>
> I've compiled 2.4.3mdk-25 source with Athlon optimizations, and the
> problem still happens.
>
> eth0 Link encap:Ethernet HWaddr FF:FF:FF:FF:FF:FF
> inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:4294967221 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:100
> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
> Interrupt:11 Base address:0x9000
>
> Look at the HWaddr. With default kernel (not compiled), I haven't this
> problem and my ethernet card goes well and the HWaddr is: ·"HWaddr
> 00:E0:29:9A:CB:62 ". And I'm sure after reboot I *MUST* restore all the
> values of my BIOS setup. Believe me, I know. :(
>
>
> Here is the output of dmesg when loading the 81389too module:
>
> Assertion failed! ioaddr != NULL,8139too.c,rtl8139_init_one,line=927
> eth0: SMC1211TX EZCard 10/100 (RealTek RTL8139) at 0x9000,
> ff:ff:ff:ff:ff:ff, IRQ 11
> eth0: Identified 8139 chip type 'RTL-8139C'
> eth0: Setting 100mbps half-duplex based on auto-negotiated partner
> ability
> ffff.
>
> "Assertion failed! ioaddr != NULL,8139too.c,rtl8139_init_one,line=927"?
> What is this? Is this the cause of the bug?
>
> Now the lspci -vv:
>
> 00:0c.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX
> (rev 10)
> Subsystem: Accton Technology Corporation EN-1207D Fast Ethernet Adapter
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 32 (8000ns min, 16000ns max)
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at 9000 [size=256]
> Region 1: Memory at da800000 (32-bit, non-prefetchable) [size=256]
> Expansion ROM at <unassigned> [disabled] [size=64K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> I hope these lines can help.
ADDON:
Dmesg:
[...
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is ffffffff. (queue head)
eth0: Tx descriptor 1 is ffffffff.
eth0: Tx descriptor 2 is ffffffff.
eth0: Tx descriptor 3 is ffffffff.
eth0: Setting 100mbps half-duplex based on auto-negotiated partner ability
ffff.
probable hardware bug: clock timer configuration lost - probably a VIA686a
motherboard.
probable hardware bug: restoring chip configuration.
...]
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/