Re: IDE controller detection 2.4 +devfs

[Rene Rebe]

Are there any new results or comments regarding this issue ??

On Thu, 29 Nov 2001 19:10:52 -0700
Richard Gooch <[e-mail]> wrote:

> Rene Rebe writes:
> > On Thu, 29 Nov 2001 18:11:21 -0700
> > Richard Gooch <[e-mail]> wrote:
> > 
> > > But it is actually predictable, isn't it? Think of it this way: the
> > > IDE subsystem reserves "slots" (host numbers) for installed hardware.
> > > If a piece of hardware is disabled in the BIOS, it doesn't mean that
> > > the slot won't be reserved.
> > 
> > It would be nice if it would be that way - se below.
> > 
> > > > (All info from my very first mail ...)
> > > > 
> > > > The other bug is: On a Athlon-600 workstation based on an Irongate
> > > > board (Asus-K7M) I have to disable the first (primarry) channel of
> > > > the onbaord IDE controller, because it has problem with the UDMA-66
> > > > mode. But when I disable this channel, Linux generates a /dev/ide/host1
> > > > entry - No host0 entry is there. Sure it works - but sucks, too!
> > > > (Generates a very unstable feeling in me ...)
> > > 
> > > The "host0" entry isn't shown, because it is disabled. But to say
> > > "when I disable this channel, Linux generates a /dev/ide/host1" isn't
> > > correct, and implies a problem where there isn't. The correct way to
> > > describe this is:
> > > "host0" is my primary onboard IDE controller. It might not appear if I
> > > disable it.
> > > "host1" is my secondary onboard IDE controller. It has the same name
> > > whether or not I disable the primary.
> > 
> > No!!!! On the Althon box:
> > - nothing disabled in BIOS:
> > /dev/ide/host0/bus0/ - on-board primary channel
> > /deV/ide/host0/bus1/ - on-board secondary channel
> > 
> > - when I disable the primary channel I get this:
> > /dev/ide/host1/bus1/ - on-board secondary channel
> > 
> > So as you can see it moves!! From host0 to host1!
> 
> Oh, fuck! Now I see why you're complaining. Yeah, that is busted. I
> don't know why this happens. It may be due to some deep and subtle
> workings of the IDE code.
> 
> Andre: any idea why this is happening?
> 
> > > And this is a Feature[tm]. It means that tomorrow when a shiny new
> > > drive arrives, you can plug it into your primary channel and enable
> > > the channel in the BIOS. You can then boot without having to fix your
> > > /etc/fstab, because /dev/ide/host1 is still pointing to the same
> > > devices.
> > 
> > Yes that is a really cool advantage I now for months (over a year!)!
> > But here is the next example again:
> > 
> > The K6 server (on-board ALI-Aladin-5 + PCI-Card Promisse controller):
> > 
> > /dev/ide/host0/bus0/ - on-board primary channel
> > /dev/ide/host0/bus1/ - on-board secondary channel
> > /dev/ide/host2/bus0/ - Promisse primary channel
> > /dev/ide/host2/bus1/ - Promisse secondarychannel
> > 
> > So where is host1 ??????
> 
> Good question. I wonder what's taking up the "host1" slot?
> 
> 				Regards,
> 
> 					Richard....
> Permanent: [e-mail]
> Current:   [e-mail]

k33p h4ck1n6
  René

-- 
René Rebe (Registered Linux user: #248718 <http://counter.li.org>)

eMail:    [e-mail]
          [e-mail]

Homepage: http://www.tfh-berlin.de/~s712059/index.html

Anyone sending unwanted advertising e-mail to this address will be
charged $25 for network traffic and computing time. By extracting my
address from this message or its header, you agree to these terms.