The machine in question has one 99% active Oracle shadow process, with
kswapd eating about 17-20% CPU at all times. Per the top listings
below, Oracle is set to use a ~840M SGA. Interactive performance is
poor, behaving like moderate to severe swapping. A higher SGA increases
the severity of the problem -- 1.4GB seems to cause the machine to run
away and hide more or less permanently.
However, when a remote machine begins to copy a ~20MB file to this
machine via scp, the following top screen displays and the machine is
essentially frozen for a significant period of time (roughly 15 minutes
to two hours):
12:22am up 1 day, 35 min, 1 user, load average: 7.23, 4.35, 4.27
85 processes: 79 sleeping, 6 running, 0 zombie, 0 stopped
CPU states: 0.0% user, 98.4% system, 0.0% nice, 1.4% idle
Mem: 3343692K av, 3339124K used, 4568K free, 0K shrd, 368K buff
Swap: 1004052K av, 194920K used, 809132K free 2522428K cached
PID USER PRI NI SIZE RSS SHARE STAT LIB %CPU %MEM TIME COMMAND
11 root 17 0 0 0 0 RW 0 99.9 0.0 24:09 kupdated
2562 oracle 18 0 5964 5632 5488 R 3972 99.9 0.1 34:41 oracle
2912 oracle 11 0 840M 839M 278M D 255M 93.7 25.7 134:49 oracle
9 root 14 0 0 0 0 RW 0 88.3 0.0 77:04 kswapd
3273 root 14 0 888 888 672 R 0 47.5 0.0 1:07 top
3279 webrot 14 0 580 580 472 R 0 42.7 0.0 0:27 scp
3282 root 14 0 1092 1072 888 R 0 8.3 0.0 0:01 sshd
It looks like all quasi-active processes begin to "use" 100% system CPU
time. When the machine recovers 15-120 minutes later, the load has shot
up to >17 and the memory state seems unchanged. kswapd reappears at
70-80% CPU usage and slowly drops back down to an oscillating 20-90%
range. Swap usage continues to slowly creep higher:
12:39am up 1 day, 52 min, 1 user, load average: 2.02, 8.16, 9.07
82 processes: 80 sleeping, 2 running, 0 zombie, 0 stopped
CPU states: 3.9% user, 21.9% system, 0.0% nice, 74.1% idle
Mem: 3343692K av, 3340728K used, 2964K free, 0K shrd, 416K buff
Swap: 1004052K av, 207016K used, 797036K free 2516988K cached
PID USER PRI NI SIZE RSS SHARE STAT LIB %CPU %MEM TIME COMMAND
2912 oracle 14 0 855M 854M 280M D 254M 87.6 26.1 143:26 oracle
9 root 19 0 0 0 0 RW 0 61.5 0.0 82:43 kswapd
3273 root 18 0 896 868 744 R 0 3.4 0.0 5:49 top
The issue gets better and worse over time without a specific period.
Other kinds of load on this type of machine and kernel seem fine, from
heavy compilation to a development platform for dozens of heavily-active
developers, NFS, etc.
A secondary issue is that kswapd before this hang event is eating 20-90%
more CPU than I think it should :) especially given Oracle's static SGA
that fits well within RAM. I understand that the quantitative swap
usage could be quite normal based on page age, but it's slightly
worrying that so much swap is being used, given that the page cache is
2.5GB.
This machine is an HP LH6000r (6-way Xeon) with 4GB of RAM (minus the
700MB that HP needs for hot-swappable PCI. I hate HP.) I've seen this
since 2.4.13, but didn't try anything between 2.4.9 and 2.4.13
exclusive. Currently running is 2.4.15-pre1 with Marcelo's vmscan
patch. I know it won't be "baptized", but it does seem to slightly
reduce the severity and length of the hang state.
Basically, this problem makes it impossible to run Oracle on Linux,
which is really a massive problem from our point of view. If someone
could show me how to provide more useful information or further debug
this problem, I would greatly appreciate it. This includes specific
alternate kernels, or perhaps without HIGHMEM4G or HIGHMEM.
I've attached some various stats etc below just to cover bases. This
example is not a pristine 2.4.15-pre1, due to the long-standing IO-APIC
issues and various other VM-unrelated patches, but the issue also
reproduces on pristine versions of 2.4.1{3,4,5-pre1}.
Thanks much,
-- Ken. brownfld@irridia.comNothing notable in syslogs.
[root@skunk ~]$ cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 10 model name : Pentium III (Cascades) stepping : 0 cpu MHz : 700.084 cache size : 2048 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 1395.91
processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 10 model name : Pentium III (Cascades) stepping : 1 cpu MHz : 700.084 cache size : 2048 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 1399.19
processor : 2 vendor_id : GenuineIntel cpu family : 6 model : 10 model name : Pentium III (Cascades) stepping : 1 cpu MHz : 700.084 cache size : 2048 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 1399.19
processor : 3 vendor_id : GenuineIntel cpu family : 6 model : 10 model name : Pentium III (Cascades) stepping : 1 cpu MHz : 700.084 cache size : 2048 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 1399.19
processor : 4 vendor_id : GenuineIntel cpu family : 6 model : 10 model name : Pentium III (Cascades) stepping : 0 cpu MHz : 700.084 cache size : 2048 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 1399.19
processor : 5 vendor_id : GenuineIntel cpu family : 6 model : 10 model name : Pentium III (Cascades) stepping : 0 cpu MHz : 700.084 cache size : 2048 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 1399.19
[root@skunk ~]$ cat /proc/slabinfo slabinfo - version: 1.1 (SMP) kmem_cache 64 64 244 4 4 1 : 252 126 ip_fib_hash 11 452 32 4 4 1 : 252 126 ip_mrt_cache 0 0 96 0 0 1 : 252 126 tcp_tw_bucket 0 0 128 0 0 1 : 252 126 tcp_bind_bucket 11 452 32 4 4 1 : 252 126 tcp_open_request 0 0 96 0 0 1 : 252 126 inet_peer_cache 0 0 64 0 0 1 : 252 126 ip_dst_cache 33 220 192 11 11 1 : 252 126 arp_cache 5 90 128 3 3 1 : 252 126 blkdev_requests 512 520 96 13 13 1 : 252 126 journal_head 9 234 48 3 3 1 : 252 126 revoke_table 2 506 12 2 2 1 : 252 126 revoke_record 0 0 32 0 0 1 : 252 126 dnotify cache 0 0 20 0 0 1 : 252 126 file lock cache 91 504 92 12 12 1 : 252 126 fasync cache 0 0 16 0 0 1 : 252 126 uid_cache 6 565 32 5 5 1 : 252 126 skbuff_head_cache 1132 2064 160 86 86 1 : 252 126 sock 52 60 928 15 15 1 : 124 62 sigqueue 188 319 132 11 11 1 : 252 126 cdev_cache 11 413 64 7 7 1 : 252 126 bdev_cache 8 354 64 6 6 1 : 252 126 mnt_cache 15 295 64 5 5 1 : 252 126 inode_cache 10235 38368 480 4796 4796 1 : 124 62 dentry_cache 432 1650 128 55 55 1 : 252 126 dquot 0 0 128 0 0 1 : 252 126 filp 1216 1500 128 50 50 1 : 252 126 names_cache 4 4 4096 4 4 1 : 60 30 buffer_head 561764 719760 96 17994 17994 1 : 252 126 mm_struct 66 336 160 14 14 1 : 252 126 vm_area_struct 1845 2560 96 64 64 1 : 252 126 fs_cache 69 472 64 8 8 1 : 252 126 files_cache 69 234 416 26 26 1 : 124 62 signal_act 74 135 1312 45 45 1 : 60 30 size-131072(DMA) 0 0 131072 0 0 32 : 0 0 size-131072 0 0 131072 0 0 32 : 0 0 size-65536(DMA) 0 0 65536 0 0 16 : 0 0 size-65536 19 19 65536 19 19 16 : 0 0 size-32768(DMA) 0 0 32768 0 0 8 : 0 0 size-32768 2 2 32768 2 2 8 : 0 0 size-16384(DMA) 0 0 16384 0 0 4 : 0 0 size-16384 1 1 16384 1 1 4 : 0 0 size-8192(DMA) 0 0 8192 0 0 2 : 0 0 size-8192 3 3 8192 3 3 2 : 0 0 size-4096(DMA) 0 0 4096 0 0 1 : 60 30 size-4096 43 43 4096 43 43 1 : 60 30 size-2048(DMA) 0 0 2048 0 0 1 : 60 30 size-2048 679 756 2048 378 378 1 : 60 30 size-1024(DMA) 0 0 1024 0 0 1 : 124 62 size-1024 264 284 1024 71 71 1 : 124 62 size-512(DMA) 0 0 512 0 0 1 : 124 62 size-512 295 296 512 37 37 1 : 124 62 size-256(DMA) 0 0 256 0 0 1 : 252 126 size-256 165 165 256 11 11 1 : 252 126 size-128(DMA) 0 0 128 0 0 1 : 252 126 size-128 750 750 128 25 25 1 : 252 126 size-64(DMA) 0 0 64 0 0 1 : 252 126 size-64 315 708 64 12 12 1 : 252 126 size-32(DMA) 0 0 32 0 0 1 : 252 126 size-32 964 2147 32 19 19 1 : 252 126
