It's been working very well here for some time, on an ASUS A7M266
motherboard. The output from lspci is attached.
On Tue, Jul 24, 2001 at 09:43:21AM -0600, Jeff Hartmann wrote:
> I have a pre production Tyan mb that I tested things on. It seemed
> to work just fine with agp_try_unsupported=1. Please test it with
> agp_try_unsupported on an actual production system to make sure, but
> if it works just send me the output of lspci -vvv and I'll put it in
> the kernel.
>
> -Jeff
--T4sUOijqQbZv57TR
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="lspci.out"
00:00.0 Host bridge: Advanced Micro Devices [AMD]: Unknown device 700e (rev 13)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at f7800000 (32-bit, prefetchable) [size=4K]
Region 2: I/O ports at e000 [disabled] [size=4]
Capabilities: [a0] AGP version 2.0
Status: RQ=15 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Advanced Micro Devices [AMD]: Unknown device 700f (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000dfff
Memory behind bridge: f2800000-f3dfffff
Prefetchable memory behind bridge: f3f00000-f77fffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: Asustek Computer, Inc.: Unknown device 8040
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 4: I/O ports at d800 [disabled] [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 14
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 14
Region 4: I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.4 Non-VGA unclassified device: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: Asustek Computer, Inc.: Unknown device 8040
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:05.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: Asustek Computer, Inc.: Unknown device 80e2
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at a400 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Serial controller: Siig Inc CyberSerial (1-port) 16550 (prog-if 02 [16550])
Subsystem: Siig Inc CyberSerial (1-port) 16550
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 14
Region 0: I/O ports at a000 [size=8]
Capabilities: [a0] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 SCSI storage controller: Adaptec AIC-7881U (rev 01)
Subsystem: Adaptec AHA-2940UW SCSI Host Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 15
Region 0: I/O ports at 9800 [disabled] [size=256]
Region 1: Memory at f2000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 Ethernet controller: 3Com Corporation 3c905 100BaseTX [Boomerang]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 9400 [size=64]
Expansion ROM at <unassigned> [disabled] [size=64K]
00:0d.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 05)
Subsystem: Creative Labs CT4760 SBLive!
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 14
Region 0: I/O ports at 9000 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.1 Input device controller: Creative Labs SB Live! (rev 05)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at 8800 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:05.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 04) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G400 Dual Head Max
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at f3000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at f2800000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at f3ff0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
--T4sUOijqQbZv57TR--
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/