I think Ted is trying to get the driver to heuristically detect
some serial boards/modems, in an effort to reduce the
table of pci serial devices which is large.
The "Redundant" message itself is informational and
does not affect the operation of the device.
As for the ports, the boot message says ttyS04 but devfs
really creates ttyS4. You should use that. It seems likely that
your attempt to create ttyS4 on your own overwrote the real
ttyS4. ttyS4 should be created automatically for you.
You can't force ttyS2 to be the device by using setserial;
setserial merely informs the driver of hardware that is
already there. Your device is at ttyS4, not ttyS2. Some other
device is already at ttyS2. Probably it's a reserved slot for
the fourth standard port.
..Stu
----- Original Message -----
From: "Michael Stutz" <stutz@dsl.org>
To: <linux-kernel@vger.kernel.org>
Sent: June 28, 2001 12:29 p
Subject: Linux 2.4.5: serial problems with ASUS A7PRO PCI (VIA VT82C686A)
>
> I'm getting a "Redundant entry in serial pci_table" message on 2.4.5
> with a PCI modem (US Robotics/3Com 56K FaxModem Model 5610) on my ASUS
> A7PRO PCI133/VC133 (VIA VT8363 / VIA VT82C686A) motherboard.
>
> On Linux 2.2.17 (Debian 2.2) the modem works fine but I had problems
> where attempts to use devices on my PCI SCSI card (BusLogic BT-958)
> froze the system, and playing audio CDs on the IDE CD-ROM drive got
> sense_key errors (both seemed to work swell in 2.4.5).
>
> Normally, the modem is at /dev/ttyS2, irq 5; with 2.4.5 it insists on
> calling it "ttyS04" (below) and it's unusable... when I try to use
> setserial to give the proper values to /dev/ttyS2, I get: "ttyS2: LSR
> safety check engaged!"; I tried making a /dev/ttyS4 device but that
> didn't work either... I popped out the ethernet card (D-Link
> DFE-530TX+) and the extra 2 USB ports but that didn't help; I'm back
> to 2.2.17 temporarily, just so I can have connectivity to send this
> mail. All the relevant info follows, I hope; I'd appreciate any advice
> or assistance with this ...
>
>
> From dmesg:
> ----------------------------------
> PCI: PCI BIOS revision 2.10 entry at 0xf1150, last bus=1
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> Unknown bridge resource 0: assuming transparent
> PCI: Using IRQ router VIA [1106/0686] at 00:04.0
> Found VT82C686A, not applying VIA latency patch.
> ...
> Serial driver version 5.05a (2001-03-20) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> PCI: Found IRQ 12 for device 00:0a.0
> Redundant entry in serial pci_table. Please send the output of
> lspci -vv, this message (4793,4104,4793,170)
> and the manufacturer and name of serial board or modem board
> to serial-pci-info@lists.sourceforge.net.
> ttyS04 at port 0xa400 (irq = 12) is a 16550A
> block: queued sectors max/low 170002kB/56667kB, 512 slots per queue
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
> VP_IDE: IDE controller on PCI bus 00 dev 21
> VP_IDE: chipset revision 16
> VP_IDE: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
> ----------------------------------
>
>
> lspci -vv:
> ----------------------------------
> 00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0305 (rev 03)
> Subsystem: Asustek Computer, Inc.: Unknown device 8033
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0 set
> Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
> Capabilities: [a0] AGP version 2.0
> Status: RQ=31 SBA+ 64bit- FW- Rate=421
> Command: RQ=0 SBA- AGP- 64bit- FW- Rate=
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device 8305 (prog-if
00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0 set
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> Memory behind bridge: e0800000-e1dfffff
> Prefetchable memory behind bridge: e1f00000-e3ffffff
> BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- AuxPwr- DSI+ D1+ D2- PME-
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super] (rev
22)
> Subsystem: Asustek Computer, Inc.: Unknown device 8033
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 set
>
> 00:04.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev
10) (prog-if 8a [Master SecP PriP])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 set
> Region 4: I/O ports at d800 [size=16]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.3 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10)
(prog-if 00 [UHCI])
> Subsystem: Unknown device 0925:1234
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 set, cache line size 08
> Interrupt: pin D routed to IRQ 5
> Region 4: I/O ports at d000 [size=32]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
(rev 30)
> Subsystem: Asustek Computer, Inc.: Unknown device 8033
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin ? routed to IRQ 9
> Capabilities: [68] Power Management version 2
> Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0a.0 Serial controller: US Robotics/3Com 56K FaxModem Model 5610 (rev
01) (prog-if 02 [16550])
> Subsystem: US Robotics/3Com: Unknown device 00aa
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 12
> Region 0: I/O ports at a400 [size=8]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- AuxPwr- DSI- D1- D2+ PME+
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
> 00:0b.0 Multimedia audio controller: Ensoniq ES1370 [AudioPCI]
> Subsystem: Unknown device 4942:4c4c
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
> Latency: 12 min, 128 max, 32 set
> Interrupt: pin A routed to IRQ 10
> Region 0: I/O ports at a000 [size=64]
>
> 00:0c.0 SCSI storage controller: BusLogic BT-946C (BA80C30) [MultiMaster
10] (rev 08)
> Subsystem: BusLogic: Unknown device 1040
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
> Latency: 8 min, 8 max, 32 set, cache line size 08
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at 9800 [size=4]
> Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=4K]
> Expansion ROM at <unassigned> [disabled] [size=32K]
>
> 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev
04) (prog-if 00 [VGA])
> Subsystem: Matrox Graphics, Inc. Millennium G400 32Mb SGRAM
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
> Latency: 16 min, 32 max, 64 set, cache line size 08
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at e2000000 (32-bit, prefetchable) [size=32M]
> Region 1: Memory at e1000000 (32-bit, non-prefetchable) [size=16K]
> Region 2: Memory at e0800000 (32-bit, non-prefetchable) [size=8M]
> Expansion ROM at e1ff0000 [disabled] [size=64K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- AuxPwr- DSI+ D1- D2- PME-
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [f0] AGP version 2.0
> Status: RQ=31 SBA+ 64bit- FW- Rate=421
> Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=1
> ----------------------------------
>
>
> /proc/pci:
> ----------------------------------
> PCI devices found:
> Bus 0, device 0, function 0:
> Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 3).