[root@skunk ~]$ cat /proc/meminfo total: used: free: shared: buffers: cached: Mem: 3423940608 3421167616 2772992 0 417792 2616827904 Swap: 1028149248 215212032 812937216 MemTotal: 3343692 kB MemFree: 2708 kB MemShared: 0 kB Buffers: 408 kB Cached: 2511388 kB SwapCached: 44108 kB Active: 1097100 kB Inactive: 2126344 kB HighTotal: 2482112 kB HighFree: 1136 kB LowTotal: 861580 kB LowFree: 1572 kB SwapTotal: 1004052 kB SwapFree: 793884 kB
[root@skunk ~]$ dmesg -s32768 Linux version 2.4.15-pre1kb2 (root@aenea.XXX.com) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 SMP Wed Nov 7 23:03:00 PST 2001 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009e000 (usable) BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e5c00 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000c40f0000 (usable) BIOS-e820: 00000000c40f0000 - 00000000c40ffc00 (ACPI data) BIOS-e820: 00000000c40ffc00 - 00000000c4100000 (ACPI NVS) BIOS-e820: 00000000c4100000 - 00000000cf800000 (usable) BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 2424MB HIGHMEM available. found SMP MP-table at 000f7590 hm, page 000f7000 reserved twice. hm, page 000f8000 reserved twice. hm, page 0009e000 reserved twice. hm, page 0009f000 reserved twice. On node 0 totalpages: 849920 zone(0): 4096 pages. zone(1): 225280 pages. zone(2): 620544 pages. Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: HP Product ID: LH 6000 APIC at: 0xFEE00000 Processor #6 Pentium(tm) Pro APIC version 17 Processor #0 Pentium(tm) Pro APIC version 17 Processor #1 Pentium(tm) Pro APIC version 17 Processor #2 Pentium(tm) Pro APIC version 17 Processor #4 Pentium(tm) Pro APIC version 17 Processor #5 Pentium(tm) Pro APIC version 17 I/O APIC #3 Version 17 at 0xFEC00000. I/O APIC #7 Version 17 at 0xFEC01000. Processors: 6 Kernel command line: auto BOOT_IMAGE=linux ro root=801 no8259A Initializing CPU#0 Detected 700.084 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 1395.91 BogoMIPS Memory: 3343460k/3399680k available (1387k kernel code, 55764k reserved, 477k data, 232k init, 2482112k highmem) Dentry-cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Mount-cache hash table entries: 65536 (order: 7, 524288 bytes) Buffer-cache hash table entries: 262144 (order: 8, 1048576 bytes) Page-cache hash table entries: 524288 (order: 9, 2097152 bytes) CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 2048K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000 CPU serial number disabled. CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 2048K Intel machine check reporting enabled on CPU#0. CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000 CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU0: Intel Pentium III (Cascades) stepping 00 per-CPU timeslice cutoff: 5846.34 usecs. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Booting processor 1/0 eip 2000 Initializing CPU#1 masked ExtINT on CPU#1 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 1399.19 BogoMIPS CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 2048K Intel machine check reporting enabled on CPU#1. CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000 CPU serial number disabled. CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU1: Intel Pentium III (Cascades) stepping 01 Booting processor 2/1 eip 2000 Initializing CPU#2 masked ExtINT on CPU#2 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 1399.19 BogoMIPS CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 2048K Intel machine check reporting enabled on CPU#2. CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000 CPU serial number disabled. CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU2: Intel Pentium III (Cascades) stepping 01 Booting processor 3/2 eip 2000 Initializing CPU#3 masked ExtINT on CPU#3 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 1399.19 BogoMIPS CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 2048K Intel machine check reporting enabled on CPU#3. CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000 CPU serial number disabled. CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU3: Intel Pentium III (Cascades) stepping 01 Booting processor 4/4 eip 2000 Initializing CPU#4 masked ExtINT on CPU#4 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 1399.19 BogoMIPS CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 2048K Intel machine check reporting enabled on CPU#4. CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000 CPU serial number disabled. CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU4: Intel Pentium III (Cascades) stepping 00 Booting processor 5/5 eip 2000 Initializing CPU#5 masked ExtINT on CPU#5 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 1399.19 BogoMIPS CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 2048K Intel machine check reporting enabled on CPU#5. CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000 CPU serial number disabled. CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU5: Intel Pentium III (Cascades) stepping 00 Total of 6 processors activated (8391.88 BogoMIPS). ENABLING IO-APIC IRQs Setting 3 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 3 ... ok. Setting 7 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 7 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 3-0, 7-3, 7-10, 7-11, 7-12, 7-13, 7-14, 7-15 not connected. ..TIMER: vector=0x31 pin1=-1 pin2=0 ...trying to set up timer as Virtual Wire IRQ... works. number of MP IRQ sources: 34. number of IO-APIC #3 registers: 16. number of IO-APIC #7 registers: 16. testing the IO APIC.......................
IO APIC #3...... .... register #00: 03000000 ....... : physical APIC id: 03 .... register #01: 000F0011 ....... : max redirection entries: 000F ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 03000000 ....... : arbitration: 03 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 03F 0F 0 0 0 0 0 1 1 39 02 000 00 1 0 0 0 0 0 0 00 03 03F 0F 0 0 0 0 0 1 1 41 04 03F 0F 0 0 0 0 0 1 1 49 05 03F 0F 1 1 0 1 0 1 1 51 06 03F 0F 0 0 0 0 0 1 1 59 07 03F 0F 0 0 0 0 0 1 1 61 08 03F 0F 0 0 0 0 0 1 1 69 09 03F 0F 1 1 0 1 0 1 1 71 0a 03F 0F 1 1 0 1 0 1 1 79 0b 03F 0F 1 1 0 1 0 1 1 81 0c 03F 0F 0 0 0 0 0 1 1 89 0d 03F 0F 0 0 0 0 0 1 1 91 0e 03F 0F 0 0 0 0 0 1 1 99 0f 03F 0F 0 0 0 0 0 1 1 A1
