I've got a dual-processor system built around the Intel SBT2 motherboard,
which uses the ServerWorks LE chipset. 2.4.3 SMP works fine. When I
build a UP kernel with IO-APIC support, I get this during boot:
[... everything seems ok until ...]
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ServerWorks OSB4: IDE controller on PCI bus 00 dev 79
ServerWorks OSB4: chipset revision 0
ServerWorks OSB4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x0840-0x0847, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x0848-0x084f, BIOS settings: hdc:DMA, hdd:DMA
spurious APIC interrupt on CPU#0, should never happen.
spurious APIC interrupt on CPU#0, should never happen.
hda: CD-ROM 52X/AKH, ATAPI CD/DVD-ROM drive
spurious APIC interrupt on CPU#0, should never happen.
spurious APIC interrupt on CPU#0, should never happen.
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
spurious APIC interrupt on CPU#0, should never happen.
spurious APIC interrupt on CPU#0, should never happen.
hda: lost interrupt
spurious APIC interrupt on CPU#0, should never happen.
hda: lost interrupt
hda: ATAPI 52X CD-ROM drive, 192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Floppy drive(s): fd0 is 1.44M
spurious APIC interrupt on CPU#0, should never happen.
spurious APIC interrupt on CPU#0, should never happen.
floppy0: no floppy controllers found
Serial driver version 5.05 (2000-12-13) with MANY_PORTS SHARE_IRQ SERIAL_PCI
ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
SCSI subsystem driver Revision: 1.00
(scsi0) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 1/4/0
(scsi0) Wide Channel A, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 392 instructions downloaded
(scsi1) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 1/4/1
(scsi1) Wide Channel B, SCSI ID=7, 32/255 SCBs
(scsi1) Downloading sequencer code... 392 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.1/5.2.0
<Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.1/5.2.0
<Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0
Inquiry 00 00 00 ff 00
spurious APIC interrupt on CPU#0, should never happen.
SCSI host 0 abort (pid 0) timed out - resetting
SCSI bus is being reset for host 0 channel 0.
spurious APIC interrupt on CPU#0, should never happen.
SCSI host 0 channel 0 reset (pid 0) timed out - trying harder
SCSI bus is being reset for host 0 channel 0.
[... repeat above 6 lines until I reset hw ...]
2.4.3 has this behavior, 2.4.3-ac9 works fine. I found this in the -ac
changelog; perhaps it's relevant:
> 2.4.2-ac12
[...]
> o Remove serverworks handling. The BIOS is our (me)
> best (and right now only) hope for that chip
Here's the pertinent (I think) part of 2.4.3 .config:
CONFIG_MPENTIUMIII=y
CONFIG_X86_GOOD_APIC=y
# CONFIG_SMP is not set
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
Details available on request.
Thanks -- Jim
-- Jim Schutt <jaschut@sandia.gov> Sandia National Laboratories, Albuquerque, New Mexico USA- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/