> Prefetchable 32 bit memory at 0xe4000000 [0xe7ffffff].
> Bus 0, device 1, function 0:
> PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (rev
0).
> Master Capable. No bursts. Min Gnt=8.
> Bus 0, device 4, function 0:
> ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev
34).
> Bus 0, device 4, function 1:
> IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 16).
> Master Capable. Latency=32.
> I/O at 0xd800 [0xd80f].
> Bus 0, device 4, function 3:
> USB Controller: VIA Technologies, Inc. UHCI USB (rev 16).
> IRQ 5.
> Master Capable. Latency=32.
> I/O at 0xd000 [0xd01f].
> Bus 0, device 4, function 4:
> Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev
48).
> IRQ 9.
> Bus 0, device 10, function 0:
> Serial controller: US Robotics/3Com 56K FaxModem Model 5610 (rev 1).
> IRQ 12.
> I/O at 0xa400 [0xa407].
> Bus 0, device 11, function 0:
> Multimedia audio controller: Ensoniq ES1370 [AudioPCI] (rev 0).
> IRQ 10.
> Master Capable. Latency=32. Min Gnt=12.Max Lat=128.
> I/O at 0xa000 [0xa03f].
> Bus 0, device 12, function 0:
> SCSI storage controller: BusLogic BT-946C (BA80C30) [MultiMaster 10]
(rev 8).
> IRQ 11.
> Master Capable. Latency=32. Min Gnt=8.Max Lat=8.
> I/O at 0x9800 [0x9803].
> Non-prefetchable 32 bit memory at 0xe0000000 [0xe0000fff].
> Bus 1, device 0, function 0:
> VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 4).
> IRQ 11.
> Master Capable. Latency=64. Min Gnt=16.Max Lat=32.
> Prefetchable 32 bit memory at 0xe2000000 [0xe3ffffff].
> Non-prefetchable 32 bit memory at 0xe1000000 [0xe1003fff].
> Non-prefetchable 32 bit memory at 0xe0800000 [0xe0ffffff].
> ----------------------------------
>
>
> /proc/ioports:
> ----------------------------------
> 0000-001f : dma1
> 0020-003f : pic1
> 0040-005f : timer
> 0060-006f : keyboard
> 0080-008f : dma page reg
> 00a0-00bf : pic2
> 00c0-00df : dma2
> 00f0-00ff : fpu
> 0170-0177 : ide1
> 01f0-01f7 : ide0
> 02f8-02ff : serial(auto)
> 0376-0376 : ide1
> 03c0-03df : vga+
> 03e8-03ef : serial(set)
> 03f6-03f6 : ide0
> 03f8-03ff : serial(auto)
> 0cf8-0cff : PCI conf1
> 9800-9803 : BusLogic BT-946C (BA80C30) [MultiMaster 10]
> 9800-9803 : BusLogic BT-958
> a000-a03f : Ensoniq ES1370 [AudioPCI]
> a400-a407 : US Robotics/3Com 56K FaxModem Model 5610
> a400-a407 : serial(auto)
> d000-d01f : VIA Technologies, Inc. UHCI USB
> d800-d80f : VIA Technologies, Inc. Bus Master IDE
> d800-d807 : ide0
> d808-d80f : ide1
> e400-e4ff : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
> e800-e80f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
> ----------------------------------
>
>
> /proc/iomem:
> ----------------------------------
> 00000000-0009fbff : System RAM
> 0009fc00-0009ffff : reserved
> 000a0000-000bffff : Video RAM area
> 000c0000-000c7fff : Video ROM
> 000c8000-000c87ff : Extension ROM
> 000f0000-000fffff : System ROM
> 00100000-0ffebfff : System RAM
> 00100000-001c58e3 : Kernel code
> 001c58e4-0020911f : Kernel data
> 0ffec000-0ffeefff : ACPI Tables
> 0ffef000-0fffefff : reserved
> 0ffff000-0fffffff : ACPI Non-volatile Storage
> e0000000-e0000fff : BusLogic BT-946C (BA80C30) [MultiMaster 10]
> e0800000-e1dfffff : PCI Bus #01
> e0800000-e0ffffff : Matrox Graphics, Inc. MGA G400 AGP
> e1000000-e1003fff : Matrox Graphics, Inc. MGA G400 AGP
> e1f00000-e3ffffff : PCI Bus #01
> e2000000-e3ffffff : Matrox Graphics, Inc. MGA G400 AGP
> e4000000-e7ffffff : VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
