I'm getting many replies to my "Persistent 2.4.x stability problem"
post. Manfred Spraul has been extremely helpful in working through the
issue with me and providing the "noapic" work-around, but this problem
is fairly subtle and is most likely effecting a lot more people than
those reporting the issue.
It seems like some Tyan motherboards and _all_ HP hardware do not play
well with the APIC code. That's a pretty big subset of hardware; Asus
also seems to be effected now, and many other platforms may also suffer
from APICitis. I realize there are different failure modes and I assume
different issues are involved within the APIC code.
I have HP hardware that I can make available for patches and tests -- I
want to help solve this and contribute what I can. Using "noapic" does
take the pressure off the issue, but I guess this problem remains
insidious in my mind. I realize I'm not fully familiar with the general
issues, so I apologize if I'm re-covering old ground or missing any
relevant issues.
Thanks,
-- Ken.On Thursday, May 3, 2001, at 10:51 AM, David A. Neal wrote:
> I am encountering a problem I am having a little difficulty > trying to solve. I have a system with a ASUS CUV4X-DLS system > board, Bios 1004, 1GB of memory. dual P3 933MHz processors, > a G450 Matrox card in the AGP slot, and a SBLive! sound > card in PCI Slot 4. > > I have provided the output from dmesg below and the .config > file I used in compiling the 2.4.4 kernel on this system > with a Redhat 7.1 (Seawolf) distribution. > > The problem is that the system will boot everytime if and only > if I use "noapic". If I do not use "noapic", the system will > boot sometimes. The dmesg info below is from a successful boot > when I did not use "noapic". When I do not use "noapic" > __and__ it does not boot, the boot sequence stops at > > ..TIMER: vector=49 pin1=2 pin2=0 > > Matter of fact, the first boot after installing Redhat 7.1 stop > at the same message/location with the 2.4.2 kernel. > > I thought about "append"(ing) some "pirq" arguments to the boot > but I really not sure how to do this and whether or not it > would fix the problem. > > What is the impact on performance by disabling APIC? Is there > something wrong with the .config file that might fix this. > > > =================== Begin dmesg > info ====================================== > Linux version 2.4.4 (root@ouzel) (gcc version 2.96 20000731 (Red Hat > Linux 7.1 2.96-81)) #2 SMP Wed May 2 17:19:43 MDT 2001 > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009f000 (usable) > BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 000000003fffc000 (usable) > BIOS-e820: 000000003fffc000 - 000000003ffff000 (ACPI data) > BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS) > BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) > 127MB HIGHMEM available. > Scan SMP from c0000000 for 1024 bytes. > Scan SMP from c009fc00 for 1024 bytes. > Scan SMP from c00f0000 for 65536 bytes. > found SMP MP-table at 000f54c0 > hm, page 000f5000 reserved twice. > hm, page 000f6000 reserved twice. > hm, page 000f5000 reserved twice. > hm, page 000f6000 reserved twice. > On node 0 totalpages: 262140 > zone(0): 4096 pages. > zone(1): 225280 pages. > zone(2): 32764 pages. > Intel MultiProcessor Specification v1.4 > Virtual Wire compatibility mode. > OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000 > Processor #3 Pentium(tm) Pro APIC version 17 > Floating point unit present. > Machine Exception supported. > 64 bit compare & exchange supported. > Internal APIC present. > SEP present. > MTRR present. > PGE present. > MCA present. > CMOV present. > PAT present. > PSE present. > MMX present. > FXSR present. > XMM present. > Bootup CPU > Processor #0 Pentium(tm) Pro APIC version 17 > Floating point unit present. > Machine Exception supported. > 64 bit compare & exchange supported. > Internal APIC present. > SEP present. > MTRR present. > PGE present. > MCA present. > CMOV present. > PAT present. > PSE present. > MMX present. > FXSR present. > XMM present. > Bus #0 is PCI > Bus #1 is PCI > Bus #2 is ISA > I/O APIC #2 Version 17 at 0xFEC00000. > Int: type 3, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 00 > Int: type 0, pol 0, trig 0, bus 2, IRQ 01, APIC ID 2, APIC INT 01 > Int: type 0, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 02 > Int: type 0, pol 0, trig 0, bus 2, IRQ 03, APIC ID 2, APIC INT 03 > Int: type 0, pol 0, trig 0, bus 2, IRQ 