IO APIC #7...... .... register #00: 07000000 ....... : physical APIC id: 07 .... register #01: 000F0011 ....... : max redirection entries: 000F ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 07000000 ....... : arbitration: 07 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 03F 0F 1 1 0 1 0 1 1 A9 01 03F 0F 1 1 0 1 0 1 1 B1 02 03F 0F 1 1 0 1 0 1 1 B9 03 000 00 1 0 0 0 0 0 0 00 04 03F 0F 1 1 0 1 0 1 1 C1 05 03F 0F 1 1 0 1 0 1 1 C9 06 03F 0F 1 1 0 1 0 1 1 D1 07 03F 0F 1 1 0 1 0 1 1 D9 08 03F 0F 1 1 0 1 0 1 1 E1 09 03F 0F 1 1 0 1 0 1 1 E9 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 000 00 1 0 0 0 0 0 0 00 0d 000 00 1 0 0 0 0 0 0 00 0e 000 00 1 0 0 0 0 0 0 00 0f 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ1 -> 0:1 IRQ2 -> 0:2 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 1:0 IRQ17 -> 1:1 IRQ18 -> 1:2 IRQ20 -> 1:4 IRQ21 -> 1:5 IRQ22 -> 1:6 IRQ23 -> 1:7 IRQ24 -> 1:8 IRQ25 -> 1:9 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 700.0558 MHz. ..... host bus clock speed is 100.0078 MHz. cpu: 0, clocks: 1000078, slice: 142868 CPU0<T0:1000064,T1:857184,D:12,S:142868,C:1000078> cpu: 1, clocks: 1000078, slice: 142868 cpu: 2, clocks: 1000078, slice: 142868 cpu: 3, clocks: 1000078, slice: 142868 cpu: 4, clocks: 1000078, slice: 142868 cpu: 5, clocks: 1000078, slice: 142868 CPU2<T0:1000064,T1:571456,D:4,S:142868,C:1000078> CPU1<T0:1000064,T1:714320,D:8,S:142868,C:1000078> CPU3<T0:1000064,T1:428592,D:0,S:142868,C:1000078> CPU4<T0:1000064,T1:285712,D:12,S:142868,C:1000078> CPU5<T0:1000064,T1:142848,D:8,S:142868,C:1000078> checking TSC synchronization across CPUs: passed. Waiting on wait_init_idle (map = 0x3e) All processors have done init_idle PCI: PCI BIOS revision 2.10 entry at 0xfd989, last bus=7 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Discovered primary peer bus 01 [IRQ] Unknown bridge resource 2: assuming transparent PCI: Discovered primary peer bus 04 [IRQ] PCI: Using IRQ router ServerWorks [1166/0200] at 00:0f.0 PCI->APIC IRQ transform: (B0,I6,P0) -> 18 PCI->APIC IRQ transform: (B2,I8,P0) -> 20 PCI->APIC IRQ transform: (B4,I2,P0) -> 16 PCI->APIC IRQ transform: (B4,I2,P1) -> 17 PCI->APIC IRQ transform: (B4,I3,P0) -> 21 PCI->APIC IRQ transform: (B5,I4,P0) -> 22 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd allocated 32 pages and 32 bhs reserved for the highmem bounces VFS: Diskquotas version dquot_6.4.0 initialized Journalled Block Device driver loaded pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A Real Time Clock Driver v1.10e Software Watchdog Timer: 0.05, timer margin: 60 sec block: 128 slots per queue, batch=32 Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ServerWorks OSB4: IDE controller on PCI bus 00 dev 79 ServerWorks OSB4: chipset revision 0 ServerWorks OSB4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1840-0x1847, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0x1848-0x184f, BIOS settings: hdc:pio, hdd:pio hda: CD-532E-B, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 NET4: Frame Diverter 0.46 loop: loaded (max 8 devices) DAC960: ***** DAC960 RAID Driver Version 2.4.11 of 11 October 2001 ***** DAC960: Copyright 1998-2001 by Leonard N. Zubkoff <lnz@dandelion.com> DAC960#0: Configuring Mylex eXtremeRAID 2000 PCI RAID Controller DAC960#0: Firmware Version: 6.00-01, Channels: 4, Memory Size: 64MB DAC960#0: PCI Bus: 2, Device: 8, Function: 0, I/O Address: Unassigned DAC960#0: PCI Address: 0xD2000000 mapped at 0xF8800000, IRQ Channel: 20 DAC960#0: Controller Queue Depth: 512, Maximum Blocks per Command: 2048 DAC960#0: Driver Queue Depth: 511, Scatter/Gather Limit: 128 of 257 Segments DAC960#0: Physical Devices: DAC960#0: 0:5 Vendor: HP Model: SAFTE; U160/M BP Revision: 1020 DAC960#0: Asynchronous DAC960#0: Serial Number: [ DAC960#0: 0:7 Vendor: MYLEX Model: eXtremeRAID 2000 Revision: 0600 DAC960#0: Wide Synchronous at 160 MB/sec DAC960#0: Serial Number: DAC960#0: 0:10 Vendor: HP Model: 36.4GB C 80-8C32 Revision: DAC960#0: Wide Synchronous at 80 MB/sec DAC960#0: Serial Number: 3CD06PWA DAC960#0: Disk Status: Online, 71098368 blocks DAC960#0: 0:11 Vendor: HP Model: 36.4GB C 80-8C32 Revision: DAC960#0: Wide Synchronous at 80 MB/sec DAC960#0: Serial Number: 3CD05CT9 DAC960#0: Disk Status: Online, 71098368 blocks DAC960#0: 0:12 Vendor: HP Model: 36.4GB C 80-8C32 Revision: DAC960#0: Wide Synchronous at 80 MB/sec DAC960#0: Serial Number: 3CD07111 DAC960#0: Disk Status: Online, 71098368 blocks DAC960#0: 0:13 Vendor: HP Model: 36.4GB C 80-8C32 Revision: DAC960#0: Wide Synchronous at 80 MB/sec DAC960#0: Serial Number: 3CD071NR DAC960#0: Disk Status: Online, 71098368 blocks DAC960#0: 0:14 Vendor: HP Model: 36.4GB C 80-8C32 Revision: DAC960#0: Wide Synchronous at 80 MB/sec DAC960#0: Serial Number: 3CD06X36 DAC960#0: Disk Status: Online, 71098368 blocks DAC960#0: 0:15 Vendor: HP Model: 36.4GB C 80-8C32 Revision: DAC960#0: Wide Synchronous at 80 MB/sec DAC960#0: Serial Number: 3CD05BPL DAC960#0: Disk Status: Online, 71098368 blocks DAC960#0: 1:0 Vendor: HP Model: 36.4GB C 80-D94N Revision: D94N DAC960#0: Wide Synchronous at 80 MB/sec DAC960#0: Serial Number: 4FFWH733 DAC960#0: Disk Status: Online, 71098368 blocks DAC960#0: 1:1 Vendor: HP Model: 36.4GB C 80-D94N Revision: D94N DAC960#0: Wide Synchronous at 80 MB/sec DAC960#0: Serial Number: 4FFWQ327 DAC960#0: Disk Status: Online, 71098368 blocks DAC960#0: 1:2 Vendor: HP Model: 36.4GB C 80-D94N Revision: D94N DAC960#0: Wide Synchronous at 80 MB/sec DAC960#0: Serial Number: 4FFWM586 DAC960#0: Disk Status: Online, 71098368 blocks DAC960#0: 1:3 Vendor: HP Model: 36.4GB C 80-D94N Revision: D94N DAC960#0: Wide Synchronous at 80 MB/sec DAC960#0: Serial Number: 4FFWQ340 DAC960#0: Disk Status: Online, 71098368 blocks DAC960#0: 1:5 Vendor: HP Model: SAFTE; U160/M BP Revision: 1020 DAC960#0: Asynchronous DAC960#0: Serial Number: [ DAC960#0: 1:7 Vendor: MYLEX Model: eXtremeRAID 2000 Revision: 0600 DAC960#0: Wide Synchronous at 160 MB/sec DAC960#0: Serial Number: DAC960#0: 1:8 Vendor: HP Model: 36.4GB C 80-D94N Revision: D94N DAC960#0: Wide Synchronous at 80 MB/sec DAC960#0: Serial Number: 4FFWP201 DAC960#0: Disk Status: Online, 71098368 blocks DAC960#0: 1:9 Vendor: HP Model: 36.4GB C 80-D94N Revision: D94N DAC960#0: Wide Synchronous at 80 MB/sec DAC960#0: Serial Number: 4FFWP351 DAC960#0: Disk Status: Online, 71098368 blocks DAC960#0: 2:7 Vendor: MYLEX Model: eXtremeRAID 2000 Revision: 0600 DAC960#0: Wide Synchronous at 160 MB/sec DAC960#0: Serial Number: DAC960#0: 3:7 Vendor: MYLEX Model: eXtremeRAID 2000 Revision: 0600 DAC960#0: Wide Synchronous at 160 MB/sec DAC960#0: Serial Number: DAC960#0: Logical Drives: DAC960#0: /dev/rd/c0d0: RAID-5, Online, 355450880 blocks DAC960#0: Logical Device Initialized, BIOS Geometry: 255/63 DAC960#0: Stripe Size: 64KB, Segment Size: 8KB DAC960#0: Read Cache Disabled, Write Cache Enabled DAC960#0: /dev/rd/c0d1: RAID-0, Online, 426541056 blocks DAC960#0: Logical Device Initialized, BIOS Geometry: 255/63 DAC960#0: Stripe Size: 64KB, Segment Size: 8KB DAC960#0: Read Cache Disabled, Write Cache Enabled Partition check: rd/c0d0:<7>LDM: DEBUG (ldm.c, 898): validate_partition_table: Found basic MS-DOS partition, not a dynamic disk. rd/c0d0p1 rd/c0d0p2 rd/c0d0p3 rd/c0d1:<7>LDM: DEBUG (ldm.c, 898): validate_partition_table: Found basic MS-DOS partition, not a dynamic disk. rd/c0d1p1 rd/c0d1p2 rd/c0d1p3 rd/c0d1p4 < rd/c0d1p5 rd/c0d1p6 rd/c0d1p7 > SCSI subsystem driver Revision: 1.00 Loading Adaptec I2O RAID: Version 2.4 Build 5 Detecting Adaptec I2O RAID controllers... megaraid: v1.18 (Release Date: Thu Oct 11 15:02:53 EDT 2001 )<5>megaraid: found 0x8086:0x1960:idx 0:bus 4:slot 3:func 1 scsi0 : Found a MegaRAID controller at 0xf8802000, IRQ: 21 megaraid: [:B ] detected 1 logical drives megaraid: channel[1] is raid. megaraid: channel[2] is raid. scsi0 : LSI Logic MegaRAID 254 commands 16 targs 5 chans 7 luns scsi0: scanning channel 0 for devices. scsi0: scanning channel 1 for devices. scsi0: scanning virtual channel 1 for logical drives. Vendor: MegaRAID Model: LD0 RAID1 8677R Rev: E Type: Direct-Access ANSI SCSI revision: 02 scsi0: scanning virtual channel 2 for logical drives. scsi0: scanning virtual channel 3 for logical drives. scsi0: scanning virtual channel 4 for logical drives. Attached scsi disk sda at scsi0, channel 2, id 0, lun 0 SCSI device sda: 17770496 512-byte hdwr sectors (9098 MB) sda:<7>LDM: DEBUG (ldm.c, 898): validate_partition_table: Found basic MS-DOS partition, not a dynamic disk. sda1 sda2 md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 962.000 MB/sec 32regs : 636.800 MB/sec pIII_sse : 1398.800 MB/sec pII_mmx : 1554.800 MB/sec p5_mmx : 1650.800 MB/sec raid5: using function: pIII_sse (1398.800 MB/sec) md: multipath personality registered as nr 7 md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. LVM version 0.9.1_beta2 by Heinz Mauelshagen (18/01/2001) lvm -- Driver successfully initialized NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 32768 buckets, 256Kbytes TCP: Hash tables configured (established 262144 bind 65536) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 232k freed DAC960#0: Physical Device 0:5 Found DAC960#0: Physical Device 1:5 Found DAC960#0: Physical Device 1:0 Found DAC960#0: Physical Device 1:1 Found DAC960#0: Physical Device 1:2 Found DAC960#0: Physical Device 1:3 Found DAC960#0: Physical Device 1:8 Found DAC960#0: Physical Device 1:9 Found DAC960#0: Physical Device 0:10 Found DAC960#0: Physical Device 0:11 Found DAC960#0: Physical Device 0:12 Found DAC960#0: Physical Device 0:13 Found DAC960#0: Physical Device 0:14 Found DAC960#0: Physical Device 0:15 Found DAC960#0: Physical Device 0:10 Online DAC960#0: Physical Device 0:11 Online DAC960#0: Physical Device 0:12 Online DAC960#0: Physical Device 0:13 Online DAC960#0: Physical Device 0:14 Online DAC960#0: Physical Device 0:15 Online DAC960#0: Physical Device 1:0 Online DAC960#0: Physical Device 1:1 Online DAC960#0: Physical Device 1:2 Online DAC960#0: Physical Device 1:3 Online DAC960#0: Physical Device 1:8 Online DAC960#0: Physical Device 1:9 Online DAC960#0: Logical Drive 0 (/dev/rd/c0d0) Found DAC960#0: Logical Drive 0 (/dev/rd/c0d0) Online DAC960#0: Logical Drive 1 (/dev/rd/c0d1) Found DAC960#0: Logical Drive 1 (/dev/rd/c0d1) Online DAC960#0: Controller Battery Backup Unit Found DAC960#0: Enclosure 1 Temperature Sensor 0 Temperature Normal DAC960#0: Enclosure 2 Temperature Sensor 0 Temperature Normal Adding Swap: 1004052k swap-space (priority 1) kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.15, 06 Nov 2001 on dac960(48,11), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.15, 06 Nov 2001 on dac960(48,13), internal journal EXT3-fs: mounted filesystem with ordered data mode. sk98lin: Network Device Driver v4.06kb0 Copyright (C) 2000-2001 SysKonnect GmbH. divert: allocating divert_blk for eth0 eth0: SysKonnect SK-NET Gigabit Ethernet Adapter SK-9843 SX PrefPort:A RlmtMode:Check Link State eth0: network connection up using port A speed: 1000 autonegotiation: yes duplex mode: full flowctrl: symmetric
[root@aenea ~]$ cat /usr/src/linux/.config # # Automatically generated by make menuconfig: don't edit # CONFIG_X86=y CONFIG_ISA=y # CONFIG_SBUS is not set CONFIG_UID16=y
# # Code maturity level options # CONFIG_EXPERIMENTAL=y
# # Loadable module support # CONFIG_MODULES=y # CONFIG_MODVERSIONS is not set CONFIG_KMOD=y
# # Processor type and features # # CONFIG_M386 is not set # CONFIG_M486 is not set # CONFIG_M586 is not set # CONFIG_M586TSC is not set # CONFIG_M586MMX is not set # CONFIG_M686 is not set CONFIG_MPENTIUMIII=y # CONFIG_MPENTIUM4 is not set # CONFIG_MK6 is not set # CONFIG_MK7 is not set # CONFIG_MCRUSOE is not set # CONFIG_MWINCHIPC6 is not set # CONFIG_MWINCHIP2 is not set # CONFIG_MWINCHIP3D is not set # CONFIG_MCYRIXIII is not set CONFIG_X86_WP_WORKS_OK=y CONFIG_X86_INVLPG=y CONFIG_X86_CMPXCHG=y CONFIG_X86_XADD=y CONFIG_X86_BSWAP=y CONFIG_X86_POPAD_OK=y # CONFIG_RWSEM_GENERIC_SPINLOCK is not set CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_X86_L1_CACHE_SHIFT=5 CONFIG_X86_TSC=y CONFIG_X86_GOOD_APIC=y CONFIG_X86_PGE=y CONFIG_X86_USE_PPRO_CHECKSUM=y # CONFIG_TOSHIBA is not set # CONFIG_I8K is not set CONFIG_MICROCODE=m CONFIG_X86_MSR=m CONFIG_X86_CPUID=m # CONFIG_NOHIGHMEM is not set CONFIG_HIGHMEM4G=y # CONFIG_HIGHMEM64G is not set CONFIG_HIGHMEM=y # CONFIG_MATH_EMULATION is not set CONFIG_MTRR=y CONFIG_SMP=y # CONFIG_MULTIQUAD is not set CONFIG_HAVE_DEC_LOCK=y
# # General setup # CONFIG_NET=y CONFIG_X86_IO_APIC=y CONFIG_X86_LOCAL_APIC=y CONFIG_PCI=y # CONFIG_PCI_GOBIOS is not set # CONFIG_PCI_GODIRECT is not set CONFIG_PCI_GOANY=y CONFIG_PCI_BIOS=y CONFIG_PCI_DIRECT=y CONFIG_PCI_NAMES=y # CONFIG_EISA is not set # CONFIG_MCA is not set # CONFIG_HOTPLUG is not set # CONFIG_PCMCIA is not set CONFIG_SYSVIPC=y CONFIG_BSD_PROCESS_ACCT=y CONFIG_SYSCTL=y CONFIG_KCORE_ELF=y # CONFIG_KCORE_AOUT is not set CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=m # CONFIG_PM is not set # CONFIG_ACPI is not set # CONFIG_APM is not set
# # Memory Technology Devices (MTD) # # CONFIG_MTD is not set
# # Parallel port support # CONFIG_PARPORT=m CONFIG_PARPORT_PC=m CONFIG_PARPORT_PC_CML1=m CONFIG_PARPORT_SERIAL=m CONFIG_PARPORT_PC_FIFO=y # CONFIG_PARPORT_PC_SUPERIO is not set # CONFIG_PARPORT_AMIGA is not set # CONFIG_PARPORT_MFC3 is not set # CONFIG_PARPORT_ATARI is not set # CONFIG_PARPORT_SUNBPP is not set # CONFIG_PARPORT_OTHER is not set CONFIG_PARPORT_1284=y
# # Plug and Play configuration # # CONFIG_PNP is not set # CONFIG_ISAPNP is not set
# # Block devices # CONFIG_BLK_DEV_FD=y # CONFIG_BLK_DEV_XD is not set # CONFIG_PARIDE is not set # CONFIG_BLK_CPQ_DA is not set # CONFIG_BLK_CPQ_CISS_DA is not set CONFIG_BLK_DEV_DAC960=y CONFIG_BLK_DEV_LOOP=y CONFIG_BLK_DEV_NBD=m CONFIG_BLK_DEV_RAM=m CONFIG_BLK_DEV_RAM_SIZE=4096 # CONFIG_BLK_DEV_INITRD is not set
# # Multi-device