> ffff0000-ffffffff : reserved
> ----------------------------------
>
>
> /proc/interrupts:
> ----------------------------------
> CPU0
> 0: 75999 XT-PIC timer
> 1: 4935 XT-PIC keyboard
> 2: 0 XT-PIC cascade
> 11: 37 XT-PIC BusLogic BT-958
> 12: 0 XT-PIC PS/2 Mouse
> 14: 62070 XT-PIC ide0
> 15: 5 XT-PIC ide1
> NMI: 0
> ERR: 0
> ----------------------------------
>
>
>
> /usr/src/linux/.config:
>
> #
> # Automatically generated make config: don't edit
> #
> CONFIG_X86=y
> CONFIG_ISA=y
> # CONFIG_SBUS is not set
> CONFIG_UID16=y
>
> #
> # Code maturity level options
> #
> CONFIG_EXPERIMENTAL=y
>
> #
> # Loadable module support
> #
> CONFIG_MODULES=y
> CONFIG_MODVERSIONS=y
> CONFIG_KMOD=y
>
> #
> # Processor type and features
> #
> # CONFIG_M386 is not set
> # CONFIG_M486 is not set
> # CONFIG_M586 is not set
> # CONFIG_M586TSC is not set
> # CONFIG_M586MMX is not set
> # CONFIG_M686 is not set
> # CONFIG_MPENTIUMIII is not set
> # CONFIG_MPENTIUM4 is not set
> # CONFIG_MK6 is not set
> CONFIG_MK7=y
> # CONFIG_MCRUSOE is not set
> # CONFIG_MWINCHIPC6 is not set
> # CONFIG_MWINCHIP2 is not set
> # CONFIG_MWINCHIP3D is not set
> # CONFIG_MCYRIXIII is not set
> CONFIG_X86_WP_WORKS_OK=y
> CONFIG_X86_INVLPG=y
> CONFIG_X86_CMPXCHG=y
> CONFIG_X86_XADD=y
> CONFIG_X86_BSWAP=y
> CONFIG_X86_POPAD_OK=y
> # CONFIG_RWSEM_GENERIC_SPINLOCK is not set
> CONFIG_RWSEM_XCHGADD_ALGORITHM=y
> CONFIG_X86_L1_CACHE_SHIFT=6
> CONFIG_X86_TSC=y
> CONFIG_X86_GOOD_APIC=y
> CONFIG_X86_USE_3DNOW=y
> CONFIG_X86_PGE=y
> CONFIG_X86_USE_PPRO_CHECKSUM=y
> # CONFIG_TOSHIBA is not set
> # CONFIG_MICROCODE is not set
> # CONFIG_X86_MSR is not set
> # CONFIG_X86_CPUID is not set
> CONFIG_NOHIGHMEM=y
> # CONFIG_HIGHMEM4G is not set
> # CONFIG_HIGHMEM64G is not set
> # CONFIG_MATH_EMULATION is not set
> CONFIG_MTRR=y
> # CONFIG_SMP is not set
> # CONFIG_X86_UP_IOAPIC is not set
>
> #
> # General setup
> #
> CONFIG_NET=y
> # CONFIG_VISWS is not set
> CONFIG_PCI=y
> # CONFIG_PCI_GOBIOS is not set
> # CONFIG_PCI_GODIRECT is not set
> CONFIG_PCI_GOANY=y
> CONFIG_PCI_BIOS=y
> CONFIG_PCI_DIRECT=y
> CONFIG_PCI_NAMES=y
> # CONFIG_EISA is not set
> # CONFIG_MCA is not set
> # CONFIG_HOTPLUG is not set
> # CONFIG_PCMCIA is not set
> CONFIG_SYSVIPC=y
> CONFIG_BSD_PROCESS_ACCT=y
> CONFIG_SYSCTL=y
> CONFIG_KCORE_ELF=y
> # CONFIG_KCORE_AOUT is not set
> CONFIG_BINFMT_AOUT=y
> CONFIG_BINFMT_ELF=y
> CONFIG_BINFMT_MISC=m
> CONFIG_PM=y
> # CONFIG_ACPI is not set
> # CONFIG_APM is not set
>
> #
> # Memory Technology Devices (MTD)
> #
> # CONFIG_MTD is not set
>
> #
> # Parallel port support
> #
> CONFIG_PARPORT=m
> CONFIG_PARPORT_PC=m
> # CONFIG_PARPORT_PC_FIFO is not set
> # CONFIG_PARPORT_PC_SUPERIO is not set
> # CONFIG_PARPORT_AMIGA is not set
> # CONFIG_PARPORT_MFC3 is not set
> # CONFIG_PARPORT_ATARI is not set
> # CONFIG_PARPORT_SUNBPP is not set
> # CONFIG_PARPORT_OTHER is not set
> CONFIG_PARPORT_1284=y
>
> #
> # Plug and Play configuration
> #
> # CONFIG_PNP is not set
> # CONFIG_ISAPNP is not set
>
> #
> # Block devices
> #
> CONFIG_BLK_DEV_FD=y
> # CONFIG_BLK_DEV_XD is not set
> # CONFIG_PARIDE is not set
> # CONFIG_BLK_CPQ_DA is not set
> # CONFIG_BLK_CPQ_CISS_DA is not set
> # CONFIG_BLK_DEV_DAC960 is not set
> CONFIG_BLK_DEV_LOOP=m
> # CONFIG_BLK_DEV_NBD is not set
> # CONFIG_BLK_DEV_RAM is not set
> # CONFIG_BLK_DEV_INITRD is not set
>
> #
> # Multi-device support (RAID and LVM)
> #
> # CONFIG_MD is not set
> # CONFIG_BLK_DEV_MD is not set