04, APIC ID 2, APIC INT 04 > Int: type 0, pol 0, trig 0, bus 2, IRQ 06, APIC ID 2, APIC INT 06 > Int: type 0, pol 0, trig 0, bus 2, IRQ 07, APIC ID 2, APIC INT 07 > Int: type 0, pol 0, trig 0, bus 2, IRQ 08, APIC ID 2, APIC INT 08 > Int: type 0, pol 0, trig 0, bus 2, IRQ 0c, APIC ID 2, APIC INT 0c > Int: type 0, pol 0, trig 0, bus 2, IRQ 0e, APIC ID 2, APIC INT 0e > Int: type 0, pol 0, trig 0, bus 2, IRQ 0f, APIC ID 2, APIC INT 0f > Int: type 0, pol 3, trig 3, bus 1, IRQ 00, APIC ID 2, APIC INT 10 > Int: type 0, pol 3, trig 3, bus 2, IRQ 00, APIC ID 2, APIC INT 00 > Int: type 0, pol 3, trig 3, bus 0, IRQ 13, APIC ID 2, APIC INT 12 > Int: type 0, pol 3, trig 3, bus 0, IRQ 1c, APIC ID 2, APIC INT 11 > Int: type 0, pol 3, trig 3, bus 0, IRQ 20, APIC ID 2, APIC INT 13 > Int: type 0, pol 3, trig 3, bus 0, IRQ 21, APIC ID 2, APIC INT 10 > Int: type 0, pol 3, trig 3, bus 0, IRQ 28, APIC ID 2, APIC INT 12 > Lint: type 3, pol 1, trig 1, bus 2, IRQ 00, APIC ID ff, APIC LINT 00 > Lint: type 1, pol 1, trig 1, bus 2, IRQ 00, APIC ID ff, APIC LINT 01 > Processors: 2 > mapped APIC to ffffe000 (fee00000) > mapped IOAPIC to ffffd000 (fec00000) > Kernel command line: auto BOOT_IMAGE=linux ro root=801 > BOOT_FILE=/boot/vmlinuz-2.4.4 > Initializing CPU#0 > Detected 937.577 MHz processor. > Console: colour VGA+ 80x25 > Calibrating delay loop... 1867.77 BogoMIPS > Memory: 1028188k/1048560k available (1353k kernel code, 19984k > reserved, 560k data, 228k init, 131056k highmem) > Dentry-cache hash table entries: 131072 (order: 8, 1048576 bytes) > Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes) > Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) > Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) > CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0 > CPU: L1 I cache: 16K, L1 D cache: 16K > CPU: L2 cache: 256K > Intel machine check architecture supported. > Intel machine check reporting enabled on CPU#0. > CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000 > CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 > CPU: Common caps: 0383fbff 00000000 00000000 00000000 > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Checking 'hlt' instruction... OK. > POSIX conformance testing by UNIFIX > CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0 > CPU: L1 I cache: 16K, L1 D cache: 16K > CPU: L2 cache: 256K > Intel machine check reporting enabled on CPU#0. > CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000 > CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 > CPU: Common caps: 0383fbff 00000000 00000000 00000000 > CPU0: Intel Pentium III (Coppermine) stepping 06 > per-CPU timeslice cutoff: 731.39 usecs. > Getting VERSION: 40011 > Getting VERSION: 40011 > Getting ID: 3000000 > Getting ID: c000000 > Getting LVT0: 8700 > Getting LVT1: 400 > enabled ExtINT on CPU#0 > ESR value before enabling vector: 00000000 > ESR value after enabling vector: 00000000 > CPU present map: 9 > Booting processor 1/0 eip 2000 > Setting warm reset code and vector. > 1. > 2. > 3. > Asserting INIT. > Waiting for send to finish... > +Deasserting INIT. > Waiting for send to finish... > +#startup loops: 2. > Sending STARTUP #1. > After apic_write. > Initializing CPU#1 > CPU#1 (phys ID: 0) waiting for CALLOUT > Startup point 1. > Waiting for send to finish... > +Sending STARTUP #2. > After apic_write. > Startup point 1. > Waiting for send to finish... > +After Startup. > Before Callout 1. > After Callout 1. > CALLIN, before setup_local_APIC(). > masked ExtINT on CPU#1 > ESR value before enabling vector: 00000000 > ESR value after enabling vector: 00000000 > Calibrating delay loop... 1874.32 BogoMIPS > Stack at about c211dfb8 > CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0 > CPU: L1 I cache: 16K, L1 D cache: 16K > CPU: L2 cache: 256K > Intel machine check reporting enabled on CPU#1. > CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000 > CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 > CPU: Common caps: 0383fbff 00000000 00000000 00000000 > OK. > CPU1: Intel Pentium III (Coppermine) stepping 06 > CPU has booted. > Before bogomips. > Total of 2 processors activated (3742.10 BogoMIPS). > Before bogocount - setting activated=1. > Boot done. > ENABLING IO-APIC IRQs > ...changing IO-APIC physical APIC ID to 2 ... ok. > Synchronizing Arb IDs. > init IO_APIC IRQs > IO-APIC (apicid-pin) 2-5, 2-9, 2-10, 2-11, 2-13, 2-20, 2-21, 2-22, > 2-23 not connected. > ..TIMER: vector=49 