support (RAID and LVM) # CONFIG_MD=y CONFIG_BLK_DEV_MD=y CONFIG_MD_LINEAR=y CONFIG_MD_RAID0=y CONFIG_MD_RAID1=y CONFIG_MD_RAID5=y CONFIG_MD_MULTIPATH=y CONFIG_BLK_DEV_LVM=y
# # Networking options # CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_NETLINK=y CONFIG_RTNETLINK=y # CONFIG_NETLINK_DEV is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set CONFIG_FILTER=y CONFIG_UNIX=y CONFIG_INET=y CONFIG_IP_MULTICAST=y CONFIG_IP_ADVANCED_ROUTER=y CONFIG_RTNETLINK=y CONFIG_NETLINK=y CONFIG_IP_MULTIPLE_TABLES=y CONFIG_IP_ROUTE_FWMARK=y CONFIG_IP_ROUTE_NAT=y CONFIG_IP_ROUTE_MULTIPATH=y CONFIG_IP_ROUTE_TOS=y CONFIG_IP_ROUTE_VERBOSE=y CONFIG_IP_ROUTE_LARGE_TABLES=y CONFIG_IP_PNP=y CONFIG_IP_PNP_DHCP=y # CONFIG_IP_PNP_BOOTP is not set # CONFIG_IP_PNP_RARP is not set CONFIG_NET_IPIP=m CONFIG_NET_IPGRE=m CONFIG_NET_IPGRE_BROADCAST=y CONFIG_IP_MROUTE=y CONFIG_IP_PIMSM_V1=y CONFIG_IP_PIMSM_V2=y # CONFIG_ARPD is not set CONFIG_INET_ECN=y CONFIG_SYN_COOKIES=y
# # IP: Netfilter Configuration # CONFIG_IP_NF_CONNTRACK=m CONFIG_IP_NF_FTP=m CONFIG_IP_NF_IRC=m CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_LIMIT=m CONFIG_IP_NF_POOL=m CONFIG_IP_POOL_STATISTICS=y CONFIG_IP_NF_MATCH_MAC=m CONFIG_IP_NF_MATCH_PKTTYPE=m CONFIG_IP_NF_MATCH_MARK=m CONFIG_IP_NF_MATCH_MULTIPORT=m CONFIG_IP_NF_MATCH_MPORT=m CONFIG_IP_NF_MATCH_TOS=m CONFIG_IP_NF_MATCH_TIME=m CONFIG_IP_NF_MATCH_PSD=m CONFIG_IP_NF_MATCH_RANDOM=m CONFIG_IP_NF_MATCH_NTH=m CONFIG_IP_NF_MATCH_IPV4OPTIONS=m CONFIG_IP_NF_MATCH_AH_ESP=m CONFIG_IP_NF_MATCH_LENGTH=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_MATCH_TCPMSS=m CONFIG_IP_NF_MATCH_REALM=m CONFIG_IP_NF_MATCH_STATE=m CONFIG_IP_NF_MATCH_IPLIMIT=m CONFIG_IP_NF_MATCH_UNCLEAN=m CONFIG_IP_NF_MATCH_OWNER=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_NETLINK=m CONFIG_IP_NF_TARGET_MIRROR=m CONFIG_IP_NF_NAT=m CONFIG_IP_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_SAME=m CONFIG_IP_NF_TARGET_NETMAP=m CONFIG_IP_NF_NAT_SNMP_BASIC=m CONFIG_IP_NF_NAT_IRC=m CONFIG_IP_NF_NAT_FTP=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_TOS=m CONFIG_IP_NF_TARGET_FTOS=m CONFIG_IP_NF_TARGET_MARK=m CONFIG_IP_NF_TARGET_LOG=m CONFIG_IP_NF_TARGET_ULOG=m CONFIG_IP_NF_TARGET_TTL=m CONFIG_IP_NF_TARGET_TCPMSS=m # CONFIG_IP_NF_COMPAT_IPCHAINS is not set # CONFIG_IP_NF_COMPAT_IPFWADM is not set CONFIG_IPV6=m
# # IPv6: Netfilter Configuration # CONFIG_IP6_NF_IPTABLES=m CONFIG_IP6_NF_MATCH_LIMIT=m CONFIG_IP6_NF_MATCH_MAC=m CONFIG_IP6_NF_MATCH_MULTIPORT=m CONFIG_IP6_NF_MATCH_OWNER=m CONFIG_IP6_NF_MATCH_MARK=m CONFIG_IP6_NF_MATCH_LENGTH=m CONFIG_IP6_NF_MATCH_AGR=m CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_TARGET_LOG=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_MARK=m CONFIG_KHTTPD=m # CONFIG_ATM is not set CONFIG_VLAN_8021Q=m # CONFIG_IPX is not set CONFIG_ATALK=m # CONFIG_DECNET is not set CONFIG_BRIDGE=m # CONFIG_X25 is not set # CONFIG_LAPB is not set # CONFIG_LLC is not set CONFIG_NET_DIVERT=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_NET_FASTROUTE is not set # CONFIG_NET_HW_FLOWCONTROL is not set
# # QoS and/or fair queueing # CONFIG_NET_SCHED=y CONFIG_NETLINK=y CONFIG_RTNETLINK=y CONFIG_NET_SCH_CBQ=m CONFIG_NET_SCH_CSZ=m CONFIG_NET_SCH_PRIO=m CONFIG_NET_SCH_RED=m CONFIG_NET_SCH_SFQ=m CONFIG_NET_SCH_TEQL=m CONFIG_NET_SCH_TBF=m CONFIG_NET_SCH_GRED=m CONFIG_NET_SCH_DSMARK=m CONFIG_NET_SCH_INGRESS=m CONFIG_NET_QOS=y CONFIG_NET_ESTIMATOR=y CONFIG_NET_CLS=y CONFIG_NET_CLS_TCINDEX=m CONFIG_NET_CLS_ROUTE4=m CONFIG_NET_CLS_ROUTE=y CONFIG_NET_CLS_FW=m CONFIG_NET_CLS_U32=m CONFIG_NET_CLS_RSVP=m CONFIG_NET_CLS_RSVP6=m CONFIG_NET_CLS_POLICE=y
# # Telephony Support # # CONFIG_PHONE is not set # CONFIG_PHONE_IXJ is not set # CONFIG_PHONE_IXJ_PCMCIA is not set
# # ATA/IDE/MFM/RLL support # CONFIG_IDE=y
# # IDE, ATA and ATAPI Block devices # CONFIG_BLK_DEV_IDE=y # CONFIG_BLK_DEV_HD_IDE is not set # CONFIG_BLK_DEV_HD is not set CONFIG_BLK_DEV_IDEDISK=y CONFIG_IDEDISK_MULTI_MODE=y # CONFIG_BLK_DEV_IDEDISK_VENDOR is not set # CONFIG_BLK_DEV_IDEDISK_FUJITSU is not set # CONFIG_BLK_DEV_IDEDISK_IBM is not set # CONFIG_BLK_DEV_IDEDISK_MAXTOR is not set # CONFIG_BLK_DEV_IDEDISK_QUANTUM is not set # CONFIG_BLK_DEV_IDEDISK_SEAGATE is not set # CONFIG_BLK_DEV_IDEDISK_WD is not set # CONFIG_BLK_DEV_COMMERIAL is not set # CONFIG_BLK_DEV_TIVO is not set # CONFIG_BLK_DEV_IDECS is not set CONFIG_BLK_DEV_IDECD=m CONFIG_BLK_DEV_IDETAPE=m CONFIG_BLK_DEV_IDEFLOPPY=m CONFIG_BLK_DEV_IDESCSI=m # CONFIG_BLK_DEV_CMD640 is not set # CONFIG_BLK_DEV_CMD640_ENHANCED is not set # CONFIG_BLK_DEV_ISAPNP is not set # CONFIG_BLK_DEV_RZ1000 is not set CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_BLK_DEV_IDEDMA_PCI=y CONFIG_BLK_DEV_ADMA=y # CONFIG_BLK_DEV_OFFBOARD is not set CONFIG_IDEDMA_PCI_AUTO=y CONFIG_BLK_DEV_IDEDMA=y # CONFIG_IDEDMA_PCI_WIP is not set # CONFIG_IDEDMA_NEW_DRIVE_LISTINGS is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_AEC62XX_TUNING is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_WDC_ALI15X3 is not set CONFIG_BLK_DEV_AMD74XX=y # CONFIG_AMD74XX_OVERRIDE is not set # CONFIG_BLK_DEV_CMD64X is not set # CONFIG_BLK_DEV_CY82C693 is not set # CONFIG_BLK_DEV_CS5530 is not set # CONFIG_BLK_DEV_HPT34X is not set # CONFIG_HPT34X_AUTODMA is not set # CONFIG_BLK_DEV_HPT366 is not set CONFIG_BLK_DEV_PIIX=y CONFIG_PIIX_TUNING=y # CONFIG_BLK_DEV_NS87415 is not set # CONFIG_BLK_DEV_OPTI621 is not set # CONFIG_BLK_DEV_PDC202XX is not set # CONFIG_PDC202XX_BURST is not set # CONFIG_PDC202XX_FORCE is not set CONFIG_BLK_DEV_SVWKS=y # CONFIG_BLK_DEV_SIS5513 is not set # CONFIG_BLK_DEV_SLC90E66 is not set # CONFIG_BLK_DEV_TRM290 is not set CONFIG_BLK_DEV_VIA82CXXX=y # CONFIG_IDE_CHIPSETS is not set CONFIG_IDEDMA_AUTO=y # CONFIG_IDEDMA_IVB is not set # CONFIG_DMA_NONPCI is not set CONFIG_BLK_DEV_IDE_MODES=y CONFIG_BLK_DEV_ATARAID=m CONFIG_BLK_DEV_ATARAID_PDC=m CONFIG_BLK_DEV_ATARAID_HPT=m
# # SCSI support # CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y CONFIG_SD_EXTRA_DEVS=40 CONFIG_CHR_DEV_ST=m # CONFIG_CHR_DEV_OSST is not set CONFIG_BLK_DEV_SR=m CONFIG_BLK_DEV_SR_VENDOR=y CONFIG_SR_EXTRA_DEVS=2 CONFIG_CHR_DEV_SG=m # CONFIG_SCSI_DEBUG_QUEUES is not set CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_LOGGING=y
# # SCSI low-level drivers # # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_7000FASST is not set # CONFIG_SCSI_ACARD is not set # CONFIG_SCSI_AHA152X is not set # CONFIG_SCSI_AHA1542 is not set # CONFIG_SCSI_AHA1740 is not set CONFIG_SCSI_AIC7XXX=y CONFIG_AIC7XXX_CMDS_PER_DEVICE=253 CONFIG_AIC7XXX_RESET_DELAY_MS=5000 # CONFIG_AIC7XXX_BUILD_FIRMWARE is not set CONFIG_SCSI_DPT_I2O=y # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_IN2000 is not set # CONFIG_SCSI_AM53C974 is not set CONFIG_SCSI_MEGARAID=y # CONFIG_SCSI_BUSLOGIC is not set # CONFIG_SCSI_CPQFCTS is not set # CONFIG_SCSI_DMX3191D is not set # CONFIG_SCSI_DTC3280 is not set # CONFIG_SCSI_EATA is