> # CONFIG_MD_LINEAR is not set
> # CONFIG_MD_RAID0 is not set
> # CONFIG_MD_RAID1 is not set
> # CONFIG_MD_RAID5 is not set
> # CONFIG_BLK_DEV_LVM is not set
>
> #
> # Networking options
> #
> CONFIG_PACKET=y
> # CONFIG_PACKET_MMAP is not set
> # CONFIG_NETLINK is not set
> # CONFIG_NETFILTER is not set
> # CONFIG_FILTER is not set
> CONFIG_UNIX=y
> CONFIG_INET=y
> # CONFIG_IP_MULTICAST is not set
> # CONFIG_IP_ADVANCED_ROUTER is not set
> # CONFIG_IP_PNP is not set
> # CONFIG_NET_IPIP is not set
> # CONFIG_NET_IPGRE is not set
> # CONFIG_INET_ECN is not set
> # CONFIG_SYN_COOKIES is not set
> # CONFIG_IPV6 is not set
> # CONFIG_KHTTPD is not set
> # CONFIG_ATM is not set
>
> #
> #
> #
> # CONFIG_IPX is not set
> # CONFIG_ATALK is not set
> # CONFIG_DECNET is not set
> # CONFIG_BRIDGE is not set
> # CONFIG_X25 is not set
> # CONFIG_LAPB is not set
> # CONFIG_LLC is not set
> # CONFIG_NET_DIVERT is not set
> # CONFIG_ECONET is not set
> # CONFIG_WAN_ROUTER is not set
> # CONFIG_NET_FASTROUTE is not set
> # CONFIG_NET_HW_FLOWCONTROL is not set
>
> #
> # QoS and/or fair queueing
> #
> # CONFIG_NET_SCHED is not set
>
> #
> # Telephony Support
> #
> # CONFIG_PHONE is not set
> # CONFIG_PHONE_IXJ is not set
>
> #
> # ATA/IDE/MFM/RLL support
> #
> CONFIG_IDE=y
>
> #
> # IDE, ATA and ATAPI Block devices
> #
> CONFIG_BLK_DEV_IDE=y
>
> #
> # Please see Documentation/ide.txt for help/info on IDE drives
> #
> # CONFIG_BLK_DEV_HD_IDE is not set
> # CONFIG_BLK_DEV_HD is not set
> CONFIG_BLK_DEV_IDEDISK=y
> # CONFIG_IDEDISK_MULTI_MODE is not set
> # CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
> # CONFIG_BLK_DEV_IDEDISK_FUJITSU is not set
> # CONFIG_BLK_DEV_IDEDISK_IBM is not set
> # CONFIG_BLK_DEV_IDEDISK_MAXTOR is not set
> # CONFIG_BLK_DEV_IDEDISK_QUANTUM is not set
> # CONFIG_BLK_DEV_IDEDISK_SEAGATE is not set
> # CONFIG_BLK_DEV_IDEDISK_WD is not set
> # CONFIG_BLK_DEV_COMMERIAL is not set
> # CONFIG_BLK_DEV_TIVO is not set
> # CONFIG_BLK_DEV_IDECS is not set
> CONFIG_BLK_DEV_IDECD=y
> # CONFIG_BLK_DEV_IDETAPE is not set
> # CONFIG_BLK_DEV_IDEFLOPPY is not set
> # CONFIG_BLK_DEV_IDESCSI is not set
>
> #
> # IDE chipset support/bugfixes
> #
> # CONFIG_BLK_DEV_CMD640 is not set
> # CONFIG_BLK_DEV_CMD640_ENHANCED is not set
> # CONFIG_BLK_DEV_ISAPNP is not set
> # CONFIG_BLK_DEV_RZ1000 is not set
> CONFIG_BLK_DEV_IDEPCI=y
> CONFIG_IDEPCI_SHARE_IRQ=y
> CONFIG_BLK_DEV_IDEDMA_PCI=y
> # CONFIG_BLK_DEV_OFFBOARD is not set
> # CONFIG_IDEDMA_PCI_AUTO is not set
> CONFIG_BLK_DEV_IDEDMA=y
> # CONFIG_IDEDMA_PCI_WIP is not set
> # CONFIG_IDEDMA_NEW_DRIVE_LISTINGS is not set
> # CONFIG_BLK_DEV_AEC62XX is not set
> # CONFIG_AEC62XX_TUNING is not set
> # CONFIG_BLK_DEV_ALI15X3 is not set
> # CONFIG_WDC_ALI15X3 is not set
> # CONFIG_BLK_DEV_AMD7409 is not set
> # CONFIG_AMD7409_OVERRIDE is not set
> # CONFIG_BLK_DEV_CMD64X is not set
> # CONFIG_BLK_DEV_CY82C693 is not set
> # CONFIG_BLK_DEV_CS5530 is not set
> # CONFIG_BLK_DEV_HPT34X is not set
> # CONFIG_HPT34X_AUTODMA is not set
> # CONFIG_BLK_DEV_HPT366 is not set
> # CONFIG_BLK_DEV_PIIX is not set
> # CONFIG_PIIX_TUNING is not set
> # CONFIG_BLK_DEV_NS87415 is not set
> # CONFIG_BLK_DEV_OPTI621 is not set
> # CONFIG_BLK_DEV_PDC202XX is not set
> # CONFIG_PDC202XX_BURST is not set
> # CONFIG_BLK_DEV_OSB4 is not set
> # CONFIG_BLK_DEV_SIS5513 is not set
> # CONFIG_BLK_DEV_SLC90E66 is not set
> # CONFIG_BLK_DEV_TRM290 is not set
> # CONFIG_BLK_DEV_VIA82CXXX is not set