pin1=2 pin2=0 > number of MP IRQ sources: 18. > number of IO-APIC #2 registers: 24. > testing the IO APIC....................... > > IO APIC #2...... > .... register #00: 02000000 > ....... : physical APIC id: 02 > .... register #01: 00178011 > ....... : max redirection entries: 0017 > ....... : IO APIC version: 0011 > WARNING: unexpected IO-APIC, please mail > to linux-smp@vger.kernel.org > .... register #02: 00000000 > ....... : arbitration: 00 > .... IRQ redirection table: > NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: > 00 003 03 0 1 1 1 1 1 1 31 > 01 003 03 0 0 0 0 0 1 1 39 > 02 003 03 0 0 0 0 0 1 1 31 > 03 003 03 0 0 0 0 0 1 1 41 > 04 003 03 0 0 0 0 0 1 1 49 > 05 000 00 1 0 0 0 0 0 0 00 > 06 003 03 0 0 0 0 0 1 1 51 > 07 003 03 0 0 0 0 0 1 1 59 > 08 003 03 0 0 0 0 0 1 1 61 > 09 000 00 1 0 0 0 0 0 0 00 > 0a 000 00 1 0 0 0 0 0 0 00 > 0b 000 00 1 0 0 0 0 0 0 00 > 0c 003 03 0 0 0 0 0 1 1 69 > 0d 000 00 1 0 0 0 0 0 0 00 > 0e 003 03 0 0 0 0 0 1 1 71 > 0f 003 03 0 0 0 0 0 1 1 79 > 10 003 03 1 1 0 1 0 1 1 81 > 11 003 03 1 1 0 1 0 1 1 89 > 12 003 03 1 1 0 1 0 1 1 91 > 13 003 03 1 1 0 1 0 1 1 99 > 14 000 00 1 0 0 0 0 0 0 00 > 15 000 00 1 0 0 0 0 0 0 00 > 16 000 00 1 0 0 0 0 0 0 00 > 17 000 00 1 0 0 0 0 0 0 00 > IRQ to pin mappings: > IRQ0 -> 0-> 2 > IRQ1 -> 1 > IRQ3 -> 3 > IRQ4 -> 4 > IRQ6 -> 6 > IRQ7 -> 7 > IRQ8 -> 8 > IRQ12 -> 12 > IRQ14 -> 14 > IRQ15 -> 15 > IRQ16 -> 16 > IRQ17 -> 17 > IRQ18 -> 18 > IRQ19 -> 19 > .................................... done. > calibrating APIC timer ... > ..... CPU clock speed is 937.6805 MHz. > ..... host bus clock speed is 133.9542 MHz. > cpu: 0, clocks: 1339542, slice: 446514 > CPU0<T0:1339536,T1:893008,D:14,S:446514,C:1339542> > cpu: 1, clocks: 1339542, slice: 446514 > CPU1<T0:1339536,T1:445552,D:956,S:446514,C:1339542> > checking TSC synchronization across CPUs: passed. > Setting commenced=1, go go go > PCI: PCI BIOS revision 2.10 entry at 0xf0d00, last bus=1 > PCI: Using configuration type 1 > PCI: Probing PCI hardware > PCI: Disabled enhanced CPU to PCI posting > PCI: Disabled enhanced CPU to PCI posting #2 > Unknown bridge resource 0: assuming transparent > PCI: Using IRQ router VIA [1106/0686] at 00:04.0 > PCI->APIC IRQ transform: (B0,I4,P3) -> 18 > PCI->APIC IRQ transform: (B0,I4,P3) -> 18 > PCI->APIC IRQ transform: (B0,I7,P0) -> 17 > PCI->APIC IRQ transform: (B0,I8,P0) -> 19 > PCI->APIC IRQ transform: (B0,I8,P1) -> 16 > PCI->APIC IRQ transform: (B0,I10,P0) -> 18 > PCI->APIC IRQ transform: (B1,I0,P0) -> 16 > Linux NET4.0 for Linux 2.4 > Based upon Swansea University Computer Society NET3.039 > Starting kswapd v1.8 > i2c-core.o: i2c core module > i2c-dev.o: i2c /dev entries driver module > i2c-core.o: driver i2c-dev dummy driver registered. > pty: 256 Unix98 ptys configured > block: queued sectors max/low 683440kB/552368kB, 2048 slots per queue > RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize > Uniform Multi-Platform E-IDE driver Revision: 6.31 > ide: Assuming 33MHz system bus speed for PIO modes; override with > idebus=xx > VP_IDE: IDE controller on PCI bus 00 dev 21 > VP_IDE: chipset revision 6 > VP_IDE: not 100% native mode: will probe irqs later > hda: RICOH CD-R/RW MP7120A, ATAPI CD/DVD-ROM drive > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > hda: ATAPI 32X CD-ROM CD-R/RW drive, 4096kB Cache > Uniform CD-ROM driver Revision: 3.12 > Floppy drive(s): fd0 is 1.44M > FDC 0 is a post-1991 82077 > Loading I2O Core - (c) Copyright 1999 Red Hat Software > Linux I2O PCI support (c) 1999 Red Hat Software. > i2o: Checking for PCI I2O controllers... > I2O configuration manager v 0.04. > (C) Copyright 1999 Red Hat Software > I2O Block Storage OSM v0.9 > (c) Copyright 1999, 2000 Red Hat Software. > I2O LAN OSM (C) 1999 University of Helsinki. > loop: loaded (max 8 devices) > Serial driver version 5.05a (2001-03-20) with MANY_PORTS SHARE_IRQ > SERIAL_PCI enabled > ttyS00 at 0x03f8 (irq = 4) is a 16550A > ttyS01 at 0x02f8 (irq = 3) is a 16550A > Real Time Clock Driver v1.10d > eepro100.c:v1.09j-t 9/29/99 Donald Becker > http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html > eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. > Savochkin <saw@saw.sw.com.sg> and others > eth0: Intel Corporation 82557 [Ethernet Pro 100], 00:E0:18:06:E3:F7, > IRQ 17. > Board assembly 733470-006, Physical connectors present: RJ45 > Primary interface chip i82555 PHY #1. > General self-test: passed. > Serial sub-system