>
> d) Is there a bug in the driver which deadlocks the server
> as soon as someone does a remove/add on the SCSI bus?
> We can live without this feature, but I don't think a
> documented function should deadlock the kernel...
There are probably still bugs in the driver, but none are intentionnal,
beleive me.
> The Ultrium hardware error is not reproducable at will. It
> just happens every now and then.
> Next thing I will try is to use a different SCSI controller
> (Adaptec 29160 or the like) to see if the hanging process
> occurs with a different SCSI driver, too.
This is indeed something to try.
I am very interested in the result.
Gérard.
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> Following is some information about the server:
>
> Hardware: Compaq ProLiant ML370, Intel PIII/933, 512MB RAM,
> Compaq Smart Array 5302/32 RAID Controller with about 80GB
> of disk-capacity, 3Com 3c985 1000BaseSX NIC
>
> Software: Linux-2.2.18 with newer acenic driver (for the 3Com NIC)
>
> Some information from the running system:
>
> root@server {533} # free
> total used free shared buffers
> cached
> Mem: 517644 439092 78552 47404 166716
> 178744
> -/+ buffers/cache: 93632 424012
> Swap: 1052592 18400 1034192
>
> root@server {534} # lspci -v
> 00:00.0 Host bridge: Relience Computer CNB20HE (rev 05)
> Flags: bus master, medium devsel, latency 64
>
> 00:00.1 Host bridge: Relience Computer CNB20HE (rev 05)
> Flags: bus master, medium devsel, latency 64
>
> 00:01.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR):
> Unknown device 000a (rev 02)
> Subsystem: Compaq Computer Corporation: Unknown device b143
> Flags: bus master, medium devsel, latency 255, IRQ 10
> I/O ports at 2000
> Memory at c6cffc00 (32-bit, non-prefetchable)
> Memory at c6cfe000 (32-bit, non-prefetchable)
> Capabilities: [40] Power Management version 2
>
> 00:01.1 SCSI storage controller: Symbios Logic Inc. (formerly NCR):
> Unknown device 000a (rev 02)
> Subsystem: Compaq Computer Corporation: Unknown device b143
> Flags: bus master, medium devsel, latency 255, IRQ 11
> I/O ports at 2400
> Memory at c6cfdc00 (32-bit, non-prefetchable)
> Memory at c6cfc000 (32-bit, non-prefetchable)
> Capabilities: [40] Power Management version 2
>
> 00:02.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro
> 100] (rev 08)
> Subsystem: Compaq Computer Corporation: Unknown device b134
> Flags: bus master, medium devsel, latency 64, IRQ 15
> Memory at c6cfb000 (32-bit, non-prefetchable)
> I/O ports at 2800
> Memory at c6b00000 (32-bit, non-prefetchable)
> Capabilities: [dc] Power Management version 2
>
> 00:03.0 VGA compatible controller: ATI Technologies Inc 3D Rage IIC
> 215IIC [Mach64 GT IIC] (rev 7a) (prog-if 00 [VGA])
> Subsystem: ATI Technologies Inc: Unknown device 4756
> Flags: bus master, stepping, medium devsel, latency 64
> Memory at c5000000 (32-bit, prefetchable)
> I/O ports at 2c00
> Memory at c6aff000 (32-bit, non-prefetchable)
> Capabilities: [5c] Power Management version 1
>
> 00:04.0 System peripheral: Compaq Computer Corporation: Unknown device
> a0f0
> Subsystem: Compaq Computer Corporation: Unknown device b0f3
> Flags: medium devsel
> I/O ports at 1800
> Memory at c6afef00 (32-bit, non-prefetchable)
>
> 00:0f.0 ISA bridge: Relience Computer: Unknown device 0200 (rev 51)
> Subsystem: Relience Computer: Unknown device 0200
> Flags: bus master, medium devsel, latency 0
>
> 00:0f.1 IDE interface: Relience Computer: Unknown device 0211 (prog-if
> 8a [Master SecP PriP])
> Flags: bus master, medium devsel, latency 64
> I/O ports at 3000
>