> # CONFIG_IDE_CHIPSETS is not set
> # CONFIG_IDEDMA_AUTO is not set
> # CONFIG_IDEDMA_IVB is not set
> # CONFIG_DMA_NONPCI is not set
> # CONFIG_BLK_DEV_IDE_MODES is not set
>
> #
> # SCSI support
> #
> CONFIG_SCSI=m
>
> #
> # SCSI support type (disk, tape, CD-ROM)
> #
> CONFIG_BLK_DEV_SD=m
> CONFIG_SD_EXTRA_DEVS=40
> # CONFIG_CHR_DEV_ST is not set
> # CONFIG_CHR_DEV_OSST is not set
> CONFIG_BLK_DEV_SR=m
> # CONFIG_BLK_DEV_SR_VENDOR is not set
> CONFIG_SR_EXTRA_DEVS=2
> CONFIG_CHR_DEV_SG=m
>
> #
> # Some SCSI devices (e.g. CD jukebox) support multiple LUNs
> #
> CONFIG_SCSI_DEBUG_QUEUES=y
> # CONFIG_SCSI_MULTI_LUN is not set
> CONFIG_SCSI_CONSTANTS=y
> CONFIG_SCSI_LOGGING=y
>
> #
> # SCSI low-level drivers
> #
> # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
> # CONFIG_SCSI_7000FASST is not set
> # CONFIG_SCSI_ACARD is not set
> # CONFIG_SCSI_AHA152X is not set
> # CONFIG_SCSI_AHA1542 is not set
> # CONFIG_SCSI_AHA1740 is not set
> # CONFIG_SCSI_AIC7XXX is not set
> # CONFIG_SCSI_AIC7XXX_OLD is not set
> # CONFIG_SCSI_ADVANSYS is not set
> # CONFIG_SCSI_IN2000 is not set
> # CONFIG_SCSI_AM53C974 is not set
> # CONFIG_SCSI_MEGARAID is not set
> CONFIG_SCSI_BUSLOGIC=m
> # CONFIG_SCSI_OMIT_FLASHPOINT is not set
> # CONFIG_SCSI_CPQFCTS is not set
> # CONFIG_SCSI_DMX3191D is not set
> # CONFIG_SCSI_DTC3280 is not set
> # CONFIG_SCSI_EATA is not set
> # CONFIG_SCSI_EATA_DMA is not set
> # CONFIG_SCSI_EATA_PIO is not set
> # CONFIG_SCSI_FUTURE_DOMAIN is not set
> # CONFIG_SCSI_GDTH is not set
> # CONFIG_SCSI_GENERIC_NCR5380 is not set
> # CONFIG_SCSI_IPS is not set
> # CONFIG_SCSI_INITIO is not set
> # CONFIG_SCSI_INIA100 is not set
> # CONFIG_SCSI_PPA is not set
> # CONFIG_SCSI_IMM is not set
> # CONFIG_SCSI_NCR53C406A is not set
> # CONFIG_SCSI_NCR53C7xx is not set
> # CONFIG_SCSI_NCR53C8XX is not set
> # CONFIG_SCSI_SYM53C8XX is not set
> # CONFIG_SCSI_PAS16 is not set
> # CONFIG_SCSI_PCI2000 is not set
> # CONFIG_SCSI_PCI2220I is not set
> # CONFIG_SCSI_PSI240I is not set
> # CONFIG_SCSI_QLOGIC_FAS is not set
> # CONFIG_SCSI_QLOGIC_ISP is not set
> # CONFIG_SCSI_QLOGIC_FC is not set
> # CONFIG_SCSI_QLOGIC_1280 is not set
> # CONFIG_SCSI_SEAGATE is not set
> # CONFIG_SCSI_SIM710 is not set
> # CONFIG_SCSI_SYM53C416 is not set
> # CONFIG_SCSI_DC390T is not set
> # CONFIG_SCSI_T128 is not set
> # CONFIG_SCSI_U14_34F is not set
> # CONFIG_SCSI_ULTRASTOR is not set
> # CONFIG_SCSI_DEBUG is not set
>
> #
> # IEEE 1394 (FireWire) support
> #
> # CONFIG_IEEE1394 is not set
>
> #
> # I2O device support
> #
> # CONFIG_I2O is not set
> # CONFIG_I2O_PCI is not set
> # CONFIG_I2O_BLOCK is not set
> # CONFIG_I2O_LAN is not set
> # CONFIG_I2O_SCSI is not set
> # CONFIG_I2O_PROC is not set
>
> #
> # Network device support
> #
> CONFIG_NETDEVICES=y
>
> #
> # ARCnet devices
> #
> # CONFIG_ARCNET is not set
> CONFIG_DUMMY=m
> # CONFIG_BONDING is not set
> # CONFIG_EQUALIZER is not set
> # CONFIG_TUN is not set
> # CONFIG_NET_SB1000 is not set
>
> #
> # Ethernet (10 or 100Mbit)
> #
> CONFIG_NET_ETHERNET=y
> # CONFIG_NET_VENDOR_3COM is not set
> # CONFIG_LANCE is not set
> # CONFIG_NET_VENDOR_SMC is not set
> # CONFIG_NET_VENDOR_RACAL is not set
> # CONFIG_AT1700 is not set
> # CONFIG_DEPCA is not set
> # CONFIG_HP100 is not set
> # CONFIG_NET_ISA is not set
> CONFIG_NET_PCI=y
> # CONFIG_PCNET32 is not set
> # CONFIG_ADAPTEC_STARFIRE is not set
> # CONFIG_AC3200 is not set