self-test: passed. > Internal registers self-test: passed. > ROM checksum self-test: passed (0x04f4518b). > Linux agpgart interface v0.99 (c) Jeff Hartmann > agpgart: Maximum main memory to use for agp memory: 816M > agpgart: Detected Via Apollo Pro chipset > agpgart: AGP aperture is 32M @ 0xfc000000 > [drm] AGP 0.99 on VIA Apollo Pro @ 0xfc000000 32MB > [drm] Initialized tdfx 1.0.0 20000928 on minor 63 > [drm] AGP 0.99 on VIA Apollo Pro @ 0xfc000000 32MB > [drm] Initialized radeon 1.0.0 20010105 on minor 62 > SCSI subsystem driver Revision: 1.00 > sym53c8xx: at PCI bus 0, device 8, function 0 > sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up) > sym53c8xx: 53c1010-33 detected with Symbios NVRAM > sym53c8xx: at PCI bus 0, device 8, function 1 > sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up) > sym53c8xx: 53c1010-33 detected with Symbios NVRAM > sym53c1010-33-0: rev 0x1 on pci bus 0 device 8 function 0 irq 19 > sym53c1010-33-0: Symbios format NVRAM, ID 7, Fast-80, Parity Checking > sym53c1010-33-0: on-chip RAM at 0xf6800000 > sym53c1010-33-0: restart (scsi reset). > sym53c1010-33-0: handling phase mismatch from SCRIPTS. > sym53c1010-33-0: Downloading SCSI SCRIPTS. > sym53c1010-33-1: rev 0x1 on pci bus 0 device 8 function 1 irq 16 > sym53c1010-33-1: Symbios format NVRAM, ID 7, Fast-80, Parity Checking > sym53c1010-33-1: on-chip RAM at 0xf5800000 > sym53c1010-33-1: restart (scsi reset). > sym53c1010-33-1: handling phase mismatch from SCRIPTS. > sym53c1010-33-1: Downloading SCSI SCRIPTS. > scsi0 : sym53c8xx-1.7.3a-20010304 > scsi1 : sym53c8xx-1.7.3a-20010304 > Vendor: WDIGTL Model: WDE18310 ULTRA3 Rev: 1.30 > Type: Direct-Access ANSI SCSI revision: 03 > sym53c1010-33-0-<0,0>: tagged command queue depth set to 4 > Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 > sym53c1010-33-0-<0,*>: FAST-80 WIDE SCSI 160.0 MB/s (12.5 ns, offset 62) > SCSI device sda: 35761710 512-byte hdwr sectors (18310 MB) > Partition check: > sda: sda1 sda2 sda3 sda4 > Creative EMU10K1 PCI Audio Driver, version 0.7, 16:51:09 May 2 2001 > emu10k1: EMU10K1 rev 8 model 0x8027 found, IO at 0xa800-0xa81f, IRQ 18 > usb.c: registered new driver hub > uhci.c: USB UHCI at I/O 0xd400, IRQ 18 > usb.c: new USB bus registered, assigned bus number 1 > hub.c: USB hub found > hub.c: 2 ports detected > uhci.c: USB UHCI at I/O 0xd000, IRQ 18 > usb.c: new USB bus registered, assigned bus number 2 > hub.c: USB hub found > hub.c: 2 ports detected > Initializing USB Mass Storage driver... > usb.c: registered new driver usb-storage > USB Mass Storage support registered. > i2o_scsi.c: Version 0.0.1 > chain_pool: 0 bytes @ f7cc5e00 > (512 byte buffers X 4 can_queue X 0 i2o controllers) > NET4: Linux TCP/IP 1.0 for NET4.0 > IP Protocols: ICMP, UDP, TCP, IGMP > IP: routing cache hash table of 8192 buckets, 64Kbytes > TCP: Hash tables configured (established 262144 bind 65536) > NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. > VFS: Mounted root (ext2 filesystem) readonly. > Freeing unused kernel memory: 228k freed > Adding Swap: 2097136k swap-space (priority -1) > > > ==================== Begin .config ============================ > # > # Automatically generated make config: don't edit > # > CONFIG_X86=y > CONFIG_ISA=y > # CONFIG_SBUS is not set > CONFIG_UID16=y > > # > # Code maturity level options > # > CONFIG_EXPERIMENTAL=y > > # > # Loadable module support > # > CONFIG_MODULES=y > CONFIG_MODVERSIONS=y > CONFIG_KMOD=y > > # > # Processor type and features > # > # CONFIG_M386 is not set > # CONFIG_M486 is not set > # CONFIG_M586 is not set > # CONFIG_M586TSC is not set > # CONFIG_M586MMX is not set > # CONFIG_M686 is not set > CONFIG_MPENTIUMIII=y > # CONFIG_MPENTIUM4 is not set > # CONFIG_MK6 is not set > # CONFIG_MK7 is not set > # CONFIG_MCRUSOE is not set > # CONFIG_MWINCHIPC6 is not set > # CONFIG_MWINCHIP2 is not set > # CONFIG_MWINCHIP3D is not set > # CONFIG_MCYRIXIII is not set > CONFIG_X86_WP_WORKS_OK=y > CONFIG_X86_INVLPG=y > CONFIG_X86_CMPXCHG=y > CONFIG_X86_XADD=y > CONFIG_X86_BSWAP=y > CONFIG_X86_POPAD_OK=y > # CONFIG_RWSEM_GENERIC_SPINLOCK is not set > CONFIG_RWSEM_XCHGADD_ALGORITHM=y > CONFIG_X86_L1_CACHE_SHIFT=5 > CONFIG_X86_TSC=y > CONFIG_X86_GOOD_APIC=y > CONFIG_X86_PGE=y > CONFIG_X86_USE_PPRO_CHECKSUM=y > # CONFIG_TOSHIBA is not set > # CONFIG_MICROCODE is not set > # CONFIG_X86_MSR is not set > # CONFIG_X86_CPUID is not set > # CONFIG_NOHIGHMEM is not set > CONFIG_HIGHMEM4G=y > # CONFIG_HIGHMEM64G is not set > CONFIG_HIGHMEM=y > # CONFIG_MATH_EMULATION is not set > # CONFIG_MTRR is not set > CONFIG_SMP=y > CONFIG_HAVE_DEC_LOCK=y > > # > # General setup > # > CONFIG_NET=y > # CONFIG_VISWS is not set > CONFIG_X86_IO_APIC=y > CONFIG_X86_LOCAL_APIC=y > CONFIG_PCI=y > # CONFIG_PCI_GOBIOS is not set > # CONFIG_PCI_GODIRECT is not set > CONFIG_PCI_GOANY=y > CONFIG_PCI_BIOS=y > CONFIG_PCI_DIRECT=y > CONFIG_PCI_NAMES=y > # CONFIG_EISA is not set > # CONFIG_MCA is not set > # CONFIG_HOTPLUG is not set > # CONFIG_PCMCIA is not set > CONFIG_SYSVIPC=y > CONFIG_BSD_PROCESS_ACCT=y > CONFIG_SYSCTL=y > CONFIG_KCORE_ELF=y > # CONFIG_KCORE_AOUT is not set > CONFIG_BINFMT_AOUT=y > CONFIG_BINFMT_ELF=y > CONFIG_BINFMT_MISC=y > # CONFIG_PM is not set > # CONFIG_ACPI is not set > # CONFIG_APM is not set > > # > # Memory Technology Devices (MTD) > # > # CONFIG_MTD is not set > > # > # Parallel port support > # > # CONFIG_PARPORT is not set > > # > # Plug and Play configuration > # > # CONFIG_PNP is not set > # CONFIG_ISAPNP is not set > > # > # Block devices > # > CONFIG_BLK_DEV_FD=y > # CONFIG_BLK_DEV_XD is not set > # CONFIG_PARIDE is not set > # CONFIG_BLK_CPQ_DA is not set > # CONFIG_BLK_CPQ_CISS_DA is not set > # CONFIG_BLK_DEV_DAC960 is not set > CONFIG_BLK_DEV_LOOP=y > # CONFIG_BLK_DEV_NBD is not set > CONFIG_BLK_DEV_RAM=y > CONFIG_BLK_DEV_RAM_SIZE=4096 > CONFIG_BLK_DEV_INITRD=y > > # > # Multi-device support (RAID and LVM) > # > # CONFIG_MD is not set > # CONFIG_BLK_DEV_MD is not set > # CONFIG_MD_LINEAR is not set > # CONFIG_MD_RAID0 is not set > # CONFIG_MD_RAID1 is not set > # CONFIG_MD_RAID5 is not set > # CONFIG_BLK_DEV_LVM is not set > > # > # Networking options > # > CONFIG_PACKET=y > # CONFIG_PACKET_MMAP is not set > # CONFIG_NETLINK is not set > # CONFIG_NETFILTER is not set > # CONFIG_FILTER is not set > CONFIG_UNIX=y > CONFIG_INET=y > CONFIG_IP_MULTICAST=y > # CONFIG_IP_ADVANCED_ROUTER is not set > # CONFIG_IP_PNP is not set > # CONFIG_NET_IPIP is not set > # CONFIG_NET_IPGRE is not set > # CONFIG_IP_MROUTE is not set > # CONFIG_INET_ECN is not set > CONFIG_SYN_COOKIES=y > # CONFIG_IPV6 is not set > # CONFIG_KHTTPD is not set > # CONFIG_ATM is not set > > # > # > # > # CONFIG_IPX is not set > # CONFIG_ATALK is not set > # CONFIG_DECNET is not set > # CONFIG_BRIDGE is not set > # CONFIG_X25 is not set > # CONFIG_LAPB is not set > # CONFIG_LLC is not set > # CONFIG_NET_DIVERT is not set > # CONFIG_ECONET is not set > # CONFIG_WAN_ROUTER is not set > # CONFIG_NET_FASTROUTE is not set > # CONFIG_NET_HW_FLOWCONTROL is not set > > # > # QoS and/or fair queueing > # > # CONFIG_NET_SCHED is not set > > # > # Telephony Support > # > # CONFIG_PHONE is not set > # CONFIG_PHONE_IXJ is not set > > # > # ATA/IDE/MFM/RLL support > # > CONFIG_IDE=y > > # > # IDE, ATA and ATAPI Block devices > # > CONFIG_BLK_DEV_IDE=y > > # > # Please see Documentation/ide.txt for help/info on IDE drives > # > # CONFIG_BLK_DEV_HD_IDE is not set > # CONFIG_BLK_DEV_HD is not set > # CONFIG_BLK_DEV_IDEDISK is not set > # CONFIG_IDEDISK_MULTI_MODE is not set > # CONFIG_BLK_DEV_IDEDISK_VENDOR is not set > # CONFIG_BLK_DEV_IDEDISK_FUJITSU is not set > # CONFIG_BLK_DEV_IDEDISK_IBM is not set > # CONFIG_BLK_DEV_IDEDISK_MAXTOR is not set > # CONFIG_BLK_DEV_IDEDISK_QUANTUM is not set > # CONFIG_BLK_DEV_IDEDISK_SEAGATE is not set > # CONFIG_BLK_DEV_IDEDISK_WD is not set > # CONFIG_BLK_DEV_COMMERIAL is not set > # CONFIG_BLK_DEV_TIVO is not set > # CONFIG_BLK_DEV_IDECS is not set > CONFIG_BLK_DEV_IDECD=y > # CONFIG_BLK_DEV_IDETAPE is not set > # CONFIG_BLK_DEV_IDEFLOPPY is not set > # CONFIG_BLK_DEV_IDESCSI is not set > > # > # IDE chipset support/bugfixes > # > CONFIG_BLK_DEV_CMD640=y > # CONFIG_BLK_DEV_CMD640_ENHANCED is not set > # CONFIG_BLK_DEV_ISAPNP is not set > CONFIG_BLK_DEV_RZ1000=y > CONFIG_BLK_DEV_IDEPCI=y > CONFIG_IDEPCI_SHARE_IRQ=y > # CONFIG_BLK_DEV_IDEDMA_PCI is not set > # CONFIG_BLK_DEV_OFFBOARD is not set > # CONFIG_IDEDMA_PCI_AUTO is not set > # CONFIG_BLK_DEV_IDEDMA is not set > # CONFIG_IDEDMA_PCI_WIP is not set > # CONFIG_IDEDMA_NEW_DRIVE_LISTINGS is not set > # CONFIG_BLK_DEV_AEC62XX is not set > # CONFIG_AEC62XX_TUNING is not set > # CONFIG_BLK_DEV_ALI15X3 is not set > # CONFIG_WDC_ALI15X3 is not set > # CONFIG_BLK_DEV_AMD7409 is not set > # CONFIG_AMD7409_OVERRIDE is not set > # CONFIG_BLK_DEV_CMD64X is not set > # CONFIG_BLK_DEV_CY82C693 is not set > # CONFIG_BLK_DEV_CS5530 