not set # CONFIG_SCSI_EATA_DMA is not set # CONFIG_SCSI_EATA_PIO is not set # CONFIG_SCSI_FUTURE_DOMAIN is not set # CONFIG_SCSI_GDTH is not set # CONFIG_SCSI_GENERIC_NCR5380 is not set # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_PPA is not set # CONFIG_SCSI_IMM is not set # CONFIG_SCSI_NCR53C406A is not set # CONFIG_SCSI_NCR53C7xx is not set CONFIG_SCSI_SYM53C8XX_2=y CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1 CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16 CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64 # CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set # CONFIG_SCSI_PAS16 is not set # CONFIG_SCSI_PCI2000 is not set # CONFIG_SCSI_PCI2220I is not set # CONFIG_SCSI_PSI240I is not set # CONFIG_SCSI_QLOGIC_FAS is not set # CONFIG_SCSI_QLOGIC_ISP is not set # CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_QLOGIC_1280 is not set # CONFIG_SCSI_SEAGATE is not set # CONFIG_SCSI_SIM710 is not set # CONFIG_SCSI_SYM53C416 is not set # CONFIG_SCSI_DC390T is not set # CONFIG_SCSI_T128 is not set # CONFIG_SCSI_U14_34F is not set # CONFIG_SCSI_ULTRASTOR is not set # CONFIG_SCSI_DEBUG is not set
# # Fusion MPT device support # # CONFIG_FUSION is not set # CONFIG_FUSION_BOOT is not set # CONFIG_FUSION_ISENSE is not set # CONFIG_FUSION_CTL is not set # CONFIG_FUSION_LAN is not set
# # IEEE 1394 (FireWire) support (EXPERIMENTAL) # # CONFIG_IEEE1394 is not set
# # I2O device support # CONFIG_I2O=m CONFIG_I2O_PCI=m CONFIG_I2O_BLOCK=m CONFIG_I2O_LAN=m CONFIG_I2O_SCSI=m CONFIG_I2O_PROC=m
# # Network device support # CONFIG_NETDEVICES=y
# # ARCnet devices # # CONFIG_ARCNET is not set
# # Appletalk devices # # CONFIG_APPLETALK is not set CONFIG_DUMMY=m CONFIG_BONDING=m # CONFIG_EQUALIZER is not set CONFIG_TUN=m # CONFIG_ETHERTAP is not set
# # Ethernet (10 or 100Mbit) # CONFIG_NET_ETHERNET=y # CONFIG_SUNLANCE is not set # CONFIG_HAPPYMEAL is not set # CONFIG_SUNBMAC is not set # CONFIG_SUNQE is not set # CONFIG_SUNLANCE is not set # CONFIG_SUNGEM is not set CONFIG_NET_VENDOR_3COM=y # CONFIG_EL1 is not set # CONFIG_EL2 is not set # CONFIG_ELPLUS is not set # CONFIG_EL16 is not set # CONFIG_EL3 is not set # CONFIG_3C515 is not set # CONFIG_ELMC is not set # CONFIG_ELMC_II is not set CONFIG_VORTEX=m # CONFIG_LANCE is not set # CONFIG_NET_VENDOR_SMC is not set # CONFIG_NET_VENDOR_RACAL is not set # CONFIG_AT1700 is not set # CONFIG_DEPCA is not set # CONFIG_HP100 is not set # CONFIG_NET_ISA is not set CONFIG_NET_PCI=y # CONFIG_PCNET32 is not set # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_AC3200 is not set # CONFIG_APRICOT is not set # CONFIG_CS89x0 is not set CONFIG_TULIP=m # CONFIG_TULIP_MWI is not set # CONFIG_TULIP_MMIO is not set # CONFIG_DE4X5 is not set # CONFIG_DGRS is not set # CONFIG_DM9102 is not set CONFIG_EEPRO100=m # CONFIG_LNE390 is not set # CONFIG_FEALNX is not set # CONFIG_NATSEMI is not set CONFIG_NE2K_PCI=m # CONFIG_NE3210 is not set # CONFIG_ES3210 is not set CONFIG_8139CP=m CONFIG_8139TOO=m # CONFIG_8139TOO_PIO is not set # CONFIG_8139TOO_TUNE_TWISTER is not set # CONFIG_8139TOO_8129 is not set # CONFIG_SIS900 is not set # CONFIG_EPIC100 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set # CONFIG_VIA_RHINE is not set # CONFIG_WINBOND_840 is not set # CONFIG_NET_POCKET is not set
# # Ethernet (1000 Mbit) # CONFIG_ACENIC=m # CONFIG_ACENIC_OMIT_TIGON_I is not set # CONFIG_DL2K is not set # CONFIG_MYRI_SBUS is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set CONFIG_SK98LIN=m # CONFIG_FDDI is not set # CONFIG_HIPPI is not set # CONFIG_PLIP is not set CONFIG_PPP=m CONFIG_PPP_MULTILINK=y CONFIG_PPP_FILTER=y CONFIG_PPP_ASYNC=m CONFIG_PPP_SYNC_TTY=m CONFIG_PPP_DEFLATE=m CONFIG_PPP_BSDCOMP=m CONFIG_PPPOE=m # CONFIG_SLIP is not set
# # Wireless LAN (non-hamradio) # # CONFIG_NET_RADIO is not set
# # Token Ring devices # # CONFIG_TR is not set CONFIG_NET_FC=y CONFIG_IPHASE5526=m # CONFIG_RCPCI is not set # CONFIG_SHAPER is not set
# # Wan interfaces # # CONFIG_WAN is not set
# # Amateur Radio support # # CONFIG_HAMRADIO is not set
# # IrDA (infrared) support # # CONFIG_IRDA is not set
# # ISDN subsystem # # CONFIG_ISDN is not set
# # Old CD-ROM drivers (not SCSI, not IDE) # # CONFIG_CD_NO_IDESCSI is not set
# # Input core support # CONFIG_INPUT=m CONFIG_INPUT_KEYBDEV=m CONFIG_INPUT_MOUSEDEV=m CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 CONFIG_INPUT_JOYDEV=m CONFIG_INPUT_EVDEV=m
# # Character devices # CONFIG_VT=y CONFIG_VT_CONSOLE=y CONFIG_SERIAL=y CONFIG_SERIAL_CONSOLE=y CONFIG_SERIAL_EXTENDED=y CONFIG_SERIAL_MANY_PORTS=y CONFIG_SERIAL_SHARE_IRQ=y # CONFIG_SERIAL_DETECT_IRQ is not set CONFIG_SERIAL_MULTIPORT=y # CONFIG_HUB6 is not set CONFIG_SERIAL_NONSTANDARD=y # CONFIG_COMPUTONE is not set # CONFIG_ROCKETPORT is not set CONFIG_CYCLADES=m # CONFIG_CYZ_INTR is not set # CONFIG_DIGIEPCA is not set # CONFIG_DIGI is not set # CONFIG_ESPSERIAL is not set # CONFIG_MOXA_INTELLIO is not set # CONFIG_MOXA_SMARTIO is not set # CONFIG_ISI is not set # CONFIG_SYNCLINK is not set # CONFIG_N_HDLC is not set # CONFIG_RISCOM8 is not set # CONFIG_SPECIALIX is not set # CONFIG_SX is not set # CONFIG_RIO is not set # CONFIG_STALDRV is not set CONFIG_UNIX98_PTYS=y CONFIG_UNIX98_PTY_COUNT=256 CONFIG_PRINTER=m # CONFIG_LP_CONSOLE is not set CONFIG_PPDEV=m
# # I2C support # CONFIG_I2C=m CONFIG_I2C_ALGOBIT=m CONFIG_I2C_PHILIPSPAR=m CONFIG_I2C_ELV=m CONFIG_I2C_VELLEMAN=m CONFIG_I2C_ALGOPCF=m CONFIG_I2C_ELEKTOR=m CONFIG_I2C_CHARDEV=m CONFIG_I2C_PROC=m
# # Mice # # CONFIG_BUSMOUSE is not set CONFIG_MOUSE=m CONFIG_PSMOUSE=y # CONFIG_82C710_MOUSE is not set # CONFIG_PC110_PAD is not set
# # Joysticks # # CONFIG_INPUT_GAMEPORT is not set # CONFIG_INPUT_NS558 is not set # CONFIG_INPUT_LIGHTNING is not set # CONFIG_INPUT_PCIGAME is not set # CONFIG_INPUT_CS461X is not set # CONFIG_INPUT_EMU10K1 is not set # CONFIG_INPUT_SERIO is not set # CONFIG_INPUT_SERPORT is not set # CONFIG_INPUT_ANALOG is not set # CONFIG_INPUT_A3D is not set # CONFIG_INPUT_ADI is not set # CONFIG_INPUT_COBRA is not set # CONFIG_INPUT_GF2K is not set # CONFIG_INPUT_GRIP is not set # CONFIG_INPUT_INTERACT is not set # CONFIG_INPUT_TMDC is not set # CONFIG_INPUT_SIDEWINDER is not set # CONFIG_INPUT_IFORCE_USB is not set # CONFIG_INPUT_IFORCE_232 is not set # CONFIG_INPUT_WARRIOR is not set # CONFIG_INPUT_MAGELLAN is not set # CONFIG_INPUT_SPACEORB is not set # CONFIG_INPUT_SPACEBALL is not set # CONFIG_INPUT_STINGER is not set # CONFIG_INPUT_DB9 is not set # CONFIG_INPUT_GAMECON is not set # CONFIG_INPUT_TURBOGRAFX is not set # CONFIG_QIC02_TAPE is not set
# # Watchdog Cards # CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set CONFIG_SOFT_WATCHDOG=y # CONFIG_WDT is not set # CONFIG_WDTPCI is not set # CONFIG_PCWATCHDOG is not set # CONFIG_ACQUIRE_WDT is not set # CONFIG_ADVANTECH_WDT is not set # CONFIG_IB700_WDT is not set # CONFIG_60XX_WDT is not set # CONFIG_W83877F_WDT