> # CONFIG_APRICOT is not set
> # CONFIG_CS89x0 is not set
> # CONFIG_TULIP is not set
> # CONFIG_DE4X5 is not set
> # CONFIG_DGRS is not set
> # CONFIG_DM9102 is not set
> # CONFIG_EEPRO100 is not set
> # CONFIG_EEPRO100_PM is not set
> # CONFIG_LNE390 is not set
> # CONFIG_FEALNX is not set
> # CONFIG_NATSEMI is not set
> # CONFIG_NE2K_PCI is not set
> # CONFIG_NE3210 is not set
> # CONFIG_ES3210 is not set
> CONFIG_8139TOO=m
> # CONFIG_8139TOO_PIO is not set
> # CONFIG_8139TOO_TUNE_TWISTER is not set
> # CONFIG_8139TOO_8129 is not set
> # CONFIG_SIS900 is not set
> # CONFIG_EPIC100 is not set
> # CONFIG_SUNDANCE is not set
> # CONFIG_TLAN is not set
> # CONFIG_VIA_RHINE is not set
> # CONFIG_WINBOND_840 is not set
> # CONFIG_HAPPYMEAL is not set
> # CONFIG_NET_POCKET is not set
>
> #
> # Ethernet (1000 Mbit)
> #
> # CONFIG_ACENIC is not set
> # CONFIG_HAMACHI is not set
> # CONFIG_YELLOWFIN is not set
> # CONFIG_SK98LIN is not set
> # CONFIG_FDDI is not set
> # CONFIG_HIPPI is not set
> # CONFIG_PLIP is not set
> CONFIG_PPP=m
> # CONFIG_PPP_MULTILINK is not set
> # CONFIG_PPP_FILTER is not set
> # CONFIG_PPP_ASYNC is not set
> # CONFIG_PPP_SYNC_TTY is not set
> CONFIG_PPP_DEFLATE=m
> CONFIG_PPP_BSDCOMP=m
> # CONFIG_PPPOE is not set
> # CONFIG_SLIP is not set
>
> #
> # Wireless LAN (non-hamradio)
> #
> # CONFIG_NET_RADIO is not set
>
> #
> # Token Ring devices
> #
> # CONFIG_TR is not set
> # CONFIG_NET_FC is not set
> # CONFIG_RCPCI is not set
> # CONFIG_SHAPER is not set
>
> #
> # Wan interfaces
> #
> # CONFIG_WAN is not set
>
> #
> # Amateur Radio support
> #
> # CONFIG_HAMRADIO is not set
>
> #
> # IrDA (infrared) support
> #
> # CONFIG_IRDA is not set
>
> #
> # ISDN subsystem
> #
> # CONFIG_ISDN is not set
>
> #
> # Old CD-ROM drivers (not SCSI, not IDE)
> #
> # CONFIG_CD_NO_IDESCSI is not set
>
> #
> # Input core support
> #
> # CONFIG_INPUT is not set
>
> #
> # Character devices
> #
> CONFIG_VT=y
> CONFIG_VT_CONSOLE=y
> CONFIG_SERIAL=y
> # CONFIG_SERIAL_CONSOLE is not set
> # CONFIG_SERIAL_EXTENDED is not set
> # CONFIG_SERIAL_NONSTANDARD is not set
> # CONFIG_UNIX98_PTYS is not set
> CONFIG_PRINTER=m
> # CONFIG_LP_CONSOLE is not set
> # CONFIG_PPDEV is not set
>
> #
> # I2C support
> #
> # CONFIG_I2C is not set
>
> #
> # Mice
> #
> # CONFIG_BUSMOUSE is not set
> CONFIG_MOUSE=y
> CONFIG_PSMOUSE=y
> # CONFIG_82C710_MOUSE is not set
> # CONFIG_PC110_PAD is not set
>
> #
> # Joysticks
> #
> # CONFIG_JOYSTICK is not set
>
> #
> # Input core support is needed for joysticks
> #
> # CONFIG_QIC02_TAPE is not set
>
> #
> # Watchdog Cards
> #
> # CONFIG_WATCHDOG is not set
> # CONFIG_INTEL_RNG is not set
> # CONFIG_NVRAM is not set
> # CONFIG_RTC is not set
> # CONFIG_DTLK is not set
> # CONFIG_R3964 is not set
> # CONFIG_APPLICOM is not set
>
> #
> # Ftape, the floppy tape device driver
> #
> # CONFIG_FTAPE is not set
> CONFIG_AGP=y
> # CONFIG_AGP_INTEL is not set
> # CONFIG_AGP_I810 is not set
> # CONFIG_AGP_VIA is not set
> # CONFIG_AGP_AMD is not set
> # CONFIG_AGP_SIS is not set
> # CONFIG_AGP_ALI is not set
> CONFIG_DRM=y
> # CONFIG_DRM_TDFX is not set
> # CONFIG_DRM_GAMMA is not set
> # CONFIG_DRM_R128 is not set
> # CONFIG_DRM_RADEON is not set
> # CONFIG_DRM_I810 is not set
> CONFIG_DRM_MGA=m
>
> #
> # Multimedia devices
> #
> # CONFIG_VIDEO_DEV is not set
>
> #
> # File systems
> #
> # CONFIG_QUOTA is not set
> # CONFIG_AUTOFS_FS is not set
> # CONFIG_AUTOFS4_FS is not set
> # CONFIG_REISERFS_FS is not set