is not set > # CONFIG_BLK_DEV_HPT34X is not set > # CONFIG_HPT34X_AUTODMA is not set > # CONFIG_BLK_DEV_HPT366 is not set > # CONFIG_BLK_DEV_PIIX is not set > # CONFIG_PIIX_TUNING is not set > # CONFIG_BLK_DEV_NS87415 is not set > # CONFIG_BLK_DEV_OPTI621 is not set > # CONFIG_BLK_DEV_PDC202XX is not set > # CONFIG_PDC202XX_BURST is not set > # CONFIG_BLK_DEV_OSB4 is not set > # CONFIG_BLK_DEV_SIS5513 is not set > # CONFIG_BLK_DEV_SLC90E66 is not set > # CONFIG_BLK_DEV_TRM290 is not set > # CONFIG_BLK_DEV_VIA82CXXX is not set > # CONFIG_IDE_CHIPSETS is not set > # CONFIG_IDEDMA_AUTO is not set > # CONFIG_DMA_NONPCI is not set > CONFIG_BLK_DEV_IDE_MODES=y > > # > # SCSI support > # > CONFIG_SCSI=y > > # > # SCSI support type (disk, tape, CD-ROM) > # > CONFIG_BLK_DEV_SD=y > CONFIG_SD_EXTRA_DEVS=40 > # CONFIG_CHR_DEV_ST is not set > # CONFIG_CHR_DEV_OSST is not set > # CONFIG_BLK_DEV_SR is not set > # CONFIG_CHR_DEV_SG is not set > > # > # Some SCSI devices (e.g. CD jukebox) support multiple LUNs > # > CONFIG_SCSI_DEBUG_QUEUES=y > CONFIG_SCSI_MULTI_LUN=y > CONFIG_SCSI_CONSTANTS=y > # CONFIG_SCSI_LOGGING is not set > > # > # SCSI low-level drivers > # > # CONFIG_BLK_DEV_3W_XXXX_RAID is not set > # CONFIG_SCSI_7000FASST is not set > # CONFIG_SCSI_ACARD is not set > # CONFIG_SCSI_AHA152X is not set > # CONFIG_SCSI_AHA1542 is not set > # CONFIG_SCSI_AHA1740 is not set > # CONFIG_SCSI_AIC7XXX is not set > # CONFIG_SCSI_AIC7XXX_OLD is not set > # CONFIG_SCSI_ADVANSYS is not set > # CONFIG_SCSI_IN2000 is not set > # CONFIG_SCSI_AM53C974 is not set > # CONFIG_SCSI_MEGARAID is not set > # CONFIG_SCSI_BUSLOGIC is not set > # CONFIG_SCSI_CPQFCTS is not set > # CONFIG_SCSI_DMX3191D is not set > # CONFIG_SCSI_DTC3280 is not set > # CONFIG_SCSI_EATA is not set > # CONFIG_SCSI_EATA_DMA is not set > # CONFIG_SCSI_EATA_PIO is not set > # CONFIG_SCSI_FUTURE_DOMAIN is not set > # CONFIG_SCSI_GDTH is not set > # CONFIG_SCSI_GENERIC_NCR5380 is not set > # CONFIG_SCSI_IPS is not set > # CONFIG_SCSI_INITIO is not set > # CONFIG_SCSI_INIA100 is not set > # CONFIG_SCSI_NCR53C406A is not set > # CONFIG_SCSI_NCR53C7xx is not set > # CONFIG_SCSI_NCR53C8XX is not set > CONFIG_SCSI_SYM53C8XX=y > CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS=4 > CONFIG_SCSI_NCR53C8XX_MAX_TAGS=32 > CONFIG_SCSI_NCR53C8XX_SYNC=20 > # CONFIG_SCSI_NCR53C8XX_PROFILE is not set > # CONFIG_SCSI_NCR53C8XX_IOMAPPED is not set > # CONFIG_SCSI_NCR53C8XX_PQS_PDS is not set > # CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT is not set > # CONFIG_SCSI_PAS16 is not set > # CONFIG_SCSI_PCI2000 is not set > # CONFIG_SCSI_PCI2220I is not set > # CONFIG_SCSI_PSI240I is not set > # CONFIG_SCSI_QLOGIC_FAS is not set > # CONFIG_SCSI_QLOGIC_ISP is not set > # CONFIG_SCSI_QLOGIC_FC is not set > # CONFIG_SCSI_QLOGIC_1280 is not set > # CONFIG_SCSI_SEAGATE is not set > # CONFIG_SCSI_SIM710 is not set > # CONFIG_SCSI_SYM53C416 is not set > # CONFIG_SCSI_DC390T is not set > # CONFIG_SCSI_T128 is not set > # CONFIG_SCSI_U14_34F is not set > # CONFIG_SCSI_ULTRASTOR is not set > # CONFIG_SCSI_DEBUG is not set > > # > # IEEE 1394 (FireWire) support > # > # CONFIG_IEEE1394 is not set > > # > # I2O device support > # > CONFIG_I2O=y > CONFIG_I2O_PCI=y > CONFIG_I2O_BLOCK=y > CONFIG_I2O_LAN=y > CONFIG_I2O_SCSI=y > CONFIG_I2O_PROC=y > > # > # Network device support > # > CONFIG_NETDEVICES=y > > # > # ARCnet devices > # > # CONFIG_ARCNET is not set > # CONFIG_DUMMY is not set > # CONFIG_BONDING is not set > # CONFIG_EQUALIZER is not set > # CONFIG_TUN is not set > # CONFIG_NET_SB1000 is not set > > # > # Ethernet (10 or 100Mbit) > # > CONFIG_NET_ETHERNET=y > # CONFIG_NET_VENDOR_3COM is not set > # CONFIG_LANCE is not set > # CONFIG_NET_VENDOR_SMC is not set > # CONFIG_NET_VENDOR_RACAL is not set > # CONFIG_AT1700 is not set > # CONFIG_DEPCA is not set > # CONFIG_HP100 is not set > # CONFIG_NET_ISA is not set > CONFIG_NET_PCI=y > # CONFIG_PCNET32 is not set > # CONFIG_ADAPTEC_STARFIRE is not set > # CONFIG_AC3200 is not set > # CONFIG_APRICOT is not set > # CONFIG_CS89x0 is not set > # CONFIG_TULIP is not set > # CONFIG_DE4X5 is not set > # CONFIG_DGRS is not set > # CONFIG_DM9102 is not set > CONFIG_EEPRO100=y > # CONFIG_EEPRO100_PM is not set > # CONFIG_LNE390 is not set > # CONFIG_NATSEMI is not set > # CONFIG_NE2K_PCI is not set > # CONFIG_NE3210 is not set > # CONFIG_ES3210 is not set > # CONFIG_8139TOO is not set > # CONFIG_8139TOO_PIO