Re: usb interface to Toshiba PDR-M4 cam hasn't worked since 2.4.5

[Johannes Erdfelt]

On Wed, Oct 24, 2001, [e-mail] <[e-mail]> wrote:
> If there's a usb list this would be more appropriate in, please let me
> know.

[e-mail]

I thought we did a good job advertising it. Where did you look?

> I have a Toshiba PDR-M4 digital camera with USB interface, which
> appeared as a scsi device attached with usb-storage in linux-2.4.5, but
> hasn't worked in any kernel since then.  Here's a snippet from dmesg from
> 2.4.5, with a successful negotiation with the camera (and its 128MB smart
> media card).  The usbcore, usb-uhci, usb-storage, and sd modules are
> already loaded at this point.
> 
>  usb-uhci.c: v1.251 Georg Acher, Deti Fliegl, Thomas Sailer, Roman
> Weissgaerber
>  usb-uhci.c: USB Universal Host Controller Interface driver
>  hub.c: USB new device connect on bus1/1, assigned device number 2
>  usb.c: USB device 2 (vend/prod 0x1132/0x4331) is not claimed by any
> active driver.
>  Initializing USB Mass Storage driver...
>  usb.c: registered new driver usb-storage
>  usb-uhci.c: interrupt, status 2, frame# 1366
>  scsi0 : SCSI emulation for USB Mass Storage devices
>    Vendor: TOSHIBA   Model: PDR               Rev: 1.00
>    Type:   Direct-Access                      ANSI SCSI revision: 02
>  Detected scsi removable disk sda at scsi0, channel 0, id 0, lun 0
>  SCSI device sda: 256000 512-byte hdwr sectors (131 MB)
>  sda: Write Protect is off
>   /dev/scsi/host0/bus0/target0/lun0: p1
>  WARNING: USB Mass Storage data integrity not assured
>  USB Mass Storage device found at 2
>  USB Mass Storage support registered.
> 
> And here's dmesg output from the same operation with 2.4.13:
> 
>    * turn camera to 'data' mode *
>  hub.c: port 2 connection change
>  hub.c: port 2, portstatus 101, change 1, 12 Mb/s
>  hub.c: port 2, portstatus 103, change 0, 12 Mb/s
>  hub.c: USB new device connect on bus1/2, assigned device number 6
>    * 4-second pause *
>  usb_control/bulk_msg: timeout
>  usb.c: USB device not accepting new address=6 (error=-110)
>  hub.c: port 2, portstatus 103, change 0, 12 Mb/s
>  hub.c: USB new device connect on bus1/2, assigned device number 7
>    * 4-second pause *
>  usb_control/bulk_msg: timeout
>  usb.c: USB device not accepting new address=7 (error=-110)
> 
> And no more messages until I turn off or disconnect the camera.  It
> never procedes to initialize usb-storage on this device.
> 
> The same errors ("usb_control/bulk_msg: timeout" and "USB device not
> accepting new address=7 (error=-110)") have occurred with every kernel
> since 2.4.6 when I attempt to attach this camera.  I don't believe it
> ever worked with 2.2.18/.19 either, but it did work with 2.2.17 with
> Alan's usb patches.

Have you tried using the alternate UHCI driver?

JE