> 03:03.0 RAID bus controller: Compaq Computer Corporation: Unknown
> device b060 (rev 02)
> Subsystem: Compaq Computer Corporation: Unknown device 4070
> Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 5
> Memory at c6fc0000 (32-bit, non-prefetchable)
> Memory at c6e00000 (32-bit, non-prefetchable)
> I/O ports at 4000
> Capabilities: [f0] Power Management version 2
> Capabilities: [f8] Vital Product Data
>
> 03:06.0 Ethernet controller: 3Com Corporation 3c985 1000BaseSX (rev
> 01)
> Subsystem: Unknown device 9850:0001
> Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 15
> Memory at c6dfc000 (32-bit, non-prefetchable)
>
>
> root@server {535} # cat /proc/cciss/cciss0
> cciss0: Compaq Smart Array 5300 Controller
> Board ID: 40700e11
> Firmware Version: 1.62
> Memory Address: e0812000
> IRQ: 0x5
> Logical drives: 2
> Current Q depth: 0
> Current # commands on controller 0
> Max Q depth since init: 1
> Max # commands on controller since init: 128
> Max SG entries since init: 22
>
> cciss/c0d0: blksz=512 nr_blocks=17764320
> cciss/c0d1: blksz=512 nr_blocks=142261440
> nr_allocs = 11831533
> nr_frees = 11831533
>
> root@server {536} # cat /proc/scsi/scsi
> Attached devices:
> Host: scsi0 Channel: 00 Id: 03 Lun: 00
> Vendor: HP Model: Ultrium 1-SCSI Rev: N11D
> Type: Sequential-Access ANSI SCSI revision: 03
>
> root@server {537} # cat /proc/scsi/sym53c8xx/0
> General information:
> Chip sym53c1510D, device id 0xa, revision id 0x2
> On PCI bus 0, device 1, function 0, IRQ 10
> Synchronous period factor 10, max commands per lun 32
>
> root@server {538} # cat /proc/scsi/sym53c8xx/1
> General information:
> Chip sym53c1510D, device id 0xa, revision id 0x2
> On PCI bus 0, device 1, function 1, IRQ 11
> Synchronous period factor 10, max commands per lun 32
>
> root@server {539} # cat /proc/interrupts
> CPU0
> 0: 76904808 XT-PIC timer
> 1: 2 XT-PIC keyboard
> 2: 0 XT-PIC cascade
> 3: 5231002 XT-PIC serial
> 5: 11578119 XT-PIC cciss0
> 8: 2 XT-PIC rtc
> 10: 13412657 XT-PIC sym53c8xx
> 11: 450 XT-PIC sym53c8xx
> 13: 1 XT-PIC fpu
> 15: 36100885 XT-PIC eth0
> NMI: 0
> ERR: 0
>
> root@server {540} # uname -a
> Linux server 2.2.18 #1 SMP Sun May 27 23:14:43 CEST 2001 i686 unknown
>
> root@server {541} # lsmod
> Module Size Used by
> sym53c8xx 56592 0
> af_packet 6528 1 (autoclean)
> nfsd 184416 16 (autoclean)
> nfs 75872 1 (autoclean)
> lockd 47344 1 (autoclean) [nfsd nfs]
> sunrpc 63376 1 (autoclean) [nfsd nfs lockd]
> acenic 125744 1 (autoclean)
> softdog 1584 1 (autoclean)
> st 25424 0
> scsi_mod 55504 2 [sym53c8xx st]
> cciss 17552 9
> ext2 42032 7
>
>
> These are the sym53c8xx driver's boot-messages:
> [...]
> sym53c8xx: at PCI bus 0, device 1, function 0
> sym53c8xx: 53c1510D detected
> sym53c8xx: at PCI bus 0, device 1, function 1
> sym53c8xx: 53c1510D detected
> sym53c1510D-0: rev 0x2 on pci bus 0 device 1 function 0 irq 10
> sym53c1510D-0: ID 7, Fast-40, Parity Checking
> sym53c1510D-1: rev 0x2 on pci bus 0 device 1 function 1 irq 11
> sym53c1510D-1: ID 7, Fast-40, Parity Checking
> scsi0 : sym53c8xx-1.7.1-20000726
> scsi1 : sym53c8xx-1.7.1-20000726
> scsi : 2 hosts.
> Vendor: HP Model: Ultrium 1-SCSI Rev: N11D
> Type: Sequential-Access ANSI SCSI revision: 03
> Detected scsi tape st0 at scsi0, channel 0, id 3, lun 0
> [...]
>
> Any help is appreciated!
> Many thanks in advance!
>
> - andreas
>
> --
> Andreas Haumer | mailto:andreas@xss.co.at
> *x Software + Systeme | http://www.xss.co.at/
> Karmarschgasse 51/2/20 | Tel: +43-1-6060114-0
> A-1100 Vienna, Austria | Fax: +43-1-6060114-71
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/