is not set > # CONFIG_8139TOO_TUNE_TWISTER is not set > # CONFIG_8139TOO_8129 is not set > # CONFIG_SIS900 is not set > # CONFIG_EPIC100 is not set > # CONFIG_SUNDANCE is not set > # CONFIG_TLAN is not set > # CONFIG_VIA_RHINE is not set > # CONFIG_WINBOND_840 is not set > # CONFIG_HAPPYMEAL is not set > # CONFIG_NET_POCKET is not set > > # > # Ethernet (1000 Mbit) > # > # CONFIG_ACENIC is not set > # CONFIG_HAMACHI is not set > # CONFIG_YELLOWFIN is not set > # CONFIG_SK98LIN is not set > # CONFIG_FDDI is not set > # CONFIG_HIPPI is not set > # CONFIG_PPP is not set > # CONFIG_SLIP is not set > > # > # Wireless LAN (non-hamradio) > # > # CONFIG_NET_RADIO is not set > > # > # Token Ring devices > # > # CONFIG_TR is not set > # CONFIG_NET_FC is not set > # CONFIG_RCPCI is not set > # CONFIG_SHAPER is not set > > # > # Wan interfaces > # > # CONFIG_WAN is not set > > # > # Amateur Radio support > # > # CONFIG_HAMRADIO is not set > > # > # IrDA (infrared) support > # > # CONFIG_IRDA is not set > > # > # ISDN subsystem > # > # CONFIG_ISDN is not set > > # > # Old CD-ROM drivers (not SCSI, not IDE) > # > # CONFIG_CD_NO_IDESCSI is not set > > # > # Input core support > # > # CONFIG_INPUT is not set > > # > # Character devices > # > CONFIG_VT=y > CONFIG_VT_CONSOLE=y > CONFIG_SERIAL=y > # CONFIG_SERIAL_CONSOLE is not set > # CONFIG_SERIAL_EXTENDED is not set > # CONFIG_SERIAL_NONSTANDARD is not set > CONFIG_UNIX98_PTYS=y > CONFIG_UNIX98_PTY_COUNT=256 > > # > # I2C support > # > CONFIG_I2C=y > # CONFIG_I2C_ALGOBIT is not set > # CONFIG_I2C_ALGOPCF is not set > CONFIG_I2C_CHARDEV=y > > # > # Mice > # > # CONFIG_BUSMOUSE is not set > CONFIG_MOUSE=y > CONFIG_PSMOUSE=y > # CONFIG_82C710_MOUSE is not set > # CONFIG_PC110_PAD is not set > > # > # Joysticks > # > # CONFIG_JOYSTICK is not set > > # > # Input core support is needed for joysticks > # > # CONFIG_QIC02_TAPE is not set > > # > # Watchdog Cards > # > CONFIG_WATCHDOG=y > # CONFIG_WATCHDOG_NOWAYOUT is not set > # CONFIG_SOFT_WATCHDOG is not set > # CONFIG_WDT is not set > # CONFIG_WDTPCI is not set > # CONFIG_PCWATCHDOG is not set > # CONFIG_ACQUIRE_WDT is not set > # CONFIG_ADVANTECH_WDT is not set > # CONFIG_60XX_WDT is not set > # CONFIG_MIXCOMWD is not set > # CONFIG_I810_TCO is not set > # CONFIG_MACHZ_WDT is not set > # CONFIG_INTEL_RNG is not set > # CONFIG_NVRAM is not set > CONFIG_RTC=y > # CONFIG_DTLK is not set > # CONFIG_R3964 is not set > # CONFIG_APPLICOM is not set > > # > # Ftape, the floppy tape device driver > # > # CONFIG_FTAPE is not set > CONFIG_AGP=y > CONFIG_AGP_INTEL=y > CONFIG_AGP_I810=y > CONFIG_AGP_VIA=y > CONFIG_AGP_AMD=y > # CONFIG_AGP_SIS is not set > # CONFIG_AGP_ALI is not set > CONFIG_DRM=y > CONFIG_DRM_TDFX=y > # CONFIG_DRM_GAMMA is not set > # CONFIG_DRM_R128 is not set > CONFIG_DRM_RADEON=y > # CONFIG_DRM_I810 is not set > # CONFIG_DRM_MGA is not set > > # > # Multimedia devices > # > # CONFIG_VIDEO_DEV is not set > > # > # File systems > # > # CONFIG_QUOTA is not set > # CONFIG_AUTOFS_FS is not set > # CONFIG_AUTOFS4_FS is not set > # CONFIG_REISERFS_FS is not set > # CONFIG_REISERFS_CHECK is not set > # CONFIG_ADFS_FS is not set > # CONFIG_ADFS_FS_RW is not set > # CONFIG_AFFS_FS is not set > # CONFIG_HFS_FS is not set > # CONFIG_BFS_FS is not set > CONFIG_FAT_FS=y > CONFIG_MSDOS_FS=y > # CONFIG_UMSDOS_FS is not set > CONFIG_VFAT_FS=y > # CONFIG_EFS_FS is not set > # CONFIG_JFFS_FS is not set > # CONFIG_CRAMFS is not set > CONFIG_TMPFS=y > # CONFIG_RAMFS is not set > CONFIG_ISO9660_FS=y > # CONFIG_JOLIET is not set > # CONFIG_MINIX_FS is not set > # CONFIG_NTFS_FS is not set > # CONFIG_NTFS_RW is not set > # CONFIG_HPFS_FS is not set > CONFIG_PROC_FS=y > # CONFIG_DEVFS_FS is not set > # CONFIG_DEVFS_MOUNT is not set > # CONFIG_DEVFS_DEBUG is not set > CONFIG_DEVPTS_FS=y > # CONFIG_QNX4FS_FS is not set > # CONFIG_QNX4FS_RW is not set > # CONFIG_ROMFS_FS is not set > CONFIG_EXT2_FS=y > # CONFIG_SYSV_FS is not set > # CONFIG_SYSV_FS_WRITE is not set > # CONFIG_UDF_FS is not set > # CONFIG_UDF_RW is not set > # CONFIG_UFS_FS is not set > # CONFIG_UFS_FS_WRITE is not set > > # > # Network File Systems > # > # CONFIG_CODA_FS is not set > CONFIG_NFS_FS=y > CONFIG_NFS_V3=y > # CONFIG_ROOT_NFS is not set > # CONFIG_NFSD is not set > # CONFIG_NFSD_V3 is not set > CONFIG_SUNRPC=y > CONFIG_LOCKD=y > CONFIG_LOCKD_V4=y > # CONFIG_SMB_FS is not set > # CONFIG_NCP_FS is not set > # CONFIG_NCPFS_PACKET_SIGNING