> # CONFIG_REISERFS_CHECK is not set
> # CONFIG_ADFS_FS is not set
> # CONFIG_ADFS_FS_RW is not set
> # CONFIG_AFFS_FS is not set
> # CONFIG_HFS_FS is not set
> # CONFIG_BFS_FS is not set
> CONFIG_FAT_FS=m
> CONFIG_MSDOS_FS=m
> # CONFIG_UMSDOS_FS is not set
> CONFIG_VFAT_FS=m
> # CONFIG_EFS_FS is not set
> # CONFIG_JFFS_FS is not set
> # CONFIG_CRAMFS is not set
> # CONFIG_TMPFS is not set
> # CONFIG_RAMFS is not set
> CONFIG_ISO9660_FS=m
> CONFIG_JOLIET=y
> # CONFIG_MINIX_FS is not set
> # CONFIG_VXFS_FS is not set
> # CONFIG_NTFS_FS is not set
> # CONFIG_NTFS_RW is not set
> # CONFIG_HPFS_FS is not set
> CONFIG_PROC_FS=y
> # CONFIG_DEVFS_FS is not set
> # CONFIG_DEVFS_MOUNT is not set
> # CONFIG_DEVFS_DEBUG is not set
> # CONFIG_DEVPTS_FS is not set
> # CONFIG_QNX4FS_FS is not set
> # CONFIG_QNX4FS_RW is not set
> # CONFIG_ROMFS_FS is not set
> CONFIG_EXT2_FS=y
> # CONFIG_SYSV_FS is not set
> # CONFIG_SYSV_FS_WRITE is not set
> # CONFIG_UDF_FS is not set
> # CONFIG_UDF_RW is not set
> # CONFIG_UFS_FS is not set
> # CONFIG_UFS_FS_WRITE is not set
>
> #
> # Network File Systems
> #
> # CONFIG_CODA_FS is not set
> # CONFIG_NFS_FS is not set
> # CONFIG_NFS_V3 is not set
> # CONFIG_ROOT_NFS is not set
> # CONFIG_NFSD is not set
> # CONFIG_NFSD_V3 is not set
> # CONFIG_SUNRPC is not set
> # CONFIG_LOCKD is not set
> # CONFIG_SMB_FS is not set
> # CONFIG_NCP_FS is not set
> # CONFIG_NCPFS_PACKET_SIGNING is not set
> # CONFIG_NCPFS_IOCTL_LOCKING is not set
> # CONFIG_NCPFS_STRONG is not set
> # CONFIG_NCPFS_NFS_NS is not set
> # CONFIG_NCPFS_OS2_NS is not set
> # CONFIG_NCPFS_SMALLDOS is not set
> # CONFIG_NCPFS_NLS is not set
> # CONFIG_NCPFS_EXTRAS is not set
>
> #
> # Partition Types
> #
> # CONFIG_PARTITION_ADVANCED is not set
> CONFIG_MSDOS_PARTITION=y
> # CONFIG_SMB_NLS is not set
> CONFIG_NLS=y
>
> #
> # Native Language Support
> #
> CONFIG_NLS_DEFAULT="iso8859-1"
> # CONFIG_NLS_CODEPAGE_437 is not set
> # CONFIG_NLS_CODEPAGE_737 is not set
> # CONFIG_NLS_CODEPAGE_775 is not set
> # CONFIG_NLS_CODEPAGE_850 is not set
> # CONFIG_NLS_CODEPAGE_852 is not set
> # CONFIG_NLS_CODEPAGE_855 is not set
> # CONFIG_NLS_CODEPAGE_857 is not set
> # CONFIG_NLS_CODEPAGE_860 is not set
> # CONFIG_NLS_CODEPAGE_861 is not set
> # CONFIG_NLS_CODEPAGE_862 is not set
> # CONFIG_NLS_CODEPAGE_863 is not set
> # CONFIG_NLS_CODEPAGE_864 is not set
> # CONFIG_NLS_CODEPAGE_865 is not set
> # CONFIG_NLS_CODEPAGE_866 is not set
> # CONFIG_NLS_CODEPAGE_869 is not set
> # CONFIG_NLS_CODEPAGE_936 is not set
> # CONFIG_NLS_CODEPAGE_950 is not set
> # CONFIG_NLS_CODEPAGE_932 is not set
> # CONFIG_NLS_CODEPAGE_949 is not set
> # CONFIG_NLS_CODEPAGE_874 is not set
> # CONFIG_NLS_ISO8859_8 is not set
> # CONFIG_NLS_CODEPAGE_1251 is not set
> # CONFIG_NLS_ISO8859_1 is not set
> # CONFIG_NLS_ISO8859_2 is not set
> # CONFIG_NLS_ISO8859_3 is not set
> # CONFIG_NLS_ISO8859_4 is not set
> # CONFIG_NLS_ISO8859_5 is not set
> # CONFIG_NLS_ISO8859_6 is not set
> # CONFIG_NLS_ISO8859_7 is not set
> # CONFIG_NLS_ISO8859_9 is not set
> # CONFIG_NLS_ISO8859_13 is not set
> # CONFIG_NLS_ISO8859_14 is not set
> # CONFIG_NLS_ISO8859_15 is not set
> # CONFIG_NLS_KOI8_R is not set
> # CONFIG_NLS_KOI8_U is not set
> # CONFIG_NLS_UTF8 is not set
>
> #
> # Console drivers
> #
> CONFIG_VGA_CONSOLE=y
> CONFIG_VIDEO_SELECT=y
> # CONFIG_MDA_CONSOLE is not set
>
> #
> # Frame-buffer support
> #
> CONFIG_FB=y
> CONFIG_DUMMY_CONSOLE=y