is not set # CONFIG_MIXCOMWD is not set # CONFIG_I810_TCO is not set # CONFIG_MACHZ_WDT is not set CONFIG_INTEL_RNG=y CONFIG_NVRAM=m CONFIG_RTC=y # CONFIG_DTLK is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set # CONFIG_SONYPI is not set
# # Ftape, the floppy tape device driver # # CONFIG_FTAPE is not set CONFIG_AGP=m CONFIG_AGP_INTEL=y CONFIG_AGP_I810=y CONFIG_AGP_VIA=y CONFIG_AGP_AMD=y CONFIG_AGP_SIS=y CONFIG_AGP_ALI=y CONFIG_AGP_SWORKS=y # CONFIG_DRM is not set # CONFIG_MWAVE is not set
# # Multimedia devices # # CONFIG_VIDEO_DEV is not set
# # File systems # CONFIG_QUOTA=y CONFIG_AUTOFS_FS=m CONFIG_AUTOFS4_FS=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_ADFS_FS is not set # CONFIG_ADFS_FS_RW is not set # CONFIG_AFFS_FS is not set # CONFIG_HFS_FS is not set # CONFIG_BFS_FS is not set CONFIG_EXT3_FS=y CONFIG_JBD=y CONFIG_JBD_DEBUG=y CONFIG_FAT_FS=m CONFIG_MSDOS_FS=m # CONFIG_UMSDOS_FS is not set CONFIG_VFAT_FS=m # CONFIG_EFS_FS is not set # CONFIG_JFFS_FS is not set # CONFIG_JFFS2_FS is not set # CONFIG_CRAMFS is not set CONFIG_TMPFS=y # CONFIG_RAMFS is not set CONFIG_ISO9660_FS=m CONFIG_JOLIET=y # CONFIG_ZISOFS is not set # CONFIG_MINIX_FS is not set CONFIG_VXFS_FS=m CONFIG_NTFS_FS=m CONFIG_NTFS_RW=y # CONFIG_HPFS_FS is not set CONFIG_PROC_FS=y # CONFIG_DEVFS_FS is not set # CONFIG_DEVFS_MOUNT is not set # CONFIG_DEVFS_DEBUG is not set CONFIG_DEVPTS_FS=y # CONFIG_QNX4FS_FS is not set # CONFIG_QNX4FS_RW is not set # CONFIG_ROMFS_FS is not set CONFIG_EXT2_FS=y # CONFIG_SYSV_FS is not set # CONFIG_UDF_FS is not set # CONFIG_UDF_RW is not set # CONFIG_UFS_FS is not set # CONFIG_UFS_FS_WRITE is not set
# # Network File Systems # CONFIG_CODA_FS=m CONFIG_NFS_FS=m CONFIG_NFS_V3=y # CONFIG_ROOT_NFS is not set CONFIG_NFSD=m CONFIG_NFSD_V3=y CONFIG_SUNRPC=m CONFIG_LOCKD=m CONFIG_LOCKD_V4=y CONFIG_SMB_FS=m # CONFIG_SMB_NLS_DEFAULT is not set # CONFIG_NCP_FS is not set # CONFIG_NCPFS_PACKET_SIGNING is not set # CONFIG_NCPFS_IOCTL_LOCKING is not set # CONFIG_NCPFS_STRONG is not set # CONFIG_NCPFS_NFS_NS is not set # CONFIG_NCPFS_OS2_NS is not set # CONFIG_NCPFS_SMALLDOS is not set # CONFIG_NCPFS_NLS is not set # CONFIG_NCPFS_EXTRAS is not set # CONFIG_ZISOFS_FS is not set # CONFIG_ZLIB_FS_INFLATE is not set
# # Partition Types # CONFIG_PARTITION_ADVANCED=y # CONFIG_ACORN_PARTITION is not set # CONFIG_OSF_PARTITION is not set # CONFIG_AMIGA_PARTITION is not set # CONFIG_ATARI_PARTITION is not set # CONFIG_MAC_PARTITION is not set CONFIG_MSDOS_PARTITION=y # CONFIG_BSD_DISKLABEL is not set # CONFIG_MINIX_SUBPARTITION is not set # CONFIG_SOLARIS_X86_PARTITION is not set # CONFIG_UNIXWARE_DISKLABEL is not set CONFIG_LDM_PARTITION=y CONFIG_LDM_DEBUG=y # CONFIG_SGI_PARTITION is not set # CONFIG_ULTRIX_PARTITION is not set # CONFIG_SUN_PARTITION is not set CONFIG_SMB_NLS=y CONFIG_NLS=y
# # Native Language Support # CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_CODEPAGE_437 is not set # CONFIG_NLS_CODEPAGE_737 is not set # CONFIG_NLS_CODEPAGE_775 is not set # CONFIG_NLS_CODEPAGE_850 is not set # CONFIG_NLS_CODEPAGE_852 is not set # CONFIG_NLS_CODEPAGE_855 is not set # CONFIG_NLS_CODEPAGE_857 is not set # CONFIG_NLS_CODEPAGE_860 is not set # CONFIG_NLS_CODEPAGE_861 is not set # CONFIG_NLS_CODEPAGE_862 is not set # CONFIG_NLS_CODEPAGE_863 is not set # CONFIG_NLS_CODEPAGE_864 is not set # CONFIG_NLS_CODEPAGE_865 is not set # CONFIG_NLS_CODEPAGE_866 is not set # CONFIG_NLS_CODEPAGE_869 is not set # CONFIG_NLS_CODEPAGE_936 is not set # CONFIG_NLS_CODEPAGE_950 is not set # CONFIG_NLS_CODEPAGE_932 is not set # CONFIG_NLS_CODEPAGE_949 is not set # CONFIG_NLS_CODEPAGE_874 is not set # CONFIG_NLS_ISO8859_8 is not set # CONFIG_NLS_CODEPAGE_1251 is not set # CONFIG_NLS_ISO8859_1 is not set # CONFIG_NLS_ISO8859_2 is not set # CONFIG_NLS_ISO8859_3 is not set # CONFIG_NLS_ISO8859_4 is not set # CONFIG_NLS_ISO8859_5 is not set # CONFIG_NLS_ISO8859_6 is not set # CONFIG_NLS_ISO8859_7 is not set # CONFIG_NLS_ISO8859_9 is not set # CONFIG_NLS_ISO8859_13 is not set # CONFIG_NLS_ISO8859_14 is not set # CONFIG_NLS_ISO8859_15 is not set # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set
# # Console drivers # CONFIG_VGA_CONSOLE=y CONFIG_VIDEO_SELECT=y # CONFIG_MDA_CONSOLE is not set
# # Frame-buffer support # # CONFIG_FB is not set
# # Sound # CONFIG_SOUND=m # CONFIG_SOUND_BT878 is not set # CONFIG_SOUND_CMPCI is not set CONFIG_SOUND_EMU10K1=m CONFIG_MIDI_EMU10K1=y # CONFIG_SOUND_FUSION is not set # CONFIG_SOUND_CS4281 is not set CONFIG_SOUND_ES1370=m CONFIG_SOUND_ES1371=m # CONFIG_SOUND_ESSSOLO1 is not set # CONFIG_SOUND_MAESTRO is not set # CONFIG_SOUND_MAESTRO3 is not set CONFIG_SOUND_ICH=m # CONFIG_SOUND_RME96XX is not set # CONFIG_SOUND_SONICVIBES is not set # CONFIG_SOUND_TRIDENT is not set # CONFIG_SOUND_MSNDCLAS is not set # CONFIG_SOUND_MSNDPIN is not set CONFIG_SOUND_VIA82CXXX=m # CONFIG_MIDI_VIA82CXXX is not set CONFIG_SOUND_OSS=m CONFIG_SOUND_TRACEINIT=y # CONFIG_SOUND_DMAP is not set # CONFIG_SOUND_AD1816 is not set # CONFIG_SOUND_SGALAXY is not set # CONFIG_SOUND_ADLIB is not set # CONFIG_SOUND_ACI_MIXER is not set # CONFIG_SOUND_CS4232 is not set # CONFIG_SOUND_SSCAPE is not set # CONFIG_SOUND_GUS is not set # CONFIG_SOUND_VMIDI is not set # CONFIG_SOUND_TRIX is not set # CONFIG_SOUND_MSS is not set # CONFIG_SOUND_MPU401 is not set # CONFIG_SOUND_NM256 is not set # CONFIG_SOUND_MAD16 is not set # CONFIG_SOUND_PAS is not set # CONFIG_PAS_JOYSTICK is not set # CONFIG_SOUND_PSS is not set CONFIG_SOUND_SB=m # CONFIG_SOUND_AWE32_SYNTH is not set # CONFIG_SOUND_WAVEFRONT is not set # CONFIG_SOUND_MAUI is not set # CONFIG_SOUND_YM3812 is not set # CONFIG_SOUND_OPL3SA1 is not set # CONFIG_SOUND_OPL3SA2 is not set CONFIG_SOUND_YMFPCI=m # CONFIG_SOUND_YMFPCI_LEGACY is not set # CONFIG_SOUND_UART6850 is not set # CONFIG_SOUND_AEDSP16 is not set # CONFIG_SOUND_TVMIXER is not set
# # USB support # CONFIG_USB=m CONFIG_USB_DEBUG=y CONFIG_USB_DEVICEFS=y # CONFIG_USB_BANDWIDTH is not set # CONFIG_USB_LONG_TIMEOUT is not set CONFIG_USB_UHCI=m CONFIG_USB_UHCI_ALT=m CONFIG_USB_OHCI=m CONFIG_USB_AUDIO=m # CONFIG_USB_BLUETOOTH is not set CONFIG_USB_STORAGE=m CONFIG_USB_STORAGE_DEBUG=y # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set # CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_DPCM is not set # CONFIG_USB_STORAGE_HP8200e is not set # CONFIG_USB_STORAGE_SDDR09 is not set # CONFIG_USB_STORAGE_JUMPSHOT is not set CONFIG_USB_ACM=m CONFIG_USB_PRINTER=m CONFIG_USB_HID=m CONFIG_USB_HIDDEV=y # CONFIG_USB_KBD is not set # CONFIG_USB_MOUSE is not set # CONFIG_USB_WACOM is not set # CONFIG_USB_DC2XX is not set # CONFIG_USB_MDC800 is not set # CONFIG_USB_SCANNER is not set # CONFIG_USB_MICROTEK is not set # CONFIG_USB_HPUSBSCSI is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_KAWETH is not set # CONFIG_USB_CATC is not set # CONFIG_USB_CDCETHER is not set # CONFIG_USB_USBNET is not set # CONFIG_USB_USS720 is not set
# # USB Serial Converter support # CONFIG_USB_SERIAL=m CONFIG_USB_SERIAL_GENERIC=y # CONFIG_USB_SERIAL_BELKIN is not set # CONFIG_USB_SERIAL_WHITEHEAT is not set # CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set # CONFIG_USB_SERIAL_EMPEG is not set # CONFIG_USB_SERIAL_FTDI_SIO is not set # CONFIG_USB_SERIAL_VISOR is not set # CONFIG_USB_SERIAL_IR is not set # CONFIG_USB_SERIAL_EDGEPORT is not set # CONFIG_USB_SERIAL_KEYSPAN_PDA is not set # CONFIG_USB_SERIAL_KEYSPAN is not set # CONFIG_USB_SERIAL_KEYSPAN_USA28 is not set # CONFIG_USB_SERIAL_KEYSPAN_USA28X is not set # CONFIG_USB_SERIAL_KEYSPAN_USA28XA is not set # CONFIG_USB_SERIAL_KEYSPAN_USA28XB is not set # CONFIG_USB_SERIAL_KEYSPAN_USA19 is not set # CONFIG_USB_SERIAL_KEYSPAN_USA18X is not set # CONFIG_USB_SERIAL_KEYSPAN_USA19W is not set # CONFIG_USB_SERIAL_KEYSPAN_USA49W is not set # CONFIG_USB_SERIAL_MCT_U232 is not set # CONFIG_USB_SERIAL_PL2303 is not set # CONFIG_USB_SERIAL_CYBERJACK is not set # CONFIG_USB_SERIAL_XIRCOM is not set # CONFIG_USB_SERIAL_OMNINET is not set # CONFIG_USB_RIO500 is not set
# # Bluetooth support # # CONFIG_BLUEZ is not set
# # Kernel hacking # CONFIG_DEBUG_KERNEL=y # CONFIG_DEBUG_HIGHMEM is not set # CONFIG_DEBUG_SLAB is not set # CONFIG_DEBUG_IOVIRT is not set CONFIG_MAGIC_SYSRQ=y # CONFIG_DEBUG_SPINLOCK is not set CONFIG_DEBUG_BUGVERBOSE=y
[root@skunk ~]$ lspci -v -v -v 00:00.0 Host bridge: Relience Computer CNB20HE (rev 21) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.1 Host bridge: Relience Computer CNB20HE (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 64 set, cache line size 08
00:00.2 Host bridge: Relience Computer: Unknown device 0006 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
00:00.3 Host bridge: Relience Computer: Unknown device 0006 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
00:06.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 08) Subsystem: Hewlett-Packard Company: Unknown device 10ca Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 8 min, 56 max, 64 set, cache line size 08 Interrupt: pin A routed to IRQ 18 Region 0: Memory at cf801000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 1800 [size=64] Region 2: Memory at cf900000 (32-bit, non-prefetchable) [size=1M] Capabilities: [dc] Power Management version 2 Flags: PMEClk- AuxPwr- DSI+ D1+ D2+ PME+ Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:07.0 VGA compatible controller: ATI Technologies Inc 3D Rage IIC (rev 7a) (prog-if 00 [VGA]) Subsystem: Hewlett-Packard Company: Unknown device 10c4 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 8 min, 66 set, cache line size 08 Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=16M] Region 1: I/O ports at 1400 [size=256] Region 2: Memory at cf802000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [5c] Power Management version 1 Flags: PMEClk- AuxPwr- DSI- D1- D2- PME- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.0 ISA bridge: Relience Computer: Unknown device 0200 (rev 4f) Subsystem: Relience Computer: Unknown device 0200 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 set
00:0f.1 IDE interface: Relience Computer: Unknown device 0211 (prog-if 8a [Master SecP PriP]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 set Region 4: I/O ports at 1840 [size=16]
01:03.0 PCI bridge: Digital Equipment Corporation DECchip 21154 (rev 05) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B+ Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 set, cache line size 08 Bus: primary=01, secondary=02, subordinate=02, sec-latency=68 I/O behind bridge: 00002000-00002fff Memory behind bridge: d2000000-d3ffffff Prefetchable memory behind bridge: 00000000d8000000-00000000dbf00000 BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [dc] Power Management version 1 Flags: PMEClk- AuxPwr- DSI- D1- D2- PME- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:08.0 RAID bus controller: Mylex Corporation: Unknown device ba56 Subsystem: Mylex Corporation: Unknown device 0040 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 set, cache line size 08 Interrupt: pin A routed to IRQ 20 Region 0: Memory at d2000000 (32-bit, non-prefetchable) [size=32M] Region 1: I/O ports at 2000 [size=128] Region 2: Memory at d8000000 (64-bit, prefetchable) [size=64M] Expansion ROM at <unassigned> [disabled] [size=1M] Capabilities: [70] Power Management version 1 Flags: PMEClk- AuxPwr- DSI- D1- D2- PME- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:02.0 System peripheral: Hewlett-Packard Company: Unknown device 1219 (rev 0b) Subsystem: Hewlett-Packard Company: Unknown device 0001 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 4000 [size=256]
04:02.1 Class 0c06: Hewlett-Packard Company: Unknown device 121a (rev 0b) Subsystem: Hewlett-Packard Company: Unknown device 0001 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 17 Region 0: I/O ports at 4400 [size=256]
04:03.0 PCI bridge: Intel Corporation: Unknown device 0964 (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 set, cache line size 08 Bus: primary=04, secondary=05, subordinate=05, sec-latency=64 I/O behind bridge: 00005000-00005fff Memory behind bridge: dc800000-dc8fffff Prefetchable memory behind bridge: fff00000-000fffff BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [68] Power Management version 2 Flags: PMEClk- AuxPwr- DSI- D1- D2- PME- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:03.1 SCSI storage controller: Intel Corporation 80960RP [i960RP Microprocessor] (rev 01) Subsystem: Hewlett-Packard Company: Unknown device 10cc Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B+ Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 set, cache line size 08 Interrupt: pin A routed to IRQ 21 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M] Expansion ROM at <unassigned> [disabled] [size=32K] Capabilities: [80] Power Management version 2 Flags: PMEClk- AuxPwr- DSI- D1- D2- PME- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:04.0 Ethernet controller: Syskonnect (Schneider & Koch) Gigabit Ethernet (rev 12) Subsystem: Syskonnect (Schneider & Koch) SK-9843 (1000Base-SX single link) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 23 min, 31 max, 64 set, cache line size 08 Interrupt: pin A routed to IRQ 22 Region 0: Memory at dc808000 (32-bit, non-prefetchable) [size=16K] Region 1: I/O ports at 5000 [size=256] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [48] Power Management version 1 Flags: PMEClk- AuxPwr- DSI- D1- D2- PME- Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [50] Vital Product Data
05:08.0 System peripheral: Hewlett-Packard Company: Unknown device 10c1 (rev a0) Subsystem: Hewlett-Packard Company: Unknown device 0001 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Region 0: Memory at dc800000 (32-bit, non-prefetchable) [size=32K]
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/