is not set > # CONFIG_NCPFS_IOCTL_LOCKING is not set > # CONFIG_NCPFS_STRONG is not set > # CONFIG_NCPFS_NFS_NS is not set > # CONFIG_NCPFS_OS2_NS is not set > # CONFIG_NCPFS_SMALLDOS is not set > # CONFIG_NCPFS_NLS is not set > # CONFIG_NCPFS_EXTRAS is not set > > # > # Partition Types > # > # CONFIG_PARTITION_ADVANCED is not set > CONFIG_MSDOS_PARTITION=y > # CONFIG_SMB_NLS is not set > CONFIG_NLS=y > > # > # Native Language Support > # > CONFIG_NLS_DEFAULT="iso8859-1" > # CONFIG_NLS_CODEPAGE_437 is not set > # CONFIG_NLS_CODEPAGE_737 is not set > # CONFIG_NLS_CODEPAGE_775 is not set > # CONFIG_NLS_CODEPAGE_850 is not set > # CONFIG_NLS_CODEPAGE_852 is not set > # CONFIG_NLS_CODEPAGE_855 is not set > # CONFIG_NLS_CODEPAGE_857 is not set > # CONFIG_NLS_CODEPAGE_860 is not set > # CONFIG_NLS_CODEPAGE_861 is not set > # CONFIG_NLS_CODEPAGE_862 is not set > # CONFIG_NLS_CODEPAGE_863 is not set > # CONFIG_NLS_CODEPAGE_864 is not set > # CONFIG_NLS_CODEPAGE_865 is not set > # CONFIG_NLS_CODEPAGE_866 is not set > # CONFIG_NLS_CODEPAGE_869 is not set > # CONFIG_NLS_CODEPAGE_936 is not set > # CONFIG_NLS_CODEPAGE_950 is not set > # CONFIG_NLS_CODEPAGE_932 is not set > # CONFIG_NLS_CODEPAGE_949 is not set > # CONFIG_NLS_CODEPAGE_874 is not set > # CONFIG_NLS_ISO8859_8 is not set > # CONFIG_NLS_CODEPAGE_1251 is not set > # CONFIG_NLS_ISO8859_1 is not set > # CONFIG_NLS_ISO8859_2 is not set > # CONFIG_NLS_ISO8859_3 is not set > # CONFIG_NLS_ISO8859_4 is not set > # CONFIG_NLS_ISO8859_5 is not set > # CONFIG_NLS_ISO8859_6 is not set > # CONFIG_NLS_ISO8859_7 is not set > # CONFIG_NLS_ISO8859_9 is not set > # CONFIG_NLS_ISO8859_13 is not set > # CONFIG_NLS_ISO8859_14 is not set > # CONFIG_NLS_ISO8859_15 is not set > # CONFIG_NLS_KOI8_R is not set > # CONFIG_NLS_KOI8_U is not set > # CONFIG_NLS_UTF8 is not set > > # > # Console drivers > # > CONFIG_VGA_CONSOLE=y > # CONFIG_VIDEO_SELECT is not set > # CONFIG_MDA_CONSOLE is not set > > # > # Frame-buffer support > # > # CONFIG_FB is not set > > # > # Sound > # > CONFIG_SOUND=y > # CONFIG_SOUND_CMPCI is not set > CONFIG_SOUND_EMU10K1=y > # CONFIG_SOUND_FUSION is not set > # CONFIG_SOUND_CS4281 is not set > # CONFIG_SOUND_ES1370 is not set > # CONFIG_SOUND_ES1371 is not set > # CONFIG_SOUND_ESSSOLO1 is not set > # CONFIG_SOUND_MAESTRO is not set > # CONFIG_SOUND_MAESTRO3 is not set > # CONFIG_SOUND_ICH is not set > # CONFIG_SOUND_SONICVIBES is not set > # CONFIG_SOUND_TRIDENT is not set > # CONFIG_SOUND_MSNDCLAS is not set > # CONFIG_SOUND_MSNDPIN is not set > # CONFIG_SOUND_VIA82CXXX is not set > # CONFIG_SOUND_OSS is not set > # CONFIG_SOUND_TVMIXER is not set > > # > # USB support > # > CONFIG_USB=y > # CONFIG_USB_DEBUG is not set > > # > # Miscellaneous USB options > # > # CONFIG_USB_DEVICEFS is not set > # CONFIG_USB_BANDWIDTH is not set > > # > # USB Controllers > # > CONFIG_USB_UHCI_ALT=y > # CONFIG_USB_OHCI is not set > > # > # USB Device Class drivers > # > # CONFIG_USB_AUDIO is not set > # CONFIG_USB_BLUETOOTH is not set > CONFIG_USB_STORAGE=y > # CONFIG_USB_STORAGE_DEBUG is not set > # CONFIG_USB_STORAGE_FREECOM is not set > # CONFIG_USB_ACM is not set > # CONFIG_USB_PRINTER is not set > > # > # USB Human Interface Devices (HID) > # > > # > # Input core support is needed for USB HID > # > > # > # USB Imaging devices > # > # CONFIG_USB_DC2XX is not set > # CONFIG_USB_MDC800 is not set > # CONFIG_USB_SCANNER is not set > # CONFIG_USB_MICROTEK is not set > > # > # USB Multimedia devices > # > # CONFIG_USB_IBMCAM is not set > # CONFIG_USB_OV511 is not set > # CONFIG_USB_DSBR is not set > # CONFIG_USB_DABUSB is not set > > # > # USB Network adaptors > # > # CONFIG_USB_PLUSB is not set > # CONFIG_USB_PEGASUS is not set > # CONFIG_USB_NET1080 is not set > > # > # USB port drivers > # > # CONFIG_USB_USS720 is not set > > # > # USB Serial Converter support > # > # CONFIG_USB_SERIAL is not set > > # > # USB misc drivers > # > # CONFIG_USB_RIO500 is not set > > # > # Kernel hacking > # > # CONFIG_MAGIC_SYSRQ is not set > > -- > ++++++++++++++++++++++++++++++++++++++++++++++ > Dave Neal, Center for Nonlinear Studies > Phone w/ Voice Mail (505) 665-6471 > Digital Pager - (505) 664-8666 > Wirth's Law: Software gets slower faster than > Hardware gets faster! > ++++++++++++++++++++++++++++++++++++++++++++++ > - > To unsubscribe from this list: send the line "unsubscribe linux-kernel" > in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/