> # CONFIG_FB_RIVA is not set
> # CONFIG_FB_CLGEN is not set
> # CONFIG_FB_PM2 is not set
> # CONFIG_FB_CYBER2000 is not set
> # CONFIG_FB_VESA is not set
> # CONFIG_FB_VGA16 is not set
> # CONFIG_FB_HGA is not set
> CONFIG_VIDEO_SELECT=y
> # CONFIG_FB_E1355 is not set
> CONFIG_FB_MATROX=m
> # CONFIG_FB_MATROX_MILLENIUM is not set
> # CONFIG_FB_MATROX_MYSTIQUE is not set
> CONFIG_FB_MATROX_G100=y
> # CONFIG_FB_MATROX_G450 is not set
> # CONFIG_FB_MATROX_MULTIHEAD is not set
> # CONFIG_FB_ATY is not set
> # CONFIG_FB_ATY128 is not set
> # CONFIG_FB_3DFX is not set
> # CONFIG_FB_SIS is not set
> # CONFIG_FB_VIRTUAL is not set
> CONFIG_FBCON_ADVANCED=y
> # CONFIG_FBCON_MFB is not set
> # CONFIG_FBCON_CFB2 is not set
> # CONFIG_FBCON_CFB4 is not set
> CONFIG_FBCON_CFB8=m
> CONFIG_FBCON_CFB16=m
> CONFIG_FBCON_CFB24=m
> CONFIG_FBCON_CFB32=m
> # CONFIG_FBCON_AFB is not set
> # CONFIG_FBCON_ILBM is not set
> # CONFIG_FBCON_IPLAN2P2 is not set
> # CONFIG_FBCON_IPLAN2P4 is not set
> # CONFIG_FBCON_IPLAN2P8 is not set
> # CONFIG_FBCON_MAC is not set
> # CONFIG_FBCON_VGA_PLANES is not set
> # CONFIG_FBCON_VGA is not set
> # CONFIG_FBCON_HGA is not set
> # CONFIG_FBCON_FONTWIDTH8_ONLY is not set
> # CONFIG_FBCON_FONTS is not set
> CONFIG_FONT_8x8=y
> CONFIG_FONT_8x16=y
>
> #
> # Sound
> #
> CONFIG_SOUND=y
> # CONFIG_SOUND_CMPCI is not set
> # CONFIG_SOUND_EMU10K1 is not set
> # CONFIG_SOUND_FUSION is not set
> # CONFIG_SOUND_CS4281 is not set
> CONFIG_SOUND_ES1370=m
> # CONFIG_SOUND_ES1371 is not set
> # CONFIG_SOUND_ESSSOLO1 is not set
> # CONFIG_SOUND_MAESTRO is not set
> # CONFIG_SOUND_MAESTRO3 is not set
> # CONFIG_SOUND_ICH is not set
> # CONFIG_SOUND_SONICVIBES is not set
> # CONFIG_SOUND_TRIDENT is not set
> # CONFIG_SOUND_MSNDCLAS is not set
> # CONFIG_SOUND_MSNDPIN is not set
> # CONFIG_SOUND_VIA82CXXX is not set
> # CONFIG_SOUND_OSS is not set
> # CONFIG_SOUND_TVMIXER is not set
>
> #
> # USB support
> #
> CONFIG_USB=m
> # CONFIG_USB_DEBUG is not set
>
> #
> # Miscellaneous USB options
> #
> # CONFIG_USB_DEVICEFS is not set
> # CONFIG_USB_BANDWIDTH is not set
>
> #
> # USB Controllers
> #
> # CONFIG_USB_UHCI is not set
> CONFIG_USB_UHCI_ALT=m
> # CONFIG_USB_OHCI is not set
>
> #
> # USB Device Class drivers
> #
> # CONFIG_USB_AUDIO is not set
> # CONFIG_USB_BLUETOOTH is not set
> CONFIG_USB_STORAGE=m
> # CONFIG_USB_STORAGE_DEBUG is not set
> # CONFIG_USB_STORAGE_FREECOM is not set
> # CONFIG_USB_STORAGE_DPCM is not set
> # CONFIG_USB_ACM is not set
> # CONFIG_USB_PRINTER is not set
>
> #
> # USB Human Interface Devices (HID)
> #
>
> #
> # Input core support is needed for USB HID
> #
>
> #
> # USB Imaging devices
> #
> # CONFIG_USB_DC2XX is not set
> # CONFIG_USB_MDC800 is not set
> # CONFIG_USB_SCANNER is not set
> # CONFIG_USB_MICROTEK is not set
>
> #
> # USB Multimedia devices
> #
> # CONFIG_USB_IBMCAM is not set
> # CONFIG_USB_OV511 is not set
> # CONFIG_USB_PWC is not set
> # CONFIG_USB_DSBR is not set
> # CONFIG_USB_DABUSB is not set
>
> #
> # USB Network adaptors
> #
> # CONFIG_USB_PLUSB is not set
> # CONFIG_USB_PEGASUS is not set
> # CONFIG_USB_NET1080 is not set
>
> #
> # USB port drivers
> #
> # CONFIG_USB_USS720 is not set
>
> #
> # USB Serial Converter support
> #
> # CONFIG_USB_SERIAL is not set
>
> #
> # USB misc drivers
> #
> # CONFIG_USB_RIO500 is not set
>
> #
> # Kernel hacking
> #
> # CONFIG_MAGIC_